service indicator AUDI S4 2018 Owners Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2018, Model line: S4, Model: AUDI S4 2018Pages: 403, PDF Size: 66.81 MB
Page 13 of 403
a co .... N ,....
N .... 0 0
3 co
A WARNING
Do not assume the roads are free of ice based
on the outside temperature display . Be aware
that there may be ice on roads even when the outside temperature is around 41 °F (+5 °C)
and that ice can increase the risk of accidents.
@ Tips
- Depending on vehicle equipment, the in
strument illumination (needles and gauges) may turn on when the lights are off and the
ignition is switched on . The illumination for
the gauges reduces automatically and even
tually turns off as brightness outside in
creases. This function reminds the driver to
turn the low beams on at the appropriate
time .
- You can select the units used for tempera
ture, speed and other measurements in the
Infotainment system
c::> page 248.
- If your vehicle is stationary or if you are driv
ing at very low speeds, the temperature dis
played may be slightly higher than the ac
tual temperature outside due to the heat ra
diating from the engine .
- At temperatures below 41 °F ( +5 °C), a
snowflake symbol appears in front of the
temperature display
c::> A .
Coolant temperature indicator
The coolant temperature
display @c::> page 10,
fig. 3 or c::> page 10, fig. 4 only functions when
the ignition is switched on. To prevent engine
damage, please observe the following notes
about the temperature ranges.
Cold range
If only the LEDs at the bottom of the gauge turn
on, the engine has not reached operating tem
perature yet . Avoid high engine speeds, full ac
celeration and heavy engine loads.
Normal range
The engine has reached its operating tempera
ture once the LEDs up to the center of the gauge
turn on. If
the. indicator light in the instru-
Cockpit overview
ment cluster display turns on, the coolant tem
perature is too high
c::> page 30.
(D Note
- Auxiliary headlights and other accessories in
front of the cooling-air intake impair the
cooling effect of the coolant. This increases
the risk of the engine overheating during
high outside temperatures and heavy en
gine load.
- The front spoiler also helps to distribute cooling air correctly while driving. If the
spoiler is damaged, the cooling effect will
be impaired and the risk of the engine over
heating will increase . See an authorized
Audi dealer or authorized Audi Service Fa cility for assistance .
@ Tips
Diesel engines: due to the high efficiency of
these engines, the engine may not always reach operating temperature in cold outside
temperatures . This is normal and not a cause
for concern.
Engine oil temperature display and boost
indicator
App lies to : vehicles wi th engine o il temperatu re display/boost
indica tor
Appl ies to : vehicles wi th analog ins trumen t cl uster
The engine oil temperature and boost indicator
are only shown in the lap timer display
c::> page 106.
Engine oil temperature indicator
Applies to : vehicles wit h Audi v ir tu al coc kpit
The engine oil temperature is only shown in the
expanded view or in the sport view
c::> page 15.
When engine oil temperatures are low, the display--- °F
(---°C) appears in the instrument clus
ter.
The engine has reached its operating tempera
ture when the engine oil temperature is between 176 °F (80 °C) and 248 °F (120 °C) under normal
driving conditions. The engine oil temperature
.,,.
11
Page 27 of 403
fast acceleration) and have the malfunction corrected. See an authorized Audi dealer or
authorized Audi Service Facility .
The electronic speed limiter may be faulty if the
indicator light turns on. For additional informa
tion, see
¢ page 102, Electronic speed limiter .
The MIL indicator light may also turn on if the
fuel filler cap is not closed correctly
¢page 317.
On-Board Diagnostics
Fig. 22 Location of Data Li nk Con nec tor (DLC )
On-Board Diagnostics monitors the components
of your em ission control system. Each monitored
component in your eng ine system has been as
signed a code. In case of a ma lfunction, the com
ponent will be identified and the fault stored as a
code in the control module memory.
The MI L light may also illuminate if there is a
leak in the on -board fuel vapor recovery system.
If the light illuminates after a refueling, stop the
vehicle and make sure the fuel filler cap is prop erly closed (only vehicles with gasoline engine)
¢ page 317 .
In order to make an accurate diagnosis, the stor
ed data can only be displayed using special diag nostic equipment (generic scan tool for OBD) .
In order to connect the specia l diagnostic equip
ment, push the plug into the Data Link Connector
(DLC). The DLC is located to the right of the hood
release¢ fig. 22.
a Your authorized Audi dealer or qualif ied work-al
;:::: shop can interpret the code and perform the nee-
" ~ essary repair . 0 0
~ al
Cockpit overview
A WARNING
--
Do not use the diagnostic connector for per
sonal use. Incorrect usage can cause malfunc
tions, which can increase the risk of a colli
sion!
