ECO mode AUDI S3 2016 User Guide

Driving
If you anticipate what you need to do next and
drive economically, you can easily cut your fuel
consumption by 10-15 percent. This section will
give you some tips on how you can help the envi­ ronment and your pocketbook.
(D Tips
The consumption estimates as published by ENVIRONMENTAL PROTECTION AGENCY
(EPA) and Transport Canada may not corre­
spond to your actual consumption on the
road, which will vary depending upon vehicle
load and speed, road and weather conditions,
trip length, etc.
Drive smoothly and keep a lookout ahead
Vehicles use the most fuel when they are acceler­
ating.
.. Avoid unnecessary accelerating and braking .
Vehicles use the most fuel when they are acceler­
ating. If you anticipate what is going to happen next, you will need to brake less and, thus, accel­
erate less. Let the vehicle coast whenever possi ­
ble -for example when you see that the next traf­
fic light is red.
Avoid full throttle
Driving at moderate speeds saves fuel and im­
proves your mileage.
.. Try and keep well below your car's maximum
speed .
Accelerating gently reduces fuel consumption,
engine wear, and does not disturb the environ­ ment.
Fuel consumption, exhaust emissions and engine
noise increase disproportionately at high speeds.
If you drive at approximately three quarters of
top speed, fuel consumption will be reduced by
one half . Never drive faster than the posted
speed limit and weather conditions permit.
78
· Reducing unnecessary idling
Even when your car is just idling it burns up fuel .
.. Shut the engine off when you are not driving
the vehicle .
.,. Do not warm up the vehicle by letting the en-
gine run at idle .
It is efficient to switch off the engine when stop­
ped at railroad crossings and long red lights.
Turning the engine off for just 30 -40 seconds
saves more fuel than is burned by starting the
engine again .
It takes a long time for the engine to warm up
fully when it is running at idle . However, wear
and noxious emissions are especially high when
the engine is warming up . So you should drive
away as soon as you start the engine and avoid running at high rpms while the engine is still
warming up .
@ Note
Do not leave engine idling unattended after
starting. If warning lights should come on to
indicate improper operation, they would go
unheeded. Extended idling also produces
heat, which could result in overheating or
other damage to the vehicle or other proper­
ty.
Regular maintenance
A badly tuned engine unnecessarily wastes a lot
of fuel.
.. Have your vehicle serviced at regular intervals.
By having your vehicle regularly serviced by an
Audi dealer helps to ensure that it runs properly
and economically. The condition of your vehicle
not only affects its safety and ability to hold its
value, it also affects
fuel consumption.
Check your oil each time you fill your tank.
The amount of oil used is related to engine load
and speed.
It is normal for the oil consumption of a new en­
gine to reach its lowest value after a certain mile -
age has been driven . ..,.

.... N
0 > CX)
rl I.Cl U"I
rl I.Cl ....
This message appears and a warning tone sounds if you open the driver's door when the ignition is
switched on. Switch the ign ition off so that the
battery will not d ischarge.
Pressing start/stop button again will switch off
engine!
This message appears when you press the
ISTART ENGINE STOPI* button while driving
¢ page 83, Emergency off function.
Engine start system malfunction. Please con­
tact Service
The engine automatic start system has a mal­
function . Drive to an author ized Audi dealer or
author ized Audi Service Facility immediate ly to
have the malf uncti on corrected. To start the en­
g ine, press and hold the
!START ENGINE STOPI
button.
DJ Key not recognized. See owner's manual
This message appears if there is no convenience
key inside the vehicle or if the system does not
recognize the key. The conven ience key may not
be recognized, for example, if it is covered by an
object that
disrupts the signal (such as a brief­
case), o r if the key battery is weak. Electronic de­
vices such as cell phones can also interfere with
the signal.
To still be able to start or stop the engine, refer
to "Cor rect ing a malfunction" ¢
page 84.
Ill Key not in vehicle?
