charging AUDI S3 SEDAN 2018 User Guide

e-t ro n
The vehicle tool kit and the tire mobility kit (Tire
Mobility System) are located in the side trim pan­
el @ and ® in the luggage compartment.
Addit ional info rmation about the vehicle tool kit
may be found under ¢
page 360 and informa­
tion about the tire mobility kit under
¢ pag e 361.
@ Tips
The vehicle must not be operated without the
tire repair set.
Vehicle transport
A ppl ies to: ve hicles w ith p lug- in hybrid drive
The following contains information you should
know about transporting your vehicle .
The MQB-A high-voltage lithium -ion battery sys­
tem equ ipped in yo ur vehicle is composed of SA­
NYO 12 UF 261 591 h igh-vo ltage batteries and
has passed test 38 .3 in accordance with the UN
Tests and Criteria handbook . The vehicle may be
transported with the high-voltage battery instal­
led as conventional class 9 ha zardous materials
without additional official consent for air and sea
sh ipment (current law ICAO-TI and IMDG-Code
01.01.2012) .
Jump start
App lies to: ve hicles w ith plug -in hybrid drive
The term "vehicle battery " refers to the 12 Volt
battery in your vehicle.
F ig . 1 05 Eng in e co mpartment: conn ectors for a c harge r
and jump star t cables
The vehicle is equipped with one vehicle battery
and one high-voltage battery .
102
If the vehicle battery is drained, it can be charged
with a charger or you can jump start the vehicle us ing another vehicle's battery in the same way
as a conventional vehicle.
Read the information about charging the vehicle
battery ¢
page 32 7 and for jump starting the ve­
hicle
¢ page 375 .
.,. Open the hood ¢ page 320.
.,. Remove the fuse box cover @ to access the
positive terminal
0 ~ page 321.
.,. Clamp the terminal clamps from the charg ing
device or jump start cable to the positive termi­
nal
0 and to the body ground point Q .
@ Note
You must not give a jump start with your vehi­
cle . Th is cou ld cause s ignificant damage to
the electrical system i n your vehicle .
Coolant
Applies to: vehicles wit h pl ug-in hyb rid drive
Fig . 106 En g in e compartment: coolant exp ans ion tank
Your vehicle has two coolant expansion tanks
that are separate from each other:
@ : expansion tank for gasoline engine and elec ­
tric motor .
@: expansion tank for the high -vol tage area.
The expan sion ta nk @ must not b e opened
¢,& .
.,. Switch the ignition off.
.,. Open the hood ¢ page 320.
.,. Always check the coolant level in both coolant
expansion tanks @ and @ using the outer
ma rkings.
1111>

e-tron
The gaso line engine is no longer ava ila b le be ­
cause there is not enough fue l. Drive immediate ly
to a gas station.
Fuel filler door emergency release
A pp lies to : ve hicles w ith plug- in hybrid drive
You must use the emergency re lease to open the
fue l filler door when there is a malfunct io n
c::;, page317 .
The tank is not vented. You can only f ill a small
amount of fuel in the tank.
~ Fill only unti l the automatic fue l pump nozzle
turns off for the first time when it is operated correctly.
Drive to an a utho rized Aud i de aler or a uth o rized
Audi Service Facility immediately to have the
malfunctio n corrected .
(D Tips
Pressure can escape if you open the tank ca p
after using the emergency release . This can
create noises.
Charging
General information
A pp lies to: ve hicles w ith plug -in hybrid drive
Two options are ava ilab le for cha rging the vehi ­
cle:
- Charge at a p ublic charging stat ion w ith a spe­
c ia l charging cable*
c::;, page 106 .
-Charge with ho useho ld and industrial power
sockets using the Audi e-t ron c harg ing system
¢ page 106.
Environmental condition s when using the
Audi e-tron charging system
- Operat ing temperatu re : -13 °F (-25 °C) to 95 °F
(+35 °C)
- Humidity: 5% to 95%, non-co ndensing
- 13,000 feet (4,000 meters) maximum above
sea leve l
- Protected against dust and spray (IP54 (USA:
enclosure 3 R))
104
Warnings when using the charging system
&
Surfaces ca n become very hot when
i n d irect su nlight .
