radio AUDI R8 SPYDER 2015 Owners Manual

Instruments and warning/indicator lights
4 Safety belt warning light
Applies to vehicles: with safety belt warning light
The warning light is a reminder to fasten safety
belts.
The warning light . comes on for a few seconds
after the ignition is sw itched on as a reminder to
fasten your safety belt.
Additiona l information on safety be lts
¢page 95.
D Battery
This warning/indicator light detects a malfunc­
tion in the generator or in the vehicle's electrical
system.
The. warning/indicator light ill uminates when
you switch on the ignition and must go out after
the engine has started.
• Alternator fault: Battery is not being charg­
ed
If the indicator light turns on and the message
appears, there is a malfunction in the generator
or vehicle electrical system .
D riv e to you r aut horized Aud i dea le r or qualified
wo rkshop immediately. Because the vehicle bat ­
tery is discharging, turn off all unnecessary elec­
trica l equipment suc h as the radio. Seek profes­
siona l assistance if the battery charge level is too
low.
(•) Low battery: battery will be charged while
driving
If the indicator light turns on and the message
appears, there may be limited star ting ability.
If th is message turns off after a little wh ile, the
battery charged enough wh ile driving .
If the message does not turn off, have your au­
thor ized Audi dealer or qualified workshop cor­
rect the malfunct ion.
14
·~Engine oil pressure
The red engine oil pressure warning symbol re­
quires immediate service or repair .
If the . symbol appears in the display and
flashes, the o il pressure is too low. In add ition to
the symbol, the following message also appears i n the d isp lay:
Switch off engine! Oil pressure is too low
.. Pull off the road and stop the vehicle .
.. Shut the engine down.
.. Check the engine oil level¢
page 159 .
.. Contact your authorized Audi dealer for assis-
tance if necessary.
Engine oil level too low
If the engine oil leve l is too low, top off oil to the
proper level
¢page 160.
Engine oil level OK
If the. symbol starts flashing again even
though the engine oi l level checks OK on the dip­
stick,
do not sta rt driving again and do not let
the engine run at idle .
Instead, contact your au­
thorized Audi dealer for assistance .
(D Tips
- The engine oil pressure symbol. is not
an indicator for a low engine oil level. Do
not rely on it. Instead, check the oil level in
your engine at regular intervals, preferably each time you refuel, and always before
going on a long trip.
- The yellow oil level warning indication
II
requires oil refill or workshop service with­
out delay. Do not wait until the red oil
pressure warning symbol. starts to flash
before you respond to the low oil level
warning
Ill. By then, your engine may al­
ready have suffered serious damage.
-L Engine cooling system
A malfunction in the engine cooling system must
be repaired as soon as possible.
When the. symbol in the display flashes, then
either the engine coo lant
temperature is too IJ,,

Driver information system
Driver information
system
Introduction
The Driver information display inside the instru­
ment cluster provides you, the driver, with im­
portant information.
F ig. 6 Instr um en t cluster: center display
Fig. 7 Wiper lever: controls for the menu display
Center display
With the ignition on, the display in the Driver In­
formation System shows the following informa­
tion :
- CD inserted or Radio station set
- Outs ide temperature: At temperatures below
41 °F (+ S
0
(), a snowflake symbol appears in
front of the temperature display ¢,& .
- Warning when a door, the engine compartment
lid or the trunk lid is not closed.
Additional functions
You can open the following functions in the Driv­
er Information System disp lay by pressing the
I RES ET I button ¢ fig. 7 one or more times:
Digital speedometer*
T ir e pressu re monitoring
¢page 196
20
Trip computer ¢ page 21
Menu display ¢ page 22
Service interval display¢ page 24
Lap timer* ¢page 25
Speed warn ing ¢ page 69
Auto Check Control
Some functions and vehicle components are
scanned for their operating status when you
switch the ignition on and whi le you are driving .
Malfunctions or required service procedures are
signaled audib ly and ind icated by red and yellow
ill uminated symbols and reminders in the dis­
play.