The Ill indicator light turns on and this message
appears if the convenience key was removed from
the vehicle when the eng ine was running . If the
conven ience key is no longer in the vehicle, you
cannot switch the ignition on o r start the engine
once yo u stop it. In addition, you cannot lock the
ve hicl e from the outside .
Press brake pedal
This message appears if you do not press the
brake pedal when starting the eng ine .
Please engage N or P
This message appears when starting or s topping
the engine if the selector lever is not in the Nor P
position . The engine will not start/stop .
Driving
Shift to P, vehicle can roll away . Doors can only
be locked in P
T his message appears for safety reasons along
with a warning tone. It appears if the selec to r
lever for the automat ic transmission is not in the
P position when switching the ignition off with
the
I START ENGINE STOPI * button. Shift these­
lector lever to the P position. Otherwise, the vehi­
cle could roll. You also cannot lock the vehicle us­
ing the locking sensor o n the door hand le or us ­
ing the conven ience key.
Electromechanical
parking brake
Operating
The electromechanical parking brake replaces
the hand brake.
Fig . 80 Center console : pa rk ing brake
" Pull the switch @¢ fig. 80 to set the parking
brake. The - (USA models),. (Canada
models) ind icator lights in the button and in
the instrument cluster display turn on .
" To release the parking brake, press the brake or
accelerator pedal while the ign ition is switched
on and press the button @at the same time.
The - (USA models), . (Canada models)
ind icator lights in the button and in the display
turn off.
Your vehicle is equipped with an electromechani­
cal park ing brake. The parking brake is designed
to prevent the vehicle from rolling un intent io nal ­
ly and replaces the hand brake .
In addition to the normal functions of a tradi­
t ional hand brake, the electromec hanical parking ..,.
85

,....,
N
0 > co ,...., Automatic transmission S tronic
Introduction
App lies to vehicles: with S tronic transm ission
Your veh icle is equipped with an e lectron ically­
controlled DSG transmiss ion called S tronic. Two
independent clutches transfer the power be­
tween the engine and transmission . It allows the
vehicle to accelerate without a noticeable inter­ ruption in traction.
The transm ission upshifts or downsh ifts auto­
matica lly. The driving sty le continuously influen ­
ces the selection of the driving program.
When a
moderate driving style is used , the
transmission selects the most economical driving
mode. The transmission upshifts at a lower RPM
and downshifts at a higher RPM to improve fuel
efficiency.
The transm ission switches to a sporty mode after
a kick-down o r when the driver uses a
sporty
driving style
characterized by quick accelerator
pedal movements, heavy acce leration , frequent
changes in speed and traveling at the maximum
speed.
If desired, the driver can also select the gears
manually (tiptronic mode) ¢ page 94, Shifting
manually (tiptronic mode) .
Selector lever positions
Applies to vehicles: with S tro nic t ra n sm issio n
Fig. 81 Instrument clus te r: selec tor leve r posi tions
-~ 0 > (X) a,
The instrument cluster display shows the current
selector lever position and current gear .
Automatic transmission
P -Park
The wheels are mechan ically locked in this posi­
tion. You can only shi ft into Park when the vehi­
cle is
stationary ¢&. .
To s hift in and out of the P selector lever posi­
tion, press the interlock button in the selector
lever
while pressing the brake pedal.
R- Reverse
Only shift into reverse gear when the vehicle is
stationary and the engine is running at idle
speed¢ ,&..
T o select the R selector lever position, press the
interlock button
while pressing the brake pedal.
T he back- up lights switch on in the R position if
the ignition is switched on.
N - Neutral
The transmission is in idle in this position .
D/S - Normal position for driving forward
In the D/S se lector lever position, the transmis­
sion can be operated either in the normal D mode
or in the S sport mode. To select the S sport
mode, pull the selector lever back briefly . Pulling
the lever back again will select the normal D
mode . The instrument cluster display shows the
selected driving mode.