Indicator lights
Description
The indicator lights in the instrument cluster
blink or turn on. They indicate functions or mal
functions.
Messages may appear with some indicator lights.
A warn ing s ignal will sound at the same time.
The indicator lights and messages in the instru
ment cluster display can be covered by other dis
plays. To show them again, select the second tab
with the mult ifunct ion steer ing
wheel ¢ page 13.
If there are several malfunctions, you can display
them one at a time using the thumbwheel.
Some indicator lights in the display can display in
several co lors.
it Central indicator light
If the. or d indicator light turns on, check
the message in the instr ument cluster.
Overview
Some indicator lights turn on briefly as a function
check when you sw itch the ignition on. These sys
tems are marked with
a./ in the fo llowing tab les.
If one of these indicator lights does not turn on,
there is a malfunction in that system.
Your vehicle has either a monochrome display or
a multicolored display, depending on vehicle
equipment. Some indicator lights appear white
on a monochrome display .
The. or Q central
indicator light turns on at the same time to indi-
cate the priority of these indicator lights.
..,.
25
Page 31 of 403
If the indicator light turns on and this message
appears, there is a malfunction in the brake booster.
I f the ABS indicato r light
[I]) (USA mode ls) I
ti] (Canada mode ls), the ESC indicator light J.ft .
and the brake system indicator light 1111 (USA
models)
I . (Canada mode ls) all turn on and
this message appears, then the ABS, ESC and
braking distribution are malfunctioning
c::> ,&. .
Do not continue driving . See an authorized Audi
dea ler or authorized Aud i Serv ice Facility for as
sistance
c::> ,&. .
1111 (USA model s) /. (C anada mod els ) Pa rk
ing brake: malfun ction! Safel y stop vehicle . See
owner 's manu al
- If the indicator ligh t and the message appea r
when the vehicl e is stationar y or afte r switch
ing the ignit ion on ,
check if you can release the
park ing brake. If you cannot re lease the park
ing brake, see an authorized Aud i dealer or au
thorized Aud i Serv ice Facility. If you can release
the parking brake and the message still ap
pears, see an authorized Aud i deale r or author
ized Audi Service Facility immediately to have
the malfunction correc ted.
- If the indicator light and message appea r
whil e
dri ving ,
the hill start assist or emergency brak
ing function may be malfunctioning. It may not
be poss ible to set the pa rking brake or release
i t once it has bee n se t. Do not park your veh icle
on h ills. See an authorized Audi dealer or au
thorized Aud i Service Facility for ass istance.
Brake boo ste r: re stricted . You can c ontinue driv
in g. Ple ase co ntact Servic e
There is a malfunction in the brake booster. The
brake booster is availab le, but its effectiveness is
reduced. B raking behavio r may be diffe rent from
how it normally fu nctions and the b rake peda l
may v ibrate.
Drive to an authorized Aud i dealer or authorized
Aud i Service Faci lity immediately to have the
a malfunct ion corrected. co .... N ,....
N .... 0 0
3 co
Coc kpit o ve rv iew
A WARNING
-Read and follow the warnings in
c::> page 323, Working in the engine com
partment before opening the hood and
checking the brake fluid level.
- If the brake system indicator light does not turn off or it turns on wh ile driving, the
b rake fl uid leve l in the reservo ir is too low,
and this increases the risk of an accident.
S top the vehicle and do not continue d riv
ing . See an authorized Aud i dealer o r au
thorized Audi Service Facility for assistance.
- I f the brake system indi cator light turns on
together with the ABS and ESC indicato r
lights, the ABS/ESC regu lating function may
be malfunct ion ing. Funct ions that stabilize
the vehicle are no longer available. This
could cause the vehicle to swerve, which in
creases the risk that the vehicle will slide. Do not cont inue driving. See an autho rized
Aud i deale r o r autho rized Audi Serv ice Facili
ty fo r ass is tance.
PARK /(®)/~ Electrom echanical parking
b rake
If the -(U SA mode ls) I. (Canada models)
indicator light turns on, the parking brake was
set.
If the -( U SA mode ls) . (Canada models) in
dicator light blinks, the braking force is not build
ing up enough o r not building up at a ll. Secu re
the vehicle also by selecting the 1st gear (man ual
transm ission) or select ing the P selector lever po
s ition (automatic transm ission) . Make sure the
indicator light is off before you start driving.
l~j Parking brake : malf unction! Please contact
Ser vic e
There is a ma lfunction in the parking brake. Drive
to an autho rized Audi dealer or authorized Audi
Service Facility immed iate ly to have the malfunc
t ion corrected.