&~
Incorrect use increases the risk of
electric shock.
~¼
Do not use any extens ions co rds o r
c abl e reels.
~
Do not use any travel adapters.
~~
Do not use any power str ips.
~~~
Do not use any charg ing cables with
damage to the electronics or the
con necti ng w ires .
.&_ WARNING -
Sockets that are inst alled incorrect ly can
cause elect ric shock or fire when charging the
h igh -vo ltage battery using the vehicle charg ­
ing connection .
- Installation and set up of the household con­
nection for the Audi e-tron charging system
may only be performed by a qualified e lec­
trician. The q ualified electrician is thereby
fully responsib le for adhering to applicable
standards and regu lations.
- Make sure that the selected charg ing con­
nection is suitable for drawing 16 amps .
- Make sure that the household soc ket is
grounded and shielded from water.
- The A udi e-tron charging system may only
be used with a prope rly grounded power
network. It cannot be used with non­
gro unded power networks (s uch as IT net­
wo rks) .
- Please follow the safety precautions in the
assembly instr uctions for the A udi cha rging
dock* or the Audi cha rging clips* .
.&_ WARNING
If you are not fam il iar with the socke t or the
e lectr ica l installation or it has not been
checked by qualified e xperts, never use i t fo r
cha rging. Even very low ch arg ing cu rrents can
cause ser ious damage and in particular fires if
the socket or electrical installation is in bad
Ill>

u. 00 .-< N l'­ N .-< 0 N > 00
condition. If necessary, get expert assistance
from a qualified electrical installation special­
ist.
A WARN ING
Incorrect handling of the connector contacts
can cause electric shock or fire.
- Do not touch the contacts for vehicle charg­
ing port and for the Audi e-tron charging
system .
- Do not insert any objects in the vehicle
charging port or in the Audi e-tron charging
system .
- Protect the sockets and connectors against
any moisture, water and other fluids .
A WARNING
Using a damaged or incorrect charging cable
or a damaged or incorrect socket, using the
Audi e-tron charg ing system incorrectly or
disregarding the safety precaut ions could
cause short circu iting, electric shock, explo ­
sions, fires and burns .
- Do not use the Audi e-tron charging system
if it is damaged and/or dirty . Check the ca­
ble and connector for damage and dirt be­
fore using.
- T he Audi e-tron charging system must only
be connected to sockets that are installed
correctly and that are not damaged as well
as to electrical installations that have no
faults.
- Do not use any extension cords, cable reels,
power strips or (travel) adapters.
- Disconnect the Audi e-tron charging system
from the power network during a thunder­ storm.
- Do not modify or repair any electrical com­
ponents.
- Never immerse the Audi e-tron charging
system and connectors in water.
- The Audi e-tron charging system must only
be cleaned when the control unit is com­
pletely disconnected from the power supply
and from the vehicle. Use a dry towel to
clean .
e-t ron
-If a 110 volt household socket is used for
charging, only connect one vehicle at a time
to the same circuit. Use a different circuit if
an additional vehicle needs to be charged at
the same time. Note the maximum permit­
ted current draw for the circuit . Contact a
qualified electrical technician if there is any
doubt .
A WARNING
The components in the Audi e -tron charg ing
system can trigger sparks which can cause
flammable or explosive fumes to ignite.
- To reduce the r isk of exp losions, espec ially
in garages, make sure the contro l unit is at
least 19 inches (SO cm) above the floor
when charging.
- Do not use the Audi e-tron charging system in areas at risk for exp losions .
- The Audi e-tron charging system is only suit­ ed for use on Audi vehicles and vehicles
within the Volkswagen Group . Using the de­
vice on vehicles made by another manufac­
turer is not authori zed.
@ Note
Make sure that you always use the suitable
power plug provided with the Audi e-tron
charging system for the corresponding mar­
ket. Contact an authori zed Audi dealer or au­
thorized Audi Service Facility for more infor­ mation .