& WARNING -
- Never re ly exclusively on the outside tem­
perature display to determine if a road sur­
face is icy or not. Keep in mind that road sur­
faces, especially bridges and overpasses,
could be ice covered and slippery even at an
outside temperature above 41 °F (+S °C).
-Always remember, even if the "snowflake"
symbol (ice warning) does not appear in the
display, black ice could be on the road.
- Always reduce your speed and drive with
special care in cold weather cond itions when
the chance of encountering icy road surfaces
increases.
(D Tips
On vehicles with Aud i Navigation system, the
displays may differ from their normal appear­
ance during navigation.

Opening and closing
Master key with remote control
The remote control allows you to lock or unlock
the vehicle electronically .
The transmitter and battery are located in the
head of the remote control. The receiver is locat­
ed inside the vehicle . The max imum effective
range depends on several things . Remember, if
the battery is weak, the effective range dec reas­
es .
If you need to replace the remote control , or if
you need to have it repaired, you must see your author ized Audi dealer. Only then can you use the
key again .
0) Tips
-If the ignition is sw itched on, the remote
control system is deact ivated.
- The remote control system can be affected
by other systems operating in the same fre­
quency range close to the vehicle, such as
mobile te lephones, television broadcasting
stations, etc.
- For Declaration of Compliance to United
States FCC and Industry Canada regulations
¢page 218.
Master key battery replacement
Each master key contains a battery housed un­
der the cover.
Fig. 22 Remote master key: opening t he cove r
• Pry apart the base¢ fig. 22 ® and the cover @
carefully with a coin.
• Remove the cover (arrow) .
• Remove the dead battery from the cover .
28
• Insta ll the new battery . Please make certain
that the" +" sign on the battery faces down in
the cover . Correct polarity is shown on the cov­
er.
• Place the cover with the new battery on the key
base and press both parts together .
@ For the sake of the environment
D ispose of dead batteries properly so as not
to pollute the environment.
@ Tips
The replacement battery must be the same
specification as the original.
Electronic immobilizer
The immobilizer helps to prevent unauthorized
use of your vehicle.
A comp uter chip inside your key automatical ly
deactivates the electronic immobilizer when you
insert the key in the ignition lock. When you re­
move the key from the ignition lock, the electron­
ic immobilizer is automatically activated once
again .
A WARNING
Always take the key with you when you leave
the vehicle. The key can disarm the electronic
engine immobilizer and perm it an unauthor­
ized person to start the engine and enab le op­
e rat ion of t he vehicle systems such as power
window leading to serious personal injury.
{D Tips
- The veh icle cannot be started if an una u­
thorized key is used. The vehicle may not
start if another radio device such as a key
for another veh icle or a transponder is locat­
ed on the key ring.
- For Declaration of Compliance to United
States FCC and Industry Canada regulations
r::>page 218.

Opening and closing
@ Tips
- The dr iver's door can be locked and un­
l ocked with the key if the power locking sys­
tem fails. The passenger 's door can be
l ocked manually
c:> page 32.
- In the event of a crash with airbag deploy­
ment all loc ked doors will be automatically
unlocked to give access to the vehicle occu­
pants from the outs ide .
- The anti-t heft alarm system cannot be acti­
vated if the power locking system is not ac­
tivated .
- You are well advised not to keep valuables
i nside an unattended vehicle, v is ible or not.
Eve n a prope rly locked veh icle cannot p ro­
v id e the secur ity of a safe!
Unlocking and locking the vehicle with the
remote control
How the remo te control works.
F ig. 2 3 Remote co ntrol: fun ctio n butto ns
Whether only the d river's doo r or the entire veh i­
cle is unlocked when the opening button @ is
pressed once, depends on the settings in the
Driver information system
Central locking menu
~ page 22 .
To unlock the vehicle III
• Press button @.
• Press but ton @ two
times w ith in two seconds
to unlock all doors and the front lid .
To lock the vehicle
~
• Press button @~.&. in General description on
page 29 .
• Watch that all turn signal lights flash once.
30
To unlock front lid only~
• Press bu tton © for approxima tely one se con d.