11 ( USA model s)/ ,1~a (Can ada models) Parking
brake: caution! Vehicle parked too steep
29
Page 32 of 403
Cockpit over view
There is not enough braking force to hold the ve
hicle in place . The brakes have overheated. The
veh icle cou ld ro ll away even on a small incline .
Ill (U SA mod els)/ lC@j (C an ad a model s) Parking
brake : applied
If th is message appears, press the brake pedal
fi rst a nd the n release the pa rk ing bra ke if neces
sary.
II ( U SA model s)/ l(@j (Canada mo dels) Parking
brak e: emerg ency braking
The emergency braking function was triggered .
Please rele ase park ing b rake
Release the par king brake if t his message ap
pears.
Plea se pr ess brak e pedal to rel ease parking
brak e
To release the park ing brake, press the brake
pedal and press
the ~ button at the same time,
or start driv ing with hill start ass ist
9 page 89,
Starting to drive.
(D Tips
For add it ional information on the park ing
brake, see
9 page 88.
-L Cooling system
• Turn off engin e and che ck co ola nt level. See
o w ner 's manual
The coolant leve l is too low.
Do not cont inue driving and switch the engine
off . Check the coolant level
9 page 329.
- If the coolant level is too low, add coolant
9 page 329. On ly cont inue driving once the in
dicator light turns off .
• Coolant t emper atu re: too high. Let e ngi ne
run with vehicle st ationar y
Let the eng ine run at id le for a few minutes to
coo l off, until the indicator light turns off .
- If the indicato r ligh t does not turn off, do not
contin ue driving the vehicle. See an au thorized
30
Audi dea ler or authorized Audi Service Facility
for assistance.
A WARNING
- Never open the hood if you can see or hear
steam or coolant escaping from the engine
compartment. This increases the risk of burns. Wait until you no longer see or hear
steam or coolant escaping .
- The engine compartment in any vehicle can
be a dange rous area . Stop the engine and
allow it to cool befo re working in the engine
compa rtment. Always follow the informa
tion fo und in
9 page 323, Working in the
engine compartment .
(D Note
Do not continue driv ing if the . indicator
li ght turns on as this increases the risk of en
gine damage.
~ Safety belt
The . indicator light stays on until the dr iver's
and front passenger's safety belts are fastened.
Above a certain speed, there will a lso be a warn
i ng tone.
(D Tips
For additional informat ion on safety belts,
see
Q page 263.
0 Generator/Vehicle battery
If the . or(•) indicator light turns on, there is a
malfunction in the generator or the vehicle e lec
trical system .
• Electrical sy stem: malfunction! Saf ely stop
v ehicle
Do not continue dr iving and switch the engine
off. See an authorized Audi dealer or autho rized
Audi Service Facility for assistance.
(•j Ele ctri cal system: m alfunc tion! Re sta rt not
po ssible. Plea se cont act Ser vice
The vehicle battery was disconnected from the
vehicle e lectr ica l system and will no longer
Page 34 of 403
Cockpit over view
Drive to an autho rized Audi dea ler or a uthorized
Audi Service Facility immediately to have the
malfunct ion corrected.
c::=:,Hood
• Warning! Hood is not locked. Stop vehicle
and check the lo ck
If the indicator light turns on and the m essage
appears, the hood locking mechanism is not en
gaged correctly.
Stop immediate ly and close the hood
<::> page 324.
0 Clutch
Appl ies to: ve hicles w ith manu al transmiss ion
• C lutch: malfun ction! Safely stop vehicle
There is an ongoing ma lfunction in t he clutch .
Stop the vehicle safely. See an authorized Audi
dea ler or a uthori zed Audi Serv ice Facility for as
sistance .
[Pl Clut <:h: malf un<:ti on! Adapt dri ving style .
Please contact Ser vice
There is an ongo ing malfu nction in the clutc h.
The engine torque tha t can be transferred is re
duced . You may continue d riving . Avoid using the
clutch in any way that will p lace a heavy load on
it . For example, do not let the clutch r ub when
starting on hills, when towing a trailer or when
maneuvering the vehicle. Drive to an authori zed
Aud i dealer or authorized Aud i Serv ice Facility im
mediately to have the malfunc tion corrected .