In the
normal mode D, the transmission auto­
matically selects the suitable gear ratio . It de ­
pends on engine load, vehicle speed and driving
style .
Se lect the
sport mode S for sporty driving. The
vehicle makes full use of the engine's power .
Sh ifting may become noticeable when accelerat­
ing.
To move from selector lever position N to D, you
must press the brake pedal and the vehicle must
be traveling less than 1 mph (2 km/h) or be sta­
tionary ¢&. .
,&. WARNING
Read and follow all WARNINGS.
- The vehicle can roll even if the ignit ion is
switched off.
89

Automatic transmissio n
Stopp ing /park ing
If the se lecto r lever is not in the P posit ion when
you open the driver's door, the vehicle could roll .
In vehicles with a convenience key*, the message:
Shift to P , vehicle can roll away . Doors c an be
lo cked onl y in P
appears. You will a lso hear a
warn ing tone.
... Press and hold the brake pedal¢_&. .
... Set the parking brake.
.,. Se lect the P selector lever position.
Stopp ing on an inclin e
.,. Always press the brake peda l to hold the vehi ­
cle in place and prevent it from "rolling back"
¢ _&. . Do
not try to prevent the vehicle from
"ro lling back" when a gear is engaged by in­
creasing the engine speed ¢(D.
Starting on an inclin e in vehicl es without Hill
H old *
... Set the parking brake.
.,. With the driving gear selected, press the acce l­
erator pedal carefully. The parking brake re­
leases automatically . Requirement : the driver's
door must be closed and the driver's safety belt must be fastened .
Starting on an incline in veh icles with Hill
Hold*
.,. With the driving gear selected, remove your
foot from the brake pedal and press the accel­
erator pedal~
page 87, Hill hold.
Under certain c ircumstances, (such as driv ing in
the mountains or towing a trailer), it may be use­
fu l to sw itch temporarily to the manua l shift p ro­
g ram in o rde r to adjust the gea rs to the driving
conditions by hand
c:? page 94.
When parking on a level surface, simply place the
selecto r leve r in the P position. On inclines, act i­
vate the parking brake first and then move the
selector lever to the P posi tion
~ page 85. This
prevents the loc king mechanism from being
loaded too heav ily and wi ll make it easier to
move the selector lever out of the P position.
92
A WARNING
- The vehicle can roll even when the engine is
sw itched off.
- Unintended vehicle movement can lead to
serious injuries.
- Never leave your veh icle with the engine
running while in gear. If you must leave
your veh icle when the engine is running, set
the park ing brake and move the selector lev­
er to the P posit ion.
- Power is still transferred to the wheels when the engine is running at idle . To pre­
vent the vehicle from "creeping", yo u must
keep your foot on t he b rake when the en­
gine is ru nning and the selector lever is in
the D, Sor R position or "tip tronic" mode is
selected.
- Do not inadve rten tly p ress the accelerator
pedal when the vehicle is stationary. Other ­
wise the vehicle will start to move immedi­
ately, even if the parking brake is set. This
could result in a crash.
- Do not press the acce lerator pedal when
changing the selector lever posit ion while
the vehicle is stat ionary and the engine is
running.
- Never engage the R or P selector level pos i­
tions while dr iv ing. It could cause a crash.
- Before driving down a steep slope, reduce your speed and shift into a lower gear w ith
"t i ptronic".
- Do not ride the brakes or press the brake pedal too often o r too long when dr iv ing
downhill. Constant braking causes the brakes to overheat and substant ially re­
duces bra king performance, increases b rak­
ing d istance or causes comp lete failure of
the bra ke sys tem.
- If you must stop on an incline, always hold
the vehicle in place w ith the foot brake or
p ar king bra ke to p revent it from rolling
back.