(D Tips
-Only use the factory-provided charging ca­
ble from Audi or the Volkswagen Group to
charge your vehicle .
- For an uninterrupted charging process, we
recommend only charging using sockets
that are connected to a separately protect­
ed circuit .
- Using either NEMA sockets with a current
rating of at least 30 A or industrial sockets
in accordance with IEC 60309 when charg­
ing is recommended.
1 05

e-tron
-When charging the high-vo ltage battery us ­
ing househo ld/industrial sockets, the elec­
trical installat ion can be used at full capaci­
ty. Having a qualified electrician regularly
inspect the electrical installations that are
used for charging is recommended.
- The vehicle radio and TV systems may have
limited reception when charging the vehi­
cle .
Charging at public
charging stations
Applies to: vehicles with plug-in hybrid drive
Use the charging cable supplied at the public
charging stat ion for charging. Contact an author­
ized Audi dealer or authorized Aud i Service Facili­
ty for more information.
• Follow the operating instr uctions at the charg­
ing station to charge the high-vo ltage battery .
• Unlock the vehicle if necessary ¢ page 31.
• Make sure that the selector lever is in the P po ­
sition and drive ready mode is switched
off.
• Turn the lock until it is vertical to open the cov­
er on the charging unit <:!;> page 110 , fig . 117.
• Slide the cover carefully to the side if necessa­
ry .
• Remove the lock on the charg ing port
<:!;>page 110, fig . 118.
• Remove the cap from the charging cable.
• Connect the cable to the veh icle charging port .
• If a charging timer is not set, the charging
process will start automatically depending on
the charging station
¢ page 110, Setting the
charging timer.
• The vehicle operating status is indicated by the status
LED @¢ page 109, fig. 116 or q table
on page 113 .
• Also read the information found in
<:!;>page 112, After charging .
(J) Tips
Only charge your vehicle at charging stations
that conform to the follow ing standards, de­
pending on the co untry:
- GB/T 18487 .1 and GB/T 20234 (China)
- IEC 61851 and IEC 62196 (Europe)
- SAE Jl 772 (North America, Japan)
106
@ Tips
-It is not possible to charge using the charg­
ing timer at some charg ing stations.
- You can use your Audi e-tron charging sys­
tem if there is a househo ld or industrial con­
nection available at the charging station.
Charging the battery
with the Audi e-tron
charging system
Charging system overview
Applies to: vehicles with plug-in hybr id drive
Fig. 109 A udi e-tro n charging sys te m overv iew
@ Power cable
@ P ower pl ug (for industrial sockets)
© Power plug (for household sockets)
@ Control unit
® Vehicle charging connector (connector for the
vehicle)
® Veh icle cable
The power cable @ is plugged into the upper end
of the control unit and the vehicle cable ® is
pl ugged into the lower end of the control unit @.
(D Note
The charg ing system can be operated within a
temperature range of-13
°f (-25 °C) to 95 °f
(+35 °C). Note the following information:
- Protect the charg ing system against any
st rain, such as being run over, falling, pull-
ing, bending and crushing.
Ill-

LL co ..... N
" N ..... 0 N > co
-Using the control unit while operating the
charging dock*
c;, page 108 or charging
clip*
c;, page 108 is recommended .
-Do not immerse the control un it in water or
cover with snow or ice.
(D Tips
-Always place the Audi e-tron charging sys­
tem on a secure surface when charg ing.
-To reduce the risk of overheat ing during op­
eration, do not place the Audi e -tron charg­
i ng system in direct sunlight for long peri­
ods of time.
-If the temperature inside the control unit rises above 176 °F (80 °C), the charging
process will stop automatically unti l the
temperature decreases back down to the normal range.
Changing/attach ing the power/vehicle
cable
Ap plies to: ve hicles with p lug -in hybrid drive
Fig. 110 Co ntro l u nit: remov ing/attac hing the cable
Requirement s:
.,. The charging process for the h igh-voltage bat­
te ry must be ended .
.,. The veh icle charg ing connector m ust be re­
moved from the veh icle charging port.