PANIC Button
• Push the red button @to activate t he panic
fu nction . The horn sou nds an d the turn signa ls
fla sh.
• Push the button @aga in t o de acti va te the pan-
ic fu nct io n.
The remote cont ro ls allows you to:
- lock or unlock the vehicle
- select ively un lock the front lid.
The turn signa ls will flash brief ly whenever you
l ock or u nlock the veh icle. Also, the interior light
will come on o r go off whenever yo u open or
close the driver's door.
The transm itter and battery are located in the
head of the remote contro l. The receiver is locat­
ed inside the vehicle . The maximum effective
range depends on severa l things . Remembe r, if
the battery is weak, the effect ive range decreas­
es .
The remote -cont ro l key contains a fo ld-out key
that you can use to man ually lock or unlock t he
vehicle and to start the eng ine .
I f you need to replace the remote control , or if
you need to have it repaired, you must see your
authorized Aud i dea ler. Only then can yo u use the
key agai n.
A WARNING
Read and follow all WARNI NGS c:> & in Gener­
al description on page 29 .
(D Tips
- The remote control key is automatically de­
act ivated when the ignition is sw itched on.
- The operation of the remote contro l key can
be temporarily d isrupted by interference
from transmitters in the vicinity of the vehi ­
cle wo rking in the same freque ncy ra nge
(e.g . a cell phone, radio eq uipment).
- In orde r to make su re the locking function is
wor king, you should a lways keep yo ur eye
II>

..... N
r-­N "': ..... \!) 1.1'1
N 1.1'1 .....
previously programmed in phases 1 and 2 for
two seconds and release. Repeat this se­
quence
twice.
"'Some vehicles may require the press/hold/re­
lease sequence up to three times to complete
the training process .
"' HomeLink should now activate your rolling
code equipped device.
If the 5 minute time limit is exceeded, the emer­
gency flashers will flash one time
to indicate
that the process has been terminated . In this
case, repeat steps 4 through 9.
If the emergency flashers do not flash
three
times (after about 15-60 seconds), programming
was not successful. In this case, repeat steps 4
through 9.
Remote control units for garage door openers in
Canada are set to stop transmitting radio fre ­
quency signals after two seconds . This time may
not be sufficient for the Homelink system to
learn the radio frequency signal. Perform all oth­
er steps as described above.
Operating the Homelink transmitter
The Homelink transmitter works in the same
manner as the original handheld remote control
that came with the system.
"'Press the appropriate programmed button
Q),
0 or @ ¢ page 36, fig. 33 to activate the de­
sired remote control function ¢
A. in Descrip­
tion on page 35.
Reprogramming a single button
A Homelink button can be reprogrammed indi­
vidually without affecting the other button allo ­
cations.
Programming the overhead keypad
"'Press the appropriate Homelink button until
the indicator light begins flashing slowly.
Programming the bumper mounted transmit
ter
l. Hold the original remote control at a dis­
tance between
0-5 in . (0-13 cm) from the
Opening and closing
bumper below the appropriate headlight for
your vehicle (use the shortest distance possi­ ble).
2. Aim the remote control just below the
driver
side
headlight.
3. Press and hold the activation button on the remote control.
4. The emergency flashers will flash
three
times
(after about 15-60 seconds) when the
programming is successful. Now release the
button on the remote control.
.. If the device utilizes a rolling code, please fol­
low phase 3 of ¢
page 36, Programming the
Homelink transmitter
for rolling code pro­
gramming.
This procedure will cause the existing program­ ming on the Homelink button to be erased!
Erasing the programming of the Home link
transmitter
When you erase the programming, the program­
ming on all three of the transmitter channels
with be lost!
"' Perform steps 1 to 4 as described on
¢ page 36, Phase 1: programming the over­
head keypad .
When completed, the Home link system will be in
the programming mode and is then ready to
learn the codes for remote controlled devices .
(D Tips
-Programmed buttons cannot be erased indi­
vidually .
- For security reasons you are advised to erase
the programming of the Homelink system
before you sell your vehicle .