5] Clutch: malfun ction! You ma y continue d riv
ing
There is a malfunction in the clutch. The engine
torque that can be transferred is reduced. Yo u
may continue driving. Avoid using the clutch in
the future in any way that will p lace a heavy load
on it. For examp le, do not let the clutch rub when
starting on hills, when tow ing a trailer or when
maneuvering the vehicle . The indicato r light
tur ns off once the clutc h is fully operable again.
32
!;.J [/; Electronic Stabilization Control (ESC)
If the bJ indicator light blinks while driving , the
E SC o r ASR (A nti-Sl ip Regulation) is act ively regu
l ating .
If the
bJ ind icator light turns on, the system has
switched the ESC off. In t his case, you can switch
t h e ign it io n off and then on to swi tch the ESC on
again. The indicator light t urns off when the sys
tem is functioning fu lly.
If
the . indicator light turns on, ESC was
swi tched off using the
l.a00I button<::> page 146.
Stabi liz ation contro l (ESC /ABS ): malfunction !
See owner's manual
If the G1 ind icator light and the ~ (USA mod
els),11J (Canada models) ABS indicator light turn
o n and the message appears, there is a malfunc
tion in the ABS o r the e lectronic diffe rentia l lock .
This also causes the ESC to malfunction. The
br akes st ill func tion wi th the ir normal power, bu t
ABS is not active .
D rive to an authorized A udi dealer or authorized
Audi Se rvice Fa cil ity immed iate ly to have the
malfunction cor rec ted .
(D Tips
For addi tional informat ion on ESC and ABS,
see <::>
page 146 .
!I..' Safety systems
The fll indicator lig ht mon itors the safe ty sys
tems.
If the
fll ind icator light turns on or blinks, the re
i s a ma lfunction in a safety system.
Drive to an author ized Audi dealer or authorized
Audi Se rvice Fac ility immed iate ly to have the
malfunction cor rected .
_&, WARNING
Have the safety sys tems inspec ted immedi
a tely . O therwise, the re is a ris k t hat the sys
tems may not activate during a collision,
which increases the risk of serious injury or
death .
Page 35 of 403
a co .... N ,....
N .... 0 0
3 co
C© ) Brake system
rm Brakes overheating . Please shift to D
rm Brakes overheating. Please select a gear and
follow gear recommendation
There was a heavy load on the brakes. Engage a
suitable gear (manual transm ission) or place the
selector lever in the D/S position (automat ic
transmission) to use the eng ine braking effect
and reduce the load on the brakes.
~·
:t:J /(0 : Brake pads
II (USA models)/£i1 (Canada models) Brake
pads: wear limit reached. You can continue driv
ing. Please contact Service
The brake pads are worn.
Drive to an authorized Aud i dealer or authorized
Aud i Service Facility as soon as possible to have
the malfunct ion corrected .
c:l:::, Engine control
II Drive system: malfunction! Please contact
Service
There is an engine control malfunction .
Drive slow ly to an author iz ed Audi dealer or au
thor ized Audi Service Facility to have the eng ine
checked .
W Engine control (diesel engine )
Applies to: vehicles with diesel engines
The engine is preheating if the II indicato r light
turns on when the ignition is switched o n.
I f the indicator light does not turn on or b links
while driving , there is an eng ine control malfunc
tion .
Immediately drive slowly to an authori zed Aud i
dealer or authorized Aud i Serv ice Facility to have
the malfunction co rrected .
o Malfunction indicator lamp (MIL)
The malfunction indicato r lamp (MIL) is part of
the On -Board Diagnostic System (OBD II). The Cockpit overview
('4 ,;ymbol turns on when the
ignition is switched
on and turns off again once the engine is started
and running at a steady idle speed. This indicates
that the MIL is function ing correctly.
T he indicator light turns on if there is a malfunc
tion in the engine electronics. See an authorized
Audi dealer or authorized Audi Service Fac ility to
have the malfunction corrected . For additional
information, see
c:::> page 24.
The indicator light can a lso turn on if the fuel fill
er cap is not closed correctly
c:::> page 317.
,m,,
Diesel particulate filter
Applies to : vehicles wit h diesel eng ine a nd diesel particulate
filter
II Particulate filter : malfunction! See owner's
manual
T he diese l particulate filter requires regenera
tion . To support the filter 's self-cleaning func
tion:
Drive for approximately 15 minutes at a mini
mum of 37 mph (60 km/h) in 4th or 5th gear
(manua l transmission) or in the S selector lever
position (automatic transmission). Keep the en
gine speed at approximately 2,000 RPM . The
temperature increase that will result from th is
can burn off the soot in the filter . The ind icator
light will turn off when the cleaning has complet
ed successfully .