- Never hold the vehicle on an incline with a
slipping clu tch. The clutch opens automati­
cally when it becomes too hot from the
over load . T he
l§1 indicator light turns on

Automatic transmission
Shifting manually (tiptronic mode)
Applies to vehicles: with S tronic transmission/ shift paddles
The tiptronic allow the driver to shift the gears
manually .
Fig. 84 Center conso le : manual shift in g with the selector
l ever
Fig . 85 Steer ing wheel: manual shi ftin g with the shi ft pad­
dles•
Shifting with the selector lever
You can shift into tiptronic mode while stationary
and while driv ing.
• To shift into tiptronic mode, push the selector
lever from the D/S setting to the right in the
tiptronic shift gate. Once the transmission has
switched modes, the selector lever position
M
is shown in the instrument cluster display
¢ page 89, fig. 81. For example M4 , means the
fourth gear is engaged .
• To sh ift up a gear, tap the se lector lever for­
ward
0 ¢ fig. 84.
• To shift down a gear, tap the selector lever to
back Q.
Shifting with the shift paddles*
You can operate the shift paddles in the D/S or M
(tiptronic shift gate) selector lever positions.
94
.,. To shift up one gear, tap the shift paddle 0
¢fig. 85 .
.,. To shift down one gear, tap the shift paddle Q.
If the shift paddles are tapped wh ile in the D/S
selector lever position, automatic mode switches
off briefly. To switch from manually shifting back
to automatic shifting immediately, tap the sh ift
paddle
0 ¢ fig. 85 for 1 second.
To keep shifting using the shift paddles, move
the selector lever to the right out of the D/S posi­
tion into the tiptronic shift gate.
The transmission automatically shifts up or down
before critical engine speed is reached.
The transmission only allows manual shifting
when the engine speed is with in the permitted
range.
(j) Tips
- If you shift to the next lowest gear, the
transmission will only shift if the engine will
not be over-revved.
- With kick-down, the transmission shifts to a
lower gear, depending on vehicle speed and
engine speed.
- ti ptronic does not work if the transmission
is running in emergency mode.
. Kick-down
Applies to vehicles: with S tronic transmission
Kick-down enables maximum acceleration.
When you press the accelerator pedal down be­
yond the res istance point, the automatic trans­
mission downshifts into a lower gear, depending
on veh icle speed and engine RPM. It shifts up in­
to the next higher gear once the maximum speci­
fied engine RPM is reached.
A WARNING
Please note that the whee ls cou ld spin on
slick or slippery roads when kick-down is ac­
tive.
-

,....,
N
0 > co ,...., Launch Control-Program
Applies to vehicles: with launch control
The Launch Control Program enables maximum
acceleration .
Requirement: the engine must be at operating
temperature and the steering wheel must not be
turned .
.. With the engine running, press the
l~OFF ! but­
ton briefly one time
ll .
.. Pull the selector lever back out of the D/S posi­
tion briefly to select the S position, or press it
toward the right into the tiptronic pos ition or
select the
D ynami c driving mode in drive se­
lect*
~page 148.
.. Press the b rake peda l firmly wi th you r left foot
and hold it all the way down for at least 1 sec­
ond.
.. At the same time, press the gas pedal all the
way down with your right foot until the engine
reaches and stays at a high RPM level.
.. Remove your left foot from the brake.
A WARNING
-Always adapt yo ur driv ing to the traffic flow.
- Only use Launch Control when road and traf-
fic cond itions allow it and other dr ivers will
not be endangered or impacted by you r d riv­
ing and the vehicle's accele ration.
- Please note that the drive whee ls can sp in
and the vehicle can break away when sport
mode is swit ched o n, especia lly when the
road is s lippery.
- Once t he vehicle has sta rted moving, press
the
I $? OFF ! button briefly to t urn the sport
mode off.
(D Tips
- The transmiss ion temperature may increase
s ignificantly after using the lau nch cont rol
program.
