wheel bolts AUDI S6 2013 Owners Manual

214 Cleaning and protec tio n
To preserve the deco rative appearance of the
cast a lloy whee ls , some specia l care is neces­
sary. In addit ion to road dirt and sa lt, brake
dust is also corros ive. If left on for too long,
brake dust can cause pitt ing.
Use only specia l
acid-free cleaners formulated
for a lloy rims. Safe products are available at
your Aud i dealer. Never leave the cleaner on
the r ims longer than spec ified on the label. If
not rinsed off promptly, the acid conta ined in
some cleaners can attack the threads on the
wheel bolts.
Never use abras ive or metal polishing clean­
ing agents . If the protective coating has been
ch ipped, e .g . by k icked up road dirt, touch it
up as soon as poss ible.
A WARNING
- Moisture and ice on brakes may affect
braking efficiency
Q page 194, General
information .
Test the brakes caref ully
each time you wash the vehicle.
- Always read and heed all WARNINGS and
other information ¢
page 208.
-
Body cavity sealing
The body cavity sealing does not need to be
checked.
A ll body cavities wh ich could be affected by
corrosion have been thoroughly protected at
the facto ry.
This sealing does not require any inspection or
addit ional treatment . If any wax should seep
out of the cav ity when the ambient tempera­
ture is high, it can be removed w it h a plastic
scrape r and a suitab le solven t.
A WARNING
So lvents can be dange rous.
- Benzine is flammable and toxic.
If you
use benzine for removing the wax, keep
sparks, flame and lighted cigarettes
away. Never dump benzine on t he
ground, into open streams or down sew­
age drains. -
Be s ure to observe all safety and environ ­
mental regulat ions. Follow all instruc ­
tions on the container .
- Always read and heed all WARNINGS and
other information
Q page 208.
Chassis
Hove the undercoating checked for damage
from time to time .
The lower body shell of your Aud i is also thor­
oughly protected against corrosion .
Any damage to the undercoat ing ca used by
road hazards should be repaired prom ptly.
A WARNING
r----
Too much undercoating in the wrong p la-
ces can cause a fire.
- Do not app ly additional under coating or
r u stp roof ing on or nea r the exhaust
manifold, exhaust pipes, catalytic con­
verter or heat shields . While driving, the
substance used fo r undercoating could
overheat and cause a fire.
-
- Always read and heed a ll WARNINGS and
other information
Q page 208.
Exhaust tail pipes
Road salt and other corrosive materials will
damage the material in the exhaust tail pipes
if they are not cleaned regular ly. Do not clean
the tail pipes with wheel cleaner, pa int polish,
chr ome polish or other ab rasive clea ners.
Clean the tail pipes with ca r c are products
t h at are suitable fo r stainless steel.
Your authorized Aud i dea ler can provide clean­
ing produc ts tha t have been tested and ap­
proved for yo ur vehicle .
Care of interior
Infotainment components
The MMI/RSE* display may be cleaned wit h a
soft clot h and commercia lly-available "LCD
cleaner ". The clot h should be coated lightly ..,

V up to 149 mph (240 km/h)1
)
Z over 149 mph (240 km/h)1)
W up to 168 mph (270 km/h)1l
Y up to 186 mph (298 km/h)
1 )
Your veh icle is norma lly factory equipped with
t ires, which posses s excellen t driving charac­
ter istics and give your Audi opt imum driving
comfort . An electronic speed limiter
~ page 30 w ill normally prevent your vehicle
from go ing faste r th an the tire speed rating
~ &. -
U.S. DOT T ire Identification Number (TIN )
and tire manufactur e date
This is the t ire's "serial numbe r" . It begins
with the le tters "DOT" and indicates that the
tire meets all federal standards . The next two
numbers or letters indicate the p lant where it
was manufactured, and the last four numbers represent the week and year of manufactu re.