If the indicator light does not turn off, drive im
med iate ly to an authori zed Audi dealer or author
ized Audi Service Facility to have the malfunct ion
corrected .
A WARNING "---
Always adapt your speed to the current
weather, road and traffic conditions. You
should never disobey traffic laws in order to
follow driving recommendations .
@ Tips
For additional informat ion on the diesel par
ticulate filter, see
c:::> page 322 .
33
Page 36 of 403
Cockpit overview
!?i Engine speed limitation
(ill Maximum engine speed: XXXX rpm
The engine speed is automatically limited to the
speed displayed in the instrument cluster. This
protects the engine from overheating.
The engine speed limitation deactivates once the
engine is no longer in the critical temperature
range and you have released the accelerator ped
al once.
If the engine speed limitation was activated by
an engine control malfunction, the
II indicator
light also turns on. Make sure the engine speed
does not go above the speed displayed, for exam
ple when downshifting. Drive to an authorized
Audi dealer or authorized Audi Service Facility im
mediately to have the malfunction corrected.
~ ;,,. Engine oil sensor
• Oil level system: malfunction! Please con
tact Service
The sensor to check the engine oil level has
failed. Drive to an authorized Audi dealer or au
thorized Audi Service Facility immediately to have
the malfunction corrected.
• Oil level sensor: oil change necessary. Please
contact Service
Fuel has entered the engine oil as a result of fre
quent short drives. Avoid high engine speeds, full
acceleration and heavy engine loads. Drive to an
authorized Audi dealer or authorized Audi Service
Facility immediately to have the oil changed .
• Oil pressure sensor: malfunction! Please
contact Service
There is a malfunction in the oil pressure sensor.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
f Engine warm-up request
0 Please warm up engine
Fuel has entered the engine oil, either from low
outside temperatures or frequent short drives.
34
Drive until the engine is warm so that the fuel in
the engine oil will evaporate. Avoid high engine speeds, full accelerating and heavy engine loads
when doing this.
Eli) Tank system
ID Please refuel
If the indicator light turns on for the first time
and the message appears, there are about 2.1
gallons (8 liters) of fuel left in the tank.
(jg Please refuel immediately
If the indicator light turns on the message ap
pears, the fuel tank is almost empty. Refuel the
vehicle immediately.
ID Tank system: malfunction! Please contact
Service
Th ere is a malfunction in the fuel tank system.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
{!) Tips
For more information on fueling, see
¢page 317 .
,_ Washer fluid level
m Please add washer fluid
Fill the washer fluid for the windshield washer
system and the headlight washer system* when
the ignition is switched
off¢ page 332.
· 1 Windshield wipers
II Windshield wipers: malfunction! Please con
tact Service
There is a malfunction with the windshield wip
ers.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the malfunction corrected.
Page 37 of 403
a co .... N ,....
N .... 0 0
3 co
c::S Driver's door
II] Driver' s door: malfunction! Shift to P before
l e aving vehi cle. See own er's manual
There is a malfunction in the driver's door. Select
the P se lector lever position (automat ic transmis
sion) to secure the vehicle.
Drive to an authori zed Aud i dealer or authorized
Aud i Service Facility immediately to have the
malfunct ion corrected .
-:
If the II indica to r li ght turns on, a b ulb has
fa iled. The message ind icates the location of the
bu lb . Rep lace the b ulb immediately .
Vehicle lights: malfunction! Please c ont ac t
Servic e
There is a malfunction in the headlights or the
light switch . Drive to an authorized Audi dealer o r
author ized Audi Se rvice Facility immed iate ly to
h ave the ma lf u nction co rre cted.
_& WARNING
- Ligh t bul bs are under pressu re and can ex
plode when bulbs are replaced, which in
creases the risk of injury.
- Wi th H ID headlights (xenon headlights), the
high -voltage component must be handled
correctly. Otherwise, there is a risk of fata l
injury.
{(D Dynamic headlight range control
II He adlight range cont rol: malfun ctio n! S ee
o w ner 's manual
There is a malfunction in the headlight range
control system, which may ca use glar e for other
drivers.
Drive to an authorized Audi dea ler o r a uthorized
Audi Servic e Facility immediately to have the
malfunct ion corr ected.
