warning light AUDI S3 2009 User Guide

qualified workshop=> &. With the eng ine not running (e .g . when
t he car is being towed), there is also no power assis t availa ble.
& WARNING
If there is a malfunction , the indi cator light for the electro -mechan ­
ical power assist illuminates . Seek profess ion al assistance . •
Controls and equip ­
ment
Instruments and warning /indi cator lights
I • •

& WARNING (continued)
• Always remember, even if the "snowflake" symbol (ice
warning) does not appear in the display, black ice could be on the
road.
• Always reduce your speed and drive with special care in cold
weather conditions when the chance of encountering icy road
surfaces increases.
[ i] Tips
• If the vehicle is stationary , or if you are driving at a very low
speed, the temperature shown in the display might be slightly
higher than the actual outside temperature. This is caused by the
heat being radiated from the engine.
• On vehicles with S tronic, the reminders do not appear in the
display until you select a gear .
• On vehicles with Audi Navigatio n system*, the displays may
differ from their normal appearance during navigation. •
Applies to ve hicles: with g ears hift indicator and manual transmi ssio n
Gearshift recommendation
This indicator can help conserve fuel.
Controls and equip ­
ment
+55°F
~ 340mi
3~4 Fig . 8 Gearshift
recommendation
Driver information display
In order to become familiar with the gearshift indicator , begin
driving as usual. If the current gear is not the best one for
conserving fuel, the indicator will display the recommended gear .
The display shows the current gear and the recommended gear
=> fig. 8 .
• Upshifting: The display is to the right of the current gear if a
higher gear is recommended.
• Downshifting: The display is to the left of the current gear if a
lower gear is recommended.
Sometimes the indicator will recommend skipping a gear (3.,. 5l.
[ i] Tips
• This indicator should help you conserve fuel. It is not designed
to recommend the correct gear in all driving situations. Only the
driver can decide which gear is correct in certain driving situations
such as when accelerating or driving on hills.
• The display switches off when the clutch pedal is pressed .
• Gear shift recommendation can be deactivated in the driver
information system=>
page 23. •
I • •

On-Board Diagnostic system (08D)
On-Board Diagnostics
Fig. 10 location of
Data Link Connecto r
( DL C)
On-Board Diagnostics monitors the components of your emission
control system . Each controlled component in your engine system
has been assigned a code. In case of a malfunction , the component
will be identified and the fault stored as a code in the control
module memory .
The Mil lamp may also illuminate if there is a leak in the on-board
fuel vapor recovery system . If the light illuminates after a refuelling,
pull off the road and stop the vehicle, then check that the fuel filler
cap is properly closed=>
page 227.
In order to make an accurate diagnosis, the stored data can only be
displayed using special diagnostic equipment (generic scan tool for
OBDl.
In order to connect the special diagnostic equipment, push the plug
into the Data Link Connector (DLC). The DLC is located to the right of
the engine hood re lease lever=>
page 21, fig. 10 .
Your authorized Audi dealer or a qualified service station can inter ­
pret the code and perform the necessary repair. •
Contro ls and eq uip­
ment
Driver information display
Malfunction Indicator Lamp (MIL) (USA
models)/ (Canada models)
The Malfunction Indicator Lamp (MIU in the instrument cluster
=> page 17, fig . 5 is part of the On-Board Diagnostic (OBD II) system .
The warning/indicator light illuminates when the ignition is
switched on and goes out after the engine starts and the idle has
stabilized. This indicates that the Mil is working properly .
If the light does not go out after the engine is started, or illuminates
while you are driving, a ma lfunction may exist in the engine system.
If the light starts flashing, the catalytic converter cou ld be damaged.
Continue driving
with reduced power (avoiding sustained high
speeds and/or rapid accelerations) and have the condition
corrected . Contact your authorized Audi dealer.
If the light illuminates , the electronic speed limiter may also be
malfunctioning. For more information=>
page 27, "Electronic speed
limiter".
An improperly closed fuel filler cap may also cause the MIL light to
illuminate => page 221. •
Electronic speed limiter
Your vehicle may be factory equipped with tires that are rated for a
maximum speed of 130 mph (210 km/h) . This is less than the
maximum speed of your vehicle. To reduce the risk of sudden tire
failure and loss of control if the vehicle is operated at excessive
speeds, yo ur vehicle also has an electronic speed limiter. The elec­
tronic speed limiter prevents your vehicle from going faster than the
tire speed rating. For more information
=> page 257, "Speed rating
(letter code)".
If the engine control unit receives faulty vehicle roadspeed signals,
the Malfun cti on Indicator Light (MIU will illuminate . If this
occurs, contact the nearest authori zed Audi dealer for assistance. _.,
Vehicle care I I irechnical data