.,. The power cable must be removed from the
socket.
Loo sening the cable
.,. If necessary, loosen the screw @ c;, fig. 110 us­
ing the screwdriver provided.
.,. Lift the lever CD a ll the way up.
.,. Pull the connector @out just until you fee l re­
sistance.
e-tron
.,. Close the lever CD until it is resting on the con-
nector @.
.,. Remove the connector @completely.
Attachin g the cable
.,. Lift the lever CD up slight ly.
.,. Insert the connector @ into the control unit
just until you feel resistance .
.,. Lift the lever CD all the way up.
.,. Insert the connector@all the way into the
control un it.
.,. Close the lever CD -
.,. Tighten the screw @ using the screwdriver pro­
vided.
A WARNING
-Always remove the power cable from the
socket before changing the power cab le or
veh icle cable.
-Always follow the instructions given when
charging the high-voltage battery. Do not remove the vehicle charging cable from the
socket during the charging process. End the
charging process before removing the vehi­
cle charging cable from the socket.
-Only change cab les in a dry environment.
-The Audi e-tron charging system may only
be used as one unit composed of power
ca­
b les, the control unit and vehicle cable. We
recommend using on ly cables approved by
Audi.
-
107

e-tron
Charging dock
Applies to: vehicle s with plug-in hybrid drive and charging
dock
F ig . 111 Opening/clos ing t he charg ing dock
®
Fig. 11 2 Chargi ng dock : mount ing th e c harging sys te m
You can store the charg ing system in the charg ­
ing dock.
Opening /closing the charging dock
.. If necessary, you can u nlock/lock the charg ing
dock using the key provided by turning it to the
unlocked position @ or locked position @
¢fig. 111 .
.. Opening/closing the door on the charging dock.
Mounting the charging system in the
charging dock
.. Open the door on the charging dock.
.. First insert the control unit in the bottom tabs
on the charging dock and then into the upper
tabs.
.. Push the control un it toward the rear and let it
lock into place .
.. Guide the vehicle cable th rough the opening @
¢fig. 112.
.. Wrap the extra c ab le length around the adapt­
er @ .
.. Plu g the power cable into the socket in the
charging dock .
108
.. Close the door.
.. After charging, you can p lace the vehicle charg­
ing
connecto r@ ¢page 106, fig . 109 in the
holder on the charging dock
door¢ fig. 111.
Removing the charging system from the
charging dock
.. Open the door on the charging dock .
.. Remove the power cable connector from the
socket in the charging dock .
.. Unwrap the cable from t he adapter @ .
.. To loosen the control unit from the holder,
press the re lease tabs above the cont rol un it @
¢ fig. 112 .
(D Tips
-Always keep the door on the cha rg ing dock
closed .
- Do not place any objects on the doo r or the
charging dock.
Charging clip
Applies to: vehicles with plug-i n hybrid drive a nd charging clip
Fig . 113 Cha rg in g clip: c harg ing syste m connected
Connecting the charging system to the
charging clip
.. First insert the co ntro l unit in the bottom tabs
on the charging clip and then into the upper
tabs .
.. Push the con trol uni t towa rd the rear -ar row­
¢ fig . 113 and let i t lock into place .
.. Wrap the extra cable length aro und t he charg­
ing connector mount
(D.
.. Plug the power cable into the socket @ .
.. After charging, you can hook the vehicle charg­
ing
connector ©¢ page 106, fig. 109 to the
charging connector mo unt
(D ¢ fig . 113. .,.

LL co ..... N
" N ..... 0 N > co
Removing the charging system from the
charging clip
.,. Remove the power cable connector from the
socket @ .
.,. Unwind the cable from the charging connector
mount (D .
.,. To loosen the control unit from the bracket,
push the lock ing mechan ism @ upward
9fig. 113.
Transporting
Ap plies to: veh icles with plug-in hybrid drive
Fig. 114 Storage bag
.,. Store the charg ing system and the special
charg ing cable* in the bag befo re transporting .
.,. Secure the bag using the tie-downs¢ page 64.
The flat hook must be secured to the left side
of the tie-downs.