If that happe ns, the program m ay
l) In vehicles w ith a d river information system, an ESC light
in the instrument cluster stays o n continuous ly and the
message
Stabili za tion contro l (E SC ): sport . Warning! Re·
stricted st abi lity
appears temporar ily.
Autom atic tran sm iss ion
not be ava ilab le for a few minutes. It will be
avai lab le again after a cool-down period.
- Whe n accelerating using the launch contro l
program, all vehicle parts a re su bject to
heavy loads. This can lead to increased
wear.
Emergency mode
Applies to vehicles: wit h S tronic transmiss ion
In the event of o system mo/function, there is on
emergency program.
If all of the selector lever positions are hig hlight­
ed with a light background in the instrument
cluster disp lay, there is a system malfunction and
the S tronic transmission is running in the emer­
gency program. The vehicle can still be driven in
emergency mode, but only with reduced speed
and not in all gears . In some cases, the vehicle
cannot drive in rever se .
(D Note
If the transm ission runs in emergency mode,
drive to an authorized A udi dealer or author­
iz ed Audi Se rvice Facility immed iate ly to have
the malfunc tion corrected.
Transmission malfunction
• Tran smi ssion malfunction ! Pl ea se stop the
vehicle and select P
The re is a ma lfunction in the transmission. Park
the vehi cle secure ly and do not cont in u e driv ing.
See a n author ized Audi dealer or au thori zed A udi
Service Facility for assis tance.
• Tran smission overheating! Plea se stop the
vehicle!
The transmiss ion is too hot and can become dam­
aged. Stop and let the transmiss ion cool w ith the
engi ne r unning (at idle) in the P se lector lever po­
s it ion. Then the ind icator lig ht and the message .,.
95

Automatic transmission
turn off, drive to an authorized Audi dea ler or au­
thorized Audi Service Facility immediate ly to have
the malfunction corrected . If the ind icator light
and the driver message do not turn off, do not
continue driving. See an authorized Audi dealer
or authorized Audi Service Facility for assistance .
rm Transmission malfunction: you can continue
driving
Drive to an autho rized Audi dea ler or authorized
Audi Service Facility immediately to have the
malfunct ion corrected .
rm Transmission malfunction: no reverse gear
(you can continue driving)
Drive to an authorized Aud i dea ler or authorized
Aud i Service Facility immediately to have the
malfunct ion corrected.
[O] Transmission malfunction: You can continue
driving in D until engine off
Drive the vehicle away from moving traffic and
park. See an authorized Audi dealer or authorized
Audi Service Facility for assistance .
rm Transmission overheating! Please adapt
driving style
Continue driving moderately. When the indicator
light turns off, you can continue driving normal­
ly .
rm Transmission: Press brake pedal and select
gear again.
If the transmission malfunctions because the
temperature is too high, a message appears
when the transmission is cooled.
96
Selector lever emergency release
App lies to vehicles: wit h S tronic transmission
If the vehicle's power supply fails, the selector
lever can be released in an emergency.
Fig. 86 Se lector leve r: remov ing the cover
Fig. 87 Selector lever: us ing the emergency release to
move out of the Pa rk posit ion
The emergency release mechanism is located in
the right area under the selector lever shift gate.
Using the emergency release can be complicated.
We recommend contacting an authorized Audi
dealer or authorized Audi Service Facility for as­
sistance, if necessary .
The screwdr iver from the vehicle tool kit located
i n the luggage compartment is needed to for the
eme rgency release¢
page 280 . Use the flat side
of the reversible screwdriver blade.
Removing the selector lever cover
.,. Set the parking brake(®)¢,& to secure your
vehicle from rolling .
.,. Insert the flat side of the screwdriver s ideways
in the slot near the s hift cover and pry the shift
cover up
¢ fig. 86 .
.,. Pull up the corners of the shift cover carefully
with your hands and fo ld it over the shifter
knob
¢ fig . 87. ..,.