Driver informati on displ ay
Fig. 1 4 Display : Start
menu
Some functions in your vehicle can be set, activated, and controlled
by
M enu s (e.g. Acoustic park assist*). With these menus you can
also select the information shown in the driver information system,
which operates only with the ignition switched on. Operation is
control led by the
I Reset) button and the rocker switch on the wiper
lever =>
page 23, fig. 13 .
The
S ta rt m enu shows you the different disp lay types :
Set
C he ck
M enu off
Each display type in the Start menu contains a submenu with addi­
tiona l options .
Set
C he ck
M enu off
Clock => page 26
Computer => page26
Speed alarm (speed => page27
warning)
Language (6 languages)
Units (distance, fuel con-
=> page26
sumption, temperature)
Displays (gearshift rec -=> page 19
ommendationl
Lighting* (exterior lights, => page 56
turn signals) => page 59
Wiper (service position) => page 66
Window => page 47
Doors (Auto-lock)
Acoustic park assist*
Service
=> page38
=> page 112
=> page20
Chassis number* => page 298
Engine oil temperature*
Registered keys
=> page 35
All of the messages shown in vehicles without
menu display appear on the display screen.
•

Driver informati on displ ay
Selecting settings
The Driver Information System settings are menu-guided.
Select your settings as follows:
Fig . 17 Dis play: Men u
Sett ings, co mputer
sel ected (page 1)
- Press the !Reset] button. The Start menu appears
~ page 24, fig. 14.
- Press the rocker switch until
Set is displayed.
- Press the [Reset] button. All the menus appear.
- Press the rocker switc h until the desired line is hig h-
lighted (cursor)~ fig. 17.
- Press the !Reset] button .
- If necessa ry, scroll by selecting and activating t he
symbol for "Next page" or "Previous page".
When you have selected the Computer menu and activated it by
pressing the
I Reset] button, two computer levels appear (computer
1 and computer 2) . Now you have to select the level you want using
the rocker switch and activate it with the [R ese t] button. •
Speed warning system
Overview
The speed warning system hel ps you to keep your driv ing
speed below a set speed limit.
F ig. 18 Disp lay : sp ee d
w arni ng s yste m
The speed warning system warns the dr iver if he exceeds a previ ­
ous ly stored maximum speed . A warning tone will sound as soon as
the vehicle speed exceeds the set speed by about 3 mph (3 km/h). At
the same time, a warning symbol appears in the display=> fig. 18.
The speed war ning system has
two warn ing thre shold s that func­
tion independently of each other and that have somewhat different
purposes :
Spee d warning 1 ~ / (Canad a mod els)
You can use speed warning 1 to set the maximum speed whi le you
are driving. This setting will remain in effect until you turn off the
ignition, assuming that you have not changed or reset the set ting.
The speed warning symbo l / (Canada models) in the warning 1
display appears when you exceed the maximum speed. It goes out
when the speed falls below the stored maximum speed.
T he speed warning symbol wi ll also go out if the speed
exceeds the
stored maximum speed by more than about 25 mph (40 km/h) for at
leas t 10 seconds . The stored maximum speed is deleted. .,_

Yellow symbols
A yellow symbol means WARNING.
Contro ls and eq uip­
ment
Low fuel level
Check engine oil level Engine oil sensor malfunction
E ng ine spee d limitation
Worn brake pads
USA mode ls:
Speed warning 1
Can ada m od els:
Speed warning 1
USA mod els:
Speed wa rning 2
C ana da m odels:
Speed warning 2
Dynamic headlight range con-
trol* defective
Windshield washer fluid leve l low
Ba ttery voltage too high or too
low
Defective light bulb
USA m odel s:
Defective brake light
=> page 32
=> page32
-
=> page32
=> page32
=> page32
=> page33
=> page33
=> page33
=> page33
=> page33
=> page33
=> page33
=> page 33
=> page33
-
-
Dri ver inf orm atio n di spl ay
Ca nad a m ode ls: => page33
Defective brake light
Light/rain sensor defect ive (auto-
=> page 34
matic headlights)* defective
Adapt ive Light* defective
=> page 34
Ti re pressure monitoring system* => page 34
When a yellow symbol appears, a warning tone will sound once .
Check the displayed function as soon as possible. If more than one
malfunction is detected, all symbols will appear one after the other
for about two seconds. •
Driver information
In addition to the warning/indicator lights and the
symbols in the instrument cluster display, driver informa­ tion is displayed.
Fi g. 2 1 Section of
in stru ment cl uster:
Set/C hec k b utto n
Driver information appears in the display when a defective light
bulb is reported by the defective light bulb warning=>
page 33,
when the brake pads are worn and before you engage a gear on
vehicles with S tronic.
Vehicle care I I irechnical data