-
Coc kpit o ve rv iew
~O Audi adaptive light
Applies to: vehicles with Audi adaptive light
m;J Audi adapt ive light : malfun ction! See own
er's manual
Adaptive light is not working . The headlights still
funct ion .
Drive to an au thorized Audi dealer or authorized
Audi Service Facility immed iately to have the
malfunction corrected .
@ Light/rain sensor
!;I Automatic headlights: ma lfunction! See
o wner' s manual
!;I Automati c wipers : malfunction ! See owner' s
manual
The light/rain sensor is malfunctioning.
The low beams remain switched on at a ll times
for safety reasons when the light switch is in the
AUTO position. However, you can continue to
turn the lights on and off using the light switch.
You can still contro l all functions that a re inde
pendent of the rain sensor through the wind
shield wiper leve r.
Drive to an au thori zed Audi dealer or authori zed
Audi Service Facility immed iately to have the
malfunction corrected.
Q Suspension control
Applies to : vehicles with suspension control
II Su sp ension: malfunction! You may continue
drivin g
There is a suspension control malfunction .
Drive to an authorized Audi d eal er or authorized
Audi Service Facility immed iate ly to have the
malfunction correc ted.
r : All wheel drive/sport differential
Applies to: vehicles with all wheel drive/sport diffe rentia l
(II All-wh eel dri ve : malfun ction! You may con-
tinue driv ing. Pl ease contact Service
.,.
35
Page 38 of 403
Cockpit over view
Ill Sport d ifferential : malfunction! Please con
tact Se rvice
There is a malfunction.
Dr ive to an authorized Aud i dealer or authorized
Aud i Serv ice Facility immediately to have the
malfunct io n corrected.
Ill All-whee l dri ve o verhe ating . Ple ase a dapt
driving st yle . See owner' s manual
Ill Sport d ifferential : temper ature too high.
Ple ase adapt drivi ng sty le
The transmission temperature has increased sig
nificant ly due to the sporty driv ing manner. Drive
in a less sporty manner until the temperature re
turns to the normal range and the indicator light
sw itches of .
A WARNING
Contact an authorized Audi dealer or author
ized Aud i Serv ice Facility if the all whee l dr ive/
sport diffe rential is fau lty o r malfunctioning.
The repair must be performed by trained per
sonnel using the correct oil in order to ensure
safety.
¢¢ Turn signals
If the . or .l indicator light b links, a turn s ig
na l is turned on. If bot h indicator lig hts are blink
ing, the emergency flashers are on.
If an indicato r light blinks twice as fast as usua l,
a t urn signa l bulb has failed. Caref ully dr ive to an
authorized Audi dealer or author ized Audi Service
Facility immediately to have the malfunction cor
rected.
36
Page 50 of 403
Opening and closing
Child safety lock
The child safety lock prevents the rear doors
from being opened from the inside and the rear
power windows from be operated .
Fig. 40 Section of driver's door: co ntrols
Fig. 41 Rear door: chil d safety lock
0 N M 9 ::J co (D
• T o deactivate/activate the power window
switch in the rear doors, press the@ button in
the driver 's
door ¢ fig. 40. The indicator light in
the button turns on/blinks.
• To also deactivate/activate the inner door han
dle, open the respective rear door and turn the
key switch with the mechan ical key in the direc
tion of the arrow or opposite the direct ion of
the arrow
<=> fig. 41 .
Message in the instrument cluster display
faj Childproof catch: malfunction! Please con
tact Service
There is a malfunction in the child safety lock.
Press the@ button again.
If the message stays on, drive immediately to an
authori zed Audi dealer or authorized Audi Service
Facility to have the malfunction repaired.
48
A WARNING
-Always take the vehicle key with you when
leav ing the vehicle, even for a short period
of time . This applies part icularly when chil
dren remain in the vehicle . Otherwise chil
dren could start the engine or ope rate elec
trical equipment (such as power windows),
which increases the risk of an acc ident.
- A malfunction in the child safety lock could
allow the rear doors to be opened from the
inside, which increases the risk of an acci
dent .
Power windows
Controls '
The driver con control all power windows .
Fig. 42 Driver"s door: power w indow controls
All powe r window switches are equipped with a
two-stage function :
Opening and closing the windows
a, .... M 0 ::, (X) (D
• To open or close the window completely, press
the switch down or pull the switch up briefly to
the second level. The operat ion will stop if the
sw itch is p ressed/pulled again.
• To select a position in between opened and
closed, p ress/pu ll the switch to the first level
until the desired window position is reached.
Power window switches
CD Left front door
@ Right front door
® Left rear door
© Right rear door