& WARNING
-If the vehicle charging cab le is not secured
or positioned correctly, it can slide out of
place and endanger vehicle occupants when
brak ing, when changing directions, or in an
accident.
- Never transport the Audi e-tron charging
system or the special charg ing cable" unse­
cured.
- Store the Audi e-tron charging system or the special charging cable* in the storage
bag in the luggage compartment.
- Always transport the storage bag in the lug­
gage compartment and never in the passen­
ger compartment (for example the seats or
in front of them) .
e-tron
Charging overview
Applies to: vehicles with plug -in hybrid drive
Fig. 115 Charging system : control unit
Fig . 116 Radiator grille: veh icle charg ing port and bu tto n
mod ule
The charging unit is located behind the Audi rings
on the front of the vehicle .
@ ~ Button/LED
® Display field
© Arrow buttons
@IOK I Button
(D Charging timer button
@Status LED
@ Immediate charging button
T he meaning of the different status displays for
the charging sys tem and the vehicle can be found
un der
9 page 112, Status displays.
A WARNING
There is an error in the control unit if the LED
@is red. Disconnect the control unit from the
power supply . Refer to th is chapter
¢page 112, Status displays. llll-
109

e-tron
@ Tips
-The device runs a self test after power has
been restored to the control unit.
- You can activate a PIN for the control unit
¢page 115.
-The vehicle cannot be started if a charging
connector is connected .
Before charging
Applies to: vehicles w ith p lug- in hy brid drive
Fig. 117 Radiator grille: opening the charging unit cover
lll
~;:::;::.::.=;;.;;;:;;: --------- !
Fig. 118 Radiator grille: charging port cap
.. Unlock the veh icle if necessary¢ page 31 .
.. Make sure that the selector lever is in the P po ­
sition and drive ready mode is switched off
¢page 94 .
.. Turn the lock until it is vertical to open the cov­
er on the charging
unit ¢ fig. 117.
.. Slide the cover carefully to the side if necessa­
ry .
.. Remove the lock on the charging port
¢fig. 118.
.. Insert power plug @ or© into the socket
¢page 106, fig. 109 .
ll Not availab le in a ll Infotainment systems.
110
.. Plug the vehicle charging connector ©
¢ page 106, fig. 109 into the vehicle charging
port
¢ fig. 118. The charging process starts au­
tomatically if no charging timer is set.
(D Tips
Remove ice and snow from the cover using a
hand brush and solvent-free deicing spray.
Charging
Applies to: vehicles wit h pl ug -in hybrid drive
You can switch between the immediate charging
@ and charging timer fig. 116 during the charging process if a charging
timer was set . Press the desired button to do this
¢page 109, fig. 116.
You have different charging options:
Immediate charging
To start the charging process immediately, press
the
button @¢ page 109, fig. 116 . The LED in
the button turns on.
Setting the charging timer
You can delay the charging time with the charg­
ing timer in the Infotainment system
1>. You can
set two different timers .
.. If a timer was already set, press the button @
i:!.> page 109, fig. 116. The LED in the button
turns on.
.. To set a charging timer, select: I MENU ! button >
Vehicle > left control button > Charge > right
control button
> Program timer.
.. Select Individual timer or Repeat timer.
.. Set the departure time, the date or day of the
week .
.. You can specify a preferred charging t ime with
the charging timer, for example if you would
like to use the off-peak rate.
.. You can activate the auxiliary air conditioning
with the charging timer while charging by se­ lecting
Air conditioning with the control knob. ..,_

u. 00 .-< N l'­ N .-< 0 N > 00
A./ appears in the box. This activation is sepa­
rate from the Infotainment system settings in
the climate control menu
¢ page 116.
~ Press the I BACKI button.
~ To activate the desired timer, confirm the set­
ting with the control knob.
A,/ appears in the
box .
Power save mode
Power save mode is automatically switched on
when the control unit has not been operated for
more than one minute. The
LEO @¢ page 109,
fig. 115 stays on. All other displays turn off.
~ To switch power save mode on or off, press the
~ button @¢page 109, fig. 115.