Driver inf ormati on displ ay
In addition, driver information may appear when a red symbol
fl ashes in the driver disp lay .
To disp lay Drive r inf orma tion
As an example, the~ symbo l appears in the disp lay. If you now
press the button=>
page 29 , fig. 21 , the following driver message
appears in the display:
Switc h off eng ine and ch eck oil leve l
The driver message in the disp lay goes out after about
5 seconds.
You can display the driver message again by briefly pressing the button .•
Brake system malfunction
BRAKE (USA models) /((D) (Canada models)
The indicator light flashes if the brake fluid level is too
low, if there is a malfunction in the ABS system or when
the parking brake is engaged.
If the BRAKE /((D) symbol flashes in the display with the
parking brake released , there is a ma lfunction in the brake
system. In addition to the symbol, one of two messages
appears in the display :
Stop vehi cle and che ck br ake fluid
ABS f ault
! S ee owner' s manual
- Pull off the road and stop the vehic le.
- Obtain professiona l assistance.
USA models : if there is a malfunction in the ABS system, the -
warning/indicator light i lluminates along with the BRAKE system
malfunction warning /indicator light=>&.
Canada models : if there is a malfunction in the ABS system , the
warning/ indicator light illuminates together with the ((])) brake
system malfunction warning/indicator light=>&.
Parking br ake se t
The parking brake warning light Brake/((])) (Canada mode ls} i llumi ­
nates when the parking brake is set. In addition, a warning tone will
sound after you have driven fo r longer than 3 seconds and faster
t han
3 mph (5 km/h}.
& WARNING
• Alwa ys observe the warning s in => pag e 217, "Engine compart ­
me nt", befor e op en ing the eng in e hood and ch ec king th e br ake
flu id.
• Driving w ith lo w brak e fluid is a sa fe ty hazar d! S top the car an d
g et prof es si onal a ssistance .
• If the br ake system wa rnin g/ ind icator l ight illum in ate s
t o geth er with th e AB S wa rning /indi cator light , then the AB S
sy stem i s ma lfuncti oni ng. Th e re ar w heels c ould quickly lock up
whe n you apply the brak es. Thi s could lead to l oss of control and
you r ve hicle cou ld slid e! Dr iv e ca re fully to th e nearest au thori ze d
Au di d ea le r and have th e malfun ction correct ed. •
Engine cooling system malfunction _}_
A malfunction in the engine cooling system must be
repaired as soon as possible.
When the - t symbol in the display flashes , then either the
engine coolant temperature is too high, or the coolant level
is too low . In addition to the symbol, the following message
also appears in the display :
Switch off engin e and ch ec k coolant level
- Pull off the road and stop the vehicle .

-Turn off the engine.
- Check coolant level => page
233 .
-Add coolant if necessary => page 234 .
-Continue driving only after the engine coolant
warning/indicator light goes out.
- Contact your authorized Audi dealer for assistance if
necessary.
If the engine coolant level is correct, then the radiator fan may be
the cause of the malfunction.
If the generator warning/indicator light should also illuminate
=> page 14, then the fan belt may be damaged .
& WARNING
• If your vehicle should break down for mechanical or other
reasons, park at a safe distance from moving traffic, turn off the
engine and turn on the hazard warning lights
=> page 58, "Emer­
gency flasher
A".
• Never open the hood if you see or hear steam or coolant
escaping from the engine compartment -you risk being scalded.
Wait until you can no longer see or hear steam or coolant
escaping.
• The engine compartment of any vehicle is a dangerous area.
Before you perform any work in the engine compartment, turn off
the engine and allow it to cool . Follow the warning stickers
=> page 217, "Engine compartment" .
0 Note
Do not continue driving if the -IL symbol illuminates. There is a
malfunction in the engine cooling system -you could damage your
engine. •
Controls and equip ­
ment
Driver information display
Engine oil pressure malfunction 'l=;:f.
The red engine oil pressure warning symbol requires
immediate service or repair.
If the 'l=::7-: symbol appears in the display and flashes, the oil
pressure is too low. In addition to the symbol, the following
message also appears in the display:
Switch off engine and check oil level
-Pull off the road and stop the vehicle.
Shut the engine down.
Check the engine oil level=> page
229.
Contact your authorized Audi dealer for assistance if
necessary.
Engine oil level too low
If the engine oil level is too low, top off oil to the proper level
=> page 230.
Engine oil level OK
If the ~ symbol star ts flashing again even though the engine oil
level checks OK on the dipstick,
do not start driving again and do not
let the engine run at idle .
Instead, contact your authorized Audi
dealer for assistance.
[ i] Tips
• The engine oil pressure symbol ~ is not an indicator for a low
engine oil level. Do not rely on it. Instead, check the oil level in your
engine at regular intervals, preferably each time you refuel, and
always before going on a long trip.
• The yellow oil level warning indication requires oil refill or
workshop service without delay. Do not wait until the red oil pres ­
sure warning symbol
~ starts to flash before you respond to the ...
I • •