37

..... N
r-­N "': ..... \!) ..,.,
N ..,., .....
vehicle can damage a part of an airbag system
and prevent that system from working properly
in a co llision.
There are some important things you have to know to make sure that the effectiveness of the
system wi ll not be impaired and that discarded
components do not cause injury or pollute the
environment.
A WARNING
Improper care, servicing and repair proce­
dures can increase the risk of personal injury
and death by prevent ing an a irbag from de­
ploying when needed or dep loying an airbag
unexpectedly:
- Never cover, obstruct, o r change the steer­
ing wheel horn pad or a irbag cover or the in­
strument panel or mod ify them in any way.
- Never attach any objects such as cup holders
or te lephone moun tings to the su rfaces cov­
er ing the airbag units.
- F or cleaning the ho rn pad or instrument
pane l, use only a soft, d ry cloth or one mois­
tened with plain water. Solvents or cleaners
cou ld damage the a irbag cover or change
the stiffness o r strength of the mater ial so
that the airbag cannot dep loy and protect
properly.
- Never repa ir, adjust, or change any parts of
the airbag system.
- All wo rk on the stee ring wheel, inst rument
pane l, front seats or elect rical system (in­
cluding the installation of aud io equipment,
cellu lar telep hones and CB radios, etc.)
must be performed by a qualified technician
who has the train ing and special eq uipment
necessary.
- For any work on the airbag system, we
strongly recommend that you see you r au­
tho rized Aud i dea le r o r qualified workshop.
- Never mod ify the front bumper or parts of
the vehicle body .
- Always make sure that the side airbag can
inflate without inte rfe rence:
- N ever install seat covers or replacement
up ho lstery over the front seatbacks that
Airbag syste m
have not been specif ically approved by
Audi.
- Never use additional seat c ushions that
cover the areas where the side a irbags in­
flate.
- Damage to the orig inal seat cove rs or to
the seam in the area of the side airbag
module must a lways be repaired immedi­
ate ly by an authorized Aud i dealer .
- The airbag system can be activated only
once. After an airbag has inflated, it must
be rep laced by an authorized A udi dealer or
qualified technic ian who has the technical
info rmation, t raining and specia l equipment
necessary.
- The airbag system can be deployed only
once. After an airbag has been deployed, it m ust be replaced w ith new repla cemen t
p ar ts des igned and app roved especially for
your Aud i model version . Replacement of
comp lete airbag systems or airbag compo­
nents must be perfo rmed by qualified wor k­
shops only. Make sure that any airbag serv­
ice action is entered in your Audi Warranty
&
Maintenance book let under AIRBAG RE­
PLACEMENT RECORD.
- For safety reasons in severe accidents, the
alternator and starte r are separated from
the vehicle batte ry w ith a pyrotechnic circuit
interrupter.
- Work on the pyrotechnic circuit interrupt­
er must on ly be performed by a qua lified
dealer - risk of an acc ident!
- If the vehicle or the circuit interr upter is
scrapped, all applicable safety precautions
must be followed.
@ For the sake of the environment
Undeployed airbag modules and pretension ­
ers might be classified as Perchlorate Material
-specia l hand ling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlo­ rate. When the vehicle or parts of the re­
stra int system including airbag modules and
safety belts with pretensioners are scrapped,
a ll applicable laws and regulations must be ..,_
115

..... N
r-­N "': ..... \!) 1.1'1
N 1.1'1 .....
What you should know
The highest priority is given to maintaining start­
ing capability .
The battery is severely taxed in short-distance
driving, in city traffic and during the cold time of
year . Abundant electrical energy is required, but
only a little is generated . It is also critical if the
engine is not running and electrical components
are turned on. In this instance energy is being
consumed but none is being generated.
It is in precisely these situations that you w ill no­
tice energy management actively regulating the
d istribution of ene rgy.
Vehicle stands for an extended period
If you do not drive your vehicle over a period of
several days or weeks , electr ical components are
gradually cut back or switched off . This reduces
energy consumption and maintains starting ca­
pability over a longer pe riod .