Power save mode ends automatically when the
vehicle charging connector is plugged into the ve­
hicle.
The high-voltage battery is charging when the
LED@ blinks.
(D Tips
-Auxiliary climate control is powered electri­
cally if you select climate control using the
charging timer. This may also be used in
confined spaces such as garages.
- Using the auxiliary air conditioning while
charging can also reduce the charge level of
the high-voltage battery.
- The high-voltage battery also charges in
power save mode.
- If the charging process is in progress, it will
not be interrupted when power save mode
switches on.
- The charging process can be interrupted at
any time. Press the active button on the ve­
hicle to do this
¢page 109, fig. 116.
-The climate control output while charging
depends on the capacity of the electrical
connection. Additional information on cli­
mate control can be found under
¢page 116.
e-tron
Setting the charging power level
App lies to : veh icles w it h pl ug-in hybr id drive
The control unit automatically recognizes the
voltage and the available current strength. You
can set whether you would like to charge with the
full or half of the charging power.
~ Press the I OKI@ ¢ page 109, fig. 115 button
on the control unit.
~ Enter the PIN if necessary.
~ POWER and SET PIN appear in the display
field.
~ Select POWER with the arrow button @.
~ Press the I OK I button @.
~ The charging power display appears. The cur­
rent set value (50% or 100%) is marked with a
frame.
~ If necessary, change the setting using the ar­
row button © to move downward or upward.
~ Press the I OK I button @.
(D Tips
- If a household socket is used for the charg­
ing process, the charging power level is au­
tomatically set to 100%. If multiple electri­
cal consumers are connected to a circuit
'
the charging power may be limited to 50%
when charging with a household socket in
order to relieve the load on the electrical in­
stallation.
- If an industrial socket is used for the charg­
ing process, the charging power level is au­
tomatically set to 50%. To receive the maxi­
mum charging power, the value must be set
to 100% .
- A selected value remains set until the power
cable is connected again.
111

e-tron
After charging
A pplies to: ve hicles w ith p lug -in hybrid drive
Unlocking the vehicle charging connector
.,. Press the rele ase (i) ¢fig.119 .
.,. Remove the veh icle charg ing conne ctor @.
Closing the charging unit
.,. Put the cap back on the charg ing port
¢ page 110, fig. 118 .
.,. Carefully slide the cove r bac k in i ts or igina l po­
si tion .
.,. Tu rn the lock to the hor izonta l position
¢ page 110, fig . 117.
Fig . 119 Rad iator g rille : unl ocking a nd re mov ing the ve hi­
cle c harg ing connector
(D Note
Af ter com pleti ng the ch arging or climat e control
p rocess, t he vehicle enters a sleep mode . No d is ­
p lays are visib le on t he cha rging unit dur ing this
pe riod . I
f yo u drive with an o pen charg ing unit, both
the cover and the electronics installed behi nd
i t co uld be damaged .
(D Tips
Deactivating sleep mode
.,. Unl ock the ve hicle ¢ page 31 . Or
.,. Open the driver's door. Or
.,. Press t he button @¢ page 109, fig. 116 .
Status displays
App lies to: ve hicles w ith p lug- in hybrid drive
The ins trumen t clu ster will show if the charg­
ing unit is open. However, please check if the
cover is locked befo re every trip after cha rg­
i ng .
You can check the va rious ope rating statuses us­
ing the LED @, the disp lay fie ld on the control unit
@
¢ page 109, fig. 115 and the status LE D
@¢ page 109, fig. 116 .
Charging system: control unit
Symbol Error code LED on the control
unit@
Blue Flashes
On
Green Flashes
Whi te On
330, 340 Red On
112
Mean ing
Self test
Cable inse rted correctly
Cable inserted and charg­ ing
Self test comple ted s uc­
cessfully, cab le is not con-
Solution
nected or is connected in- Insert the cable cor rect ly .
correct ly to the vehicle
charging port.
Cable inse rted incorrectly
or fau lty. Check the
cable and insert
i t co rrectly o r rep lace t he
cab le.
1)1,,