infotainment AUDI RS5 CABRIOLET 2015 Owners Manual

M N
er
u..
co ,...., \!) ..,.,
,...., ..,., ,....,
appears in the display. If a fJ is shown, then
the data from the total -trip memory is being
disp layed (memory leve l 2) .
Single-trip memory (Trip computer 1)
The single-t rip memory stores the trip infor ­
mat ion from the time the ignition is turned on
unti l it is turned
off. If the trip is continued
within 2 hours from the time the ignition was
turned
off, the new data will be included in
the calculation of the current trip informa­
tion . If the trip is interrupted for
more than 2
hours
the memory is reset automatically .
Total-trip memory (Trip computer 2)
Unlike the sing le-trip memory, the tota l-trip
memory is not reset automatically. Th is per­
mits you to evaluate your driving data for the
entire period between manual resets.
Operation
The trip computer is controlled by two
switches on the windshield wiper lever.
Fig. 11 Windsh ield w iper lever : contro ls fo r th e trip
co mpute r
Operating
• To disp lay the trip computer memory levels,
press the
I RESET I button @¢ fig. 11 re­
peatedly unti l the desired memory leve l is
shown in the d isplay.
• To d isplay trip information within a memory
level, press the top or bottom part of the
function selection switch @.
The trip computer will not operate unless the ignit ion is on. When you turn on the ignition,
the function that was in use when you last
turned the ign ition
off will be displayed .
Driver information display 25
In addition to information about the trip com­
puter (trip computer 1 and 2), information
about other systems can a lso be shown in the
display. To switch the display between the dif­
ferent information, tap the
I RESET I button @
briefly.
Resetting values to zero
• Select a value in the desired trip comp uter.
• Press and hold the
I RESET I button @for at
least one second. All values in the selected
trip computer are reset to zero.
With some vehicle equipment levels, the val ­
ues for the sing le trip or total trip memory
can a lso be reset in the Infotainment system
¢page 25.
(!) Tips
All stored va lues will be lost if the veh icle
battery is disconnected.
Basic Settings for the trip computer
The radio or MMI* operating unit is used for
setting the trip computer's basic settings.
• Select: Function button !CAR !> Instrument
cluster > On-board computer
1 or On-board
computer
2.
The values in the sing le-trip or the total-trip
memory can all be reset to zero at the same
time under
Reset in the menu.
In addition, yo u can determine what informa ­
tion from the trip computer should be shown
in the instrument cluster display. If one of the
pieces of driver information is turned
Off , that
driver information will not be shown in the
display. The information w ill continue to be
calculated by the tr ip computer and can be
turned back
On at any time.
(j) Tips
This function is not available on all
vehicles.

"' N
a: LL co
rl I.O
"' rl
"' rl
door opener> Program garage door open­
er.
If this path is not available, program the
button as described in version
Bqpage41 .
.,. Follow the instructions in the MMI.
Erasing button programming
The programmed buttons cannot be erased
individually. They must all be erased together.
Reprogram the buttons if necessary .
.,. Select:
ICARI function button> Car systems*
control button > Vehicle settings > Garage
door opener> Clear program settings
>
Yes .
Displaying the version/status/country
code
.,. Select: I CARI function button > Car systems*
control button > Vehicle settings > Garage
door opener > Version information.
@ Tips
-Programming through the MMI* is not
possible with all infotainment systems.
If this is the case, program the buttons
as described in version B
c:> page 41.
- The required distance between the hand
transmitter and the HomeLink module in
the radiator grille
c:> page 41; fig. 35
depends on the system that you are pro­
gram ming.
- Depending on the model of the system,
you may need to release the button on
the remote control during programming
and press it again. Hold each position
you try for at least 15 seconds before
trying another position. Keep the turn
signals on your vehicle in view when do­
ing this.
- After programming the garage door
opener, it may be necessary to synchron­i ze the motor with the system. Refer to
the manufacturer's instructions.
Opening and closing 41
Programming the buttons (version 8)
Applies to vehicles: with garage door opener (Homelink)
Fig. 35 Distance be tween the ra diato r grille and the
hand transmitter
Programming the button: Part 1 with the
controls
1. Switch the ignition on.
2. Press and hold both outer buttons in the
roof headliner
c:> page 40, fig. 34 until the
LED @turns off completely (after about
20 seconds). This procedure clears the
standard codes that were set at the facto ­
ry and does
not need to be repeated again
to program the other buttons.
3. Briefly press the button on the roof head­
liner that you would like to program.
4. Wait until the LED @ begins to blink
quickly. Programming mode is active for 5
minutes.
5. Move in front of your vehicle while hold­
ing the original remote control for the
system that would like to program to a
button in the roof headliner.
Programming the button: Part 2 at the
radiator grille
6. Hold the remote control up to the radiator
grille on your vehicle
c:> fig. 35.
7. Press and hold the remote control until
the turn signals on your vehicle blink. This
may take up to 30 seconds.
8. If the emergency flashers blink three
times, the programming was successful.
If the emergency flashers only blink one
time, the 5 minute time limit for the pro­
gramming has ended or the programming
was not successful. Repeat the program­
ming from the third step, or try changing
t he distance to the radiator grille. .,.