Take into consideration that when you unlock
your veh icle, some convenience functions, such
as the remote key or power seat adjustment, may
not be available. The convenience functions will
be available again when you turn on the ignition
and start the engine .
With the engine turned off
If you listen to the radio, for example, with the
engine turned off, the battery is being dis­
charged .
If starting capability is jeopardized due to energy
consumption, a message appears in the driver in­
formation display .
You have to start the engine to charge the bat ­
tery .
With the engine running
Although electrical energy is generated when the
vehicle is being driven, the battery can become
discharged. This happens mostly when little en­
ergy is be ing generated and a great deal con­
sumed and the battery's state of charge is not
optimal.
Intelligent technology
To bring the energy balance back into equilibri­
um, consumers which require especially large
amounts of energy are temporar ily cut back or
switched off. Heating systems in part icu lar re­
quire a great deal of energy. If you notice, for ex­
ample, that the heated seats* or the heated rear
window are not heating, they have been tempo­
rarily cut back or switched off . These systems w ill
be available again as soon as the energy balance
has been restored.
You w ill also not ice that engine idle speed has
been increased slightly . This is normal and not a
cause for concern. By incr easing eng ine idle
speed the additional energy required is generated
and the battery is charged.
Driver notification in the instrument
cluster display
If battery power drops in to the range where it
can limit the ability of the engine to start, this is
shown in the instrument cluster display w ith the
following driver message :
[•] low battery charge: battery will be charged
while driving
This notification reminds you that the starting
capability of the engine may be limited. As soon
as you start driving again, the battery will be re­
charged and the notificat ion will go out .
Driver notification appears and goes out
again
If this driver notification appears after the igni­
tion is turned on or while driv ing and it goes out
again after a while, the battery has been ade ­
quately recharged .
Driver notification appears and does not go
out again
If this driver notif ication appears after the ign i­
t ion is turned on or while dr iv ing and does not go
out again, the battery's state of charge is not in
t h e optimal range. Starting ability is restricted .
Have the battery checked as soon as possible by
an authorized Audi dea le r or qualified workshop.
141

Checking and filling
thaw completely before attempting to charge it
c> &. . However, we recommend not us ing a
thawed battery again because the battery casing
can be cracked due to ice format ion and can leak
battery acid.
Do no t open the battery caps when charging the
battery .
A WARNING
Charging a battery can be dangerous.
- Never charge a frozen battery. It may ex­
plode because of gas trapped in the ice. Al­
low a frozen battery to thaw out first.
- Do not reuse batteries which were frozen.
The battery housing may have cracked and
weakened when the battery froze.
- Charge the battery in a we ll ventilated area.
Keep away from open flame or electrical
spark. Do not smoke . Hydrogen gas generat­
ed by the battery is explosive .
- To reduce the danger of explosion, never
connect or disconnect charger cables while
the charger is operating .
- Fast charg ing a battery is dangerous and
should only be attempted by a competent
technician with the proper equipment .
- Battery acid that may spill during charg ing
sho uld be washed off w ith a solution of
warm water and baking soda to neutralize
the acid.
CD Note
Never use a fast charger as a booster to start
the engine. This will seriously damage sensi­
tive electronic components, such as control
units, re lays, radio, etc., as well as the batte ry
charger.
@ Tips
- The vehicle battery must not be charged
with a standard small charger that plugs in­
to the cigarette lighter or outl et.
- Only charge the battery through the connec­
tions in the luggage compartment.
168
Windshield washer
container
Fig. 146 Lu ggage compar tment: Wind shi eld wash er fl uid
reservoir
The washer fluid container is marked with the
symbol
Q on its cap c>page 157, fig . 134.
.. Lift the filler cap tongue to add washer fluid.
You can fill the container to the top .
.. Press the cap back onto the filler neck after fill -
ing the container .
You can find the reservoir capacity in the table in
¢page 213
Clean water should be used when filling up. If
possible, use soft water to prevent scaling on the
washer jets. Always add a glass cleaner solution
(with frost protection in the winter).
CD Note
- Do not mix engine coolant antifreeze or any
other additives to fill up the windshield
washer reservoir .