Driver information display
low oil level warning . By then , your engine may alre ady have
suffered seriou s damage. •
Applies to vehic les: w ith eng in e spee d lim itat ion
Engine speed limitation 1<
Engine speed ma ximum XX.XX RPM
The J symbo l illuminate s when there is an engine cont rol malfunc ­
tion . T he indicator l ight
..J., in the instrument cluster also illum i­
nates. The engine speed is limited to the speed displayed in the
d river in for mation system. Keep in mind tha t the engine speed w ill
not exceed the va lue displayed in the driver information system, for
example when downshifting.
Please go to an authorized Audi dealer or other qua lified workshop
to have the ma lf u nct ion re paired. •
Fuel supply too low
When th e L symbol illuminates, this mea ns th ere are about 2 .6
gallons (10 liters) of fuel left in the fuel tank . Time to refuel!
~ p age 220 .
If the symbol l ights up, eve n when there is ample fuel in the tank,
and the text
Tank system malfunction! Please contact workshop
appears i n the d is pl ay, ther e is a fau lt in the syste m. C ontac t a qual ­
ified workshop to have the fault rectified. •
Checking the engine oil level .2'..
~ Please add max. 1 qt of engine oil!
If th e sy mbol co mes o n, a dd 1 q uart (1 lit er) of oil a t the next
opportunity~
page 230 . •
Checking the engine oil level ~
When the symbol illuminates, c heck the engine oil level as soon
as po ssi ble~
page 22 9. Top off t he o il at your ear liest o pp o rt un ity
~ page 230 . •
Engine oil sensor defective ...
If the -symbol illuminates, contact your authorized Audi dea ler
an d h ave the oil se nso r ins pected. •
Worn brake pads
-Brake pads!
If the warn ing light illuminates, immediate ly contact your autho ­
riz ed Aud i dea ler o r qua lifi ed worksh op to have all bra ke pads
inspected. On USA models the warning light comes on together
with the wa rning ligh t
BRAKE . Both sets of brake pads on an ax le m ust
a lways be replaced at the same time .
& WARNING
Driving with bad brakes can cause a collision and serious personal
injury.
• If the warning light
C. and the warning l ight BRAKE1l with the
message Brake pads! comes on in the in strument cluster display ,
immediately conta ct your authorized Audi dealer or qualified
workshop to have all brake pads checked or replaced if necessary .•
1 1 BRAK£ : USA mod els only

Speed warning 1 C (USA models) /'" (Canada
models)
If the symbol illuminates, this means you are driving faster than
the set vehicle speed. Slow down!=>
page 26. •
Speed warning 2
models) (
USA models) / (Canada
If the symbol illuminates, this means you have driven faster than
the second set vehicle speed. Slow down! =>
page 26. •
App lies to vehicles: w ith dynamic headlight range adjustment
Headlight range control defective ~ >
If the ·r illuminates, the dynamic headlight range control is no
longer working properly. Have the system checked and repaired at
your authorized Audi dealer. •
Windshield washer fluid level too low ' · '
If the rt symbol illuminates, add windshield washer fluid to the
washer system=>
page 241. •
Battery voltage low D
If the t::J symbol illuminates, contact your authorized Audi dealer
and have the following components inspected:
• drive belt
• battery charge
Also see if the generator warning/indicator light illuminates
=>
page 14. •
Controls and equip ­
ment
Driver information display
Defective light bulb warning ~
The defective light bulb warning tells you when a vehicle
light bulb has become defective.
If a defective bulb has been detected by the system or a light bulb
burns out, the ' symbol with a message appears in the display to
tell you which bulb is burnt out and where it is located. For example:
Rear left turn signal
After 5 seconds, the message disappears. If you want to recall the
message into the display, press the CHECK button=>
page 8, fig. 2
©-
There are three reasons why the defective bulb message would
appear in the display:
• The light bulb has burnt out=>
page 285.
• The fuse is "blown" => page 280, "Replacing a fuse" .
• Th e wire connection to the light bulb is defective.
Have the bulb replaced or the connection repaired by your autho­
rized Audi Service department.
& WARNING
• Light bulbs are pressurized and could explode while they are
being changed causing serious personal injury.
• Work with due care when handling the high-voltage section of
gas discharge (xenon) lamps. Failing to do so could result in death
or serious injury! •
Brake light defective BR !.I" (USA
models) / (Canada models)
In case of a malfunction or component failure, the symbol
(USA models)/ (Canada models) can appear. The following elec- .,_
I • •