Fo r example, the numbers 2212 mean the tire
was produced in the 22nd week of 2012. The
other numbers are market ing codes that may
or may not be used by the t ire manufacturer.
This informat ion is used to contact consumers
if a t ire defect requires a reca ll.
Audi Original tire
Tires with the iden tifica tion "AO" or "RO" have
been spec ially matched with your Aud i. We
recommend using only these tires because
they meet the highest standards regard ing
safety and d riving charac ter istics when used
correctly . Yo ur au thori zed Audi dealer w ill
g lad ly provide you with more information.
Tire ply composition and materials used
The numbe r of p lies ind icates the n umber of
l ayers of rubber-coated fabric i n the t ire. In
gener al, the grea ter the numbe r of p lies, the
more weig ht a tire can s upport. Tire man ufac­
turers a lso must indicate the materials in the
tire, wh ich include ste el, nylon, polyest er, and
others.
ll Fo r tires wit h a m ax im um s pee d ca pabil ity over
1 4 9 m ph (24 0 k m/h) , tire m an ufa ctur ers somet ime s
use the let ters "ZR."
Tire s an d wheel s 253
Maximum Load Rating
This number indicates the max imum load in
k ilograms and po unds t hat can be ca rr ied by
the tire.
Tire quality grading for treadwear ,
traction, and temp eratu re resistance
T read wear, t raction and tempe ra tu re grades
¢ page
254 .
Maximum Permissible Inflation Pressure
This number is the greatest amount of a ir
pressure that should ever be put in the tire
u nder norma l dr iv ing cond itions .
_& WARNING ~
- Using incorrect o r unmatched tires and I
or wheels or improper tire and wheel
comb inat ions can lead to loss of control,
coll is ion and serious personal in jury.
- Always use t ires , rims and whee l bolts
that meet the specif ications of original
factory- installed tires or other combina­
tions that have been sp ecifically ap­
proved by the vehicle manufacture r.
- Tires age even if they are not being used
and can fai l sudden ly, especially at high
speeds . Tires that are more than 6 yea rs
old can only be used in an emergency
and then w ith special care and at lower
speeds.
- Never mo unt used tires on your veh icle if
you are not sure of the ir "previous histo­
ry ." O ld used tires may have been dam­
aged even though the damage cannot be
seen that can lead to sudden tire fai lure
and loss of vehicle control.
-All four whee ls must be fitted with radial
tires of the same type, size (rolling cir­ cumference) and the same tread pattern .
Driving with different tires reduces vehi­
cle handling and can lead to a loss of
control.
•
•

@ Tips
Where snow chains are mandatory oncer­
tain roads, this normally also applies to
veh icles with all-wheel dr ive.
Wheel bolts
Wheel bolts must always be tightened to the
correct torque .
The design of whee l bolts is matched to the
factory insta lled rims . If different rims are fit­
ted, the correct wheel bolts with the right
length and correctly shaped bolt heads must
be used. This ensures that wheels are f itted
securely and that the brake system functions
correctly .
In certain circumstances, you may not use
wheel bolts from a different vehicle -even if it
is the same model
<=> page 287.
.&_ WARNING
Improperly tightened or maintained wheel
bolts can becom e loose caus ing loss of
cont ro l, a co llision and serious persona l in­
Jury .
- Always keep the wheel bolts and the
threads in the wheel hubs clea n so the
w heel bolts can t urn easily and be prop ­
erly t ightened .
- Never grease or oil the wheel bolts and
the threads in the wheel hubs. They can
become loose while d riving if greased or
oi led, even if tightened to the specif ied
torque.
- Only use whee l bolts that belong to the
rim being installed .
- Never use different whee ls bolts on your
vehicle.
- Always maintain the co rrect tighten ing
torq ue for the wheel bo lts to reduce the
risk of a wheel loss . If the tightening tor­
que of the wheel bolts is too low, they
can loosen and come out when the vehi­
cle is moving. If the tightening torque is
too high, the whee l bolts and threads
Tire s an d wheel s 257
can be damaged and the whee l can be­
come loose.