- Do not use glass cleaners containing paint
solvent; you risk damaging the paint.

(D Note
- Please note that summer and
winter t ires are designed for
the conditions that are typical in those seasons . Audi recom­
mends using winter tires dur ­
ing the winter months . Low
temperatures significantly de­
crease the elasticity of summ­
er tires, which affects traction
and braking ability. If summer
tires are used in very cold tem­ peratures, cracks can form on
the tread bars, resulting in
Tires and wheels
permanent tire damage that
can cause loud driving noise
and unbalanced tires . Audi is
not responsible for this type
of damage.
- Burnished, polished or
chromed rims must not be
used in winter road condi­
tions . The surface of the rims
does not have sufficient corro ­
sion protection for this and
could be permanently dam­ aged by road salt or similar
substances .
Glossary of tire and loading terminology
Accessory weight
means the combined weight (in
excess of those standard items
which may be replaced) of auto­
matic transmission, power steer­
ing, power brakes, power win ­
dows , powe r seats , radio , and
heater , to the extent that these
items a re available as factory-in­
stalled equipment (whether in­
stalled or not).
Aspect ratio
means the ratio of the height to
;:;: the width of the tire in percent .
" ~ Numbers of 55 or lower indicate a ...
~ low sidewall for improved steer -
"' ....
ing response and better overall
handling on dry pavement.
Bead
means the part of the tire that is
made of steel wires, wrapped or
reinforced by ply cords and that is
shaped to f it the rim .
Bead separation
means a breakdown of the bond
between components in the bead .
Cord
means the strands forming the
plies in the tire.
17 1
...

Tires and wheels
and tires are compatible with the tire pres­
sure monitoring system. Otherwise the sys­
tem will register a malfunction and a fault message will be displayed. For more infor­
mation, contact your authorized Audi deal­
er.
- For Declaration of Compliance to United
States FCC and Industry Canada regulations
c:> page 218.
Programming a new set of tires
Applies to veh icles: w ith tire pressure monitoring syste m
When driving with a new set of tires, you can pro­
gram them to the tire pressure monitoring sys­
tem using the menu disp lay.
.,. Turn the ignition on .
.,. Select the menu:
Set> Tire pressure > Wheel
change.
.,. Confirm that you would like to begin the pro­
gramming process . The message
Wheel sen­
sors are being initialised. This may take a few
minutes ...
appears in the instrument cluster
display.
You can switch between programmed tire sets at
any time without reinitializing the system.
(D Tips
- If the programming process was not com­
pleted successfully, the message
Wheel
sensors could not be initialised
appears in
the display and them indicator light
turns on. If this happens, repeat the proce­
dure.
- Do not store the tire pressure if there are
snow chains on the tire.
TPMS Tire pressure monitoring system
malfunction
A malfunction can have various causes.
If the [I] warning light in the instrument cluster
flashes for approximately one minute and then
remains continuously illuminated and additional­
ly
the m symbol appears in the display, the tire
pressure monitoring system is not available. The
198
text Tire pressure! System malfunction appears
in the display. This can have various causes.
- A wheel sensor or other component may have
fai led.
- During initialization the system has detected
more than 4 wheels on the vehicle, for example
while driving next to another car with a tire pressure monitoring system.
- Audi replacement parts were not used.
- If snow cha ins are being used, system function
can be compromised due to the shielding prop­
erties of the chains .
- The tire pressure monitoring system may not
be available because of a rad io malfunction.
- Transmitters with the same frequency, such as
radio headphones in the vehicle or radio equip­
ment, can cause a temporary disruption of the
system through excessive electromagnetic
fields .
- Eliminate the interference if you can and then
proceed as follows: Turn off the engine for 20
minutes. Then drive another 10 minutes.
If the
warning light comes on again, you should con­
tact your authorized Audi dealer immediately
to have the problem corrected.
- Do not use commercially available tire sealants.
Otherwise, the electrical components of the
tire pressure monitoring system will no longer
work properly and the sensor for the tire pres­
sure monitoring system will have to be replaced
by a qualified workshop.