,....,
N
0 > co ,...., injuries. When the vehicle enters drive ready
mode, the status message
e-"'1 o I r.-.Al"'Y ap­
pears briefly in the instrument cluster display
and the needle in the power meter points to
READY ¢page 101.
-Make sure that the selector lever is in the P
position and the ignition is switched off
when leaving the vehicle.
([) Note
-The high-voltage system can be damaged if
the vehicle underbody comes into contact
with the ground. Immediately drive your ve­
hicle to an authorized repair facility and
have it inspected.
- The electric drive motor can become very
hot during operation . Do not stop the vehi­
cle if there is oil, fuel residue or other flam­
mable substances under or next to the vehi­
cle.
Special considerations for the high-voltage
battery
Please first read and note the introductory infor­
mation and heed the warnings
¢page 98.
All batteries age with use and over time. There
are things you should know about the care of the
high-voltage battery that will help it keep giving
you good service and reliability over time. Please
read and keep the following information in mind
while you enjoy the performance and economy of
your vehicle.
- Be sure to charge the high-voltage battery be­
fore leaving the vehicle parked and unused for a
longer period of time. Ideally the high-voltage
battery should have a charge level between
40% and 60% when parked for a long time.
- If the battery charge level is below 3%, never
park the vehicle for more than 21 days without
charging the high-voltage battery. Should you
have to park the vehicle for a long time, make
sure that the charge level is sufficient to help
prevent the battery from aging prematurely.
- Frequent and consecutive charging of the high­
voltage battery when the charge level is above
98% can also decrease the capacity of the high-
e-tron
voltage battery. Make sure the charge level is
below 98% when you start the charging proc­
ess.
- Should the vehicle be parked for longer than
2 days at temperatures below -13 °F (-25 °(),
the high-voltage battery could freeze and not
be able to provide energy to the electric motor.
The battery will start working again, once it
warms up . The battery can be warmed up when
the outside temperature rises or when the vehi­
cle is garaged appropriately. The battery will al­
so warm up when being used (switching on the
air conditioner, the heater or by driving the ve­
hicle). Should you have to park your vehicle at
very low temperatures for longer than 1 day,
make sure that the high-voltage battery does
not freeze by parking the vehicle in a garage
that is heated or protected from the outside
temperature.
- The high-voltage battery can be damaged and
the capacity can be decreased when the vehicle
is parked for longer than 24 hours when the
ambient temperature is higher than 118 °F
(48 °C). Always make sure that the high-volt­
age battery is not exposed to temperatures
above 118 °F (48 °C) for a long time.
- Never park the vehicle in areas that are likely to
be flooded, such as beaches or river banks, and
never drive the vehicle in WATER, on flooded
roads or through water that is higher than the
bottom of the vehicle body. The high-voltage
battery, along with other vehicle components,
can be damaged severely if the high-voltage
battery is exposed to open water especially for
a longer time. However, you can drive through
water on roads under certain conditions
¢ page 77, Driving through water on roads .
Failure to heed any of these requirements can
age the battery prematurely and lead to a perma­
nent decrease of the high-voltage battery's ca­
pacity.
(D Tips
Always make sure that the high-voltage bat­
tery is not exposed to extremely low and high
temperatures as well as to water especially
for a longer time. Failure to protect and care
for the high-voltage battery can lead to
99

.... N
0 > CX)
.... I.Cl U"I
.... I.Cl ....
e-tron
Power meter overview
Applies to vehicles: with plug-in hybrid drive
The power meter shows the status of the plug-in hybrid drive and the availability of the plug-in hybrid
system .
Fig. 88 Power m ete r overview
When opening the driver's door, the charge level
is shown in the inst rument cl uster when the igni­
tion is sw itched on, or the cha rge level and the
rema ining charge time for the high-vo ltage bat­
tery is displayed when charg ing .
The power mete r is located in the instrument
cluster in place of the tachomete r. A d igital tach­
omete r can be d isplayed in the driver info rmation
sys tem
¢ page 29 .
The power mete r gives feedback about the part ic­
u lar accelerator pedal position and shows the
current demand
(%) for electricity or fue l regard­
less of which engine is active.
An economical dr iv ing and recupe ration range is
shown in g reen
¢ page 104, Energy recovery (re­
cuperation) .
A driving range that is not economi­
cal is shown i n orange . In add ition, the batte ry
status provides information about the high -vo lt ­
age battery charge status.
(D Vehi cle no t drive ready (OFF)
@ Recuperation (CHARGE)
® Veh icle dr ive ready (READY)
@ E ff ic ient driving w ith electric moto r
and/or gasoline engine (E FFIC IEN­
CY)
® E conom ic driving wh ile the electric
moto r or gaso line engine is in the
partia l powe r range
® Driving in fu ll power range
(J) 100% output
@ Boos ting -the e lec tric mo tor as­
sists the gaso line engine (BOOS T)
® High-voltage battery charge level
@ T he EV mode is ac tive o r EV mode is
current ly not ava ilable
@ Speed limit for electric driving in EV
mode (80 mph/ 130 km/h)
Indicator lights and messages
Applies to vehicles: wit h plug-in hybrid drive
Also note the ind icator lights in ¢ page 13.
The gasoline engine is act ive when the Ill indica ­
tor light t urns on.
• Drive system : sy stem fault! Safely park vehi­
cle
T he re is a ma lfunction in the plug- in hybrid sys­
tem. The br ake booster and the power steer ing
may stop working . Stop the vehi cle immed iate ly
or as soon as possible. Park the ve hicle in a sa fe
place outdoors that is not near bu ildings, roof ..,_
101

e-tron
Setting plug-in hybrid drive modes
Applies to vehicles: w ith p lug -in hybrid drive
Fig. 90 Center console : but ton &
You can change modes when the vehicle is sta­
tionary or while driving. If the vehicle operating
conditions will not allow you to set the mode manually, the last active mode is se lected .
.,. Press the
laV I button repeatedly until the de­
sired mode is displayed in the instrument clus­
ter . Or :
.,. Select the mode in the MMI
n: press the
I MENU I function button> Car > Systems con­
trol button >
e-tron mode and select the de­
s ir ed mode .
The active mode is displayed the first time the
14 "1
button is pressed .
Plug-in hybrid functions
Applies to veh icles: with p lug -in hybrid drive
The functions described below activate automati­
cally depending on the driving style.
Full acceleration (boost)
The boost funct ion is act ivated by pressing the
accelerator pedal farther down (kick-down). The
l) Not availa ble in a ll Info ta inm en t sy ste m s.
104
vehicle is powered by both the gasoline eng ine
and the e lectric motor when in fu ll acce leration.
Boost is only ava ilable for a short time because it
uses a large amount of energy. Availability de ­
pends on the high-voltage battery charge level.
Coasting
The gasoline engine switches off and disengages
at speeds up to approximate ly 112 mph
(180 km/h) if the acce lerator pedal is not press­
ed and the D position is selected. Driving conser­
vatively like this can reduce fuel consumption .
Energy recovery (recuperation)
When braking, the electric motor will act as a
generator creating electric energy that is then
stored in the high-voltage battery . This also oc­
curs when the vehicle is coasting or driving down­
hill.
If the brakes are applied early and evenly, the electric motor w ill brake the vehicle @
¢page 101 , fig. 88. By doing this , a large
amount of the kinetic energy is recovered and
may be stored as e lectric energy in the high -volt ­
age battery . The conventional brakes are also ac­
tivated when the brakes are pressed very hard.
The strength of recuperation can depend on the
following factors:
- If you are in tiptronic mode
Q page 94 . Or
- If the sport driving mode 5 was selected.
The ene rgy recovery is shown in the energy flow
i ndica tor in the in str ument cluster display
¢page 106 .