(D Note
The specified torque for the whee l bolts is
90 ft lb (120 Nm) with a tolerance of± 7,4
ft lb(± 10 Nm) . Torq ue whee l bolts diago­
nally. After changing a whee l, the torq ue
must be checked as soon as possible with a
torque wrench -preferably by an author­
i zed Audi dealer or qualified workshop.
Low aspect ratio tires
You r Aud i is facto ry-equ ipped w it h low aspect
ra tio tires. These tires have been tho ro ughly
tested and been se lec ted spe cifically for you r
model for their superb perfo rmance, road fee l
and handling under a variety of driving condi­
tions. Ask your authorized Audi dealer for
more details .
T he low aspect ratio of these t ires is ind icated
by a numera l of
55 or le ss in the tire's s ize
designation. The numera l represents the ratio
of the t ire's sidewa ll height in relation to its
tread width expressed in percentage. Conven­
tiona l tires have a he ight/w idth rat io of 60 or
more .
The performance of low-aspect -ra tio tire s is
particularly sens it iv e to improper inflation
pressure. It is therefore important that low
aspect ratio t ires are inflated to the specified
pre ssure and that the inflation pressur e is
regularly che cked and maintain ed. Tire pre s­
s ures should be checked at least on ce a
m onth and alwa ys before a long trip
¢ page 246, Checking tire pressure .
What you can do to avoid tire and rim
damage
Low aspect ratio tires can be damage d mo re
easily by impact w ith potholes, curbs, g ull ies
or ridges on t he road, partic ularly if the tire is
u nderinflated.
Ill>-
•
•

262 What do I do now?
Vehicle tool kit
Vehicle tool kit and jack
The vehicle tool kit is located in the luggage
compartment under the cargo floor cover .
Fig. 200 Luggage compartment: cargo floor cover
folded upward/spare t ire
Fig . 201 Trunk lid: Vehicle tool kit
• Lift the cargo floor by the plastic handle
c:>fig. 200.
• Hook the handle into the luggage compart­
ment weather strip.
• Turn the handwheel counter-clockwise
c:> fig. 200 and remove the spare tire to
reach the vehicle tool kit.
• Unhook the cargo floor before closing the
rear lid.
The onboard tool kit includes:
- Hooks to remove the wheel covers*
- Plastic hook to remove wheel bolt covers*
- Wheel bolt wrench
-Alignment p in for changing wheels
- Screwdr iver w ith reve rsible blade
- T owing loop
- Jack
Before storing the jack, make sure it is wound
back down as far as it will go.
A WARNING ,-
Improper use of the vehicle jack can cause
serious personal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts can­
not attain the necessary tighten ing tor­
que if you use the hex head, potentially
causing an accident.
- The factory-supplied jack is intended on­
ly for your vehicle model. Under no c ir­
cumstances should it be used to lift
heavy vehicles or other loads; you risk in­
juring yo urself.
- Never start the engine when the vehicle
is raised, wh ich could cause an accident.
- Support the vehicle securely with appro­
priate stands if work is to be performed
underneath the vehicle; otherwise, there
is a potential risk for injury.
- Never use the jack supplied with your
Audi on another vehicle, particu larly on a
heavier one. The jack is only suitable for
use on the vehicle it came with.
(D Tips
- Some of the onboard items listed above
are provided on certain models only or
are optional extras .
- Before you can raise your vehicle using
the jack, you must activate the jacking
mode
c::> page 266.
Space-saving spare tire (compact spare
tire)
The spare tire/wheel is located in the luggage
compartment under the cargo floor cover . It
is intended for short-term use only.
Taking out the spare tire
.,. Lift the cargo floor by the p lastic handle
c::>fig. 200.
.,. Hook the handle into the luggage compart­
ment weather strip.
.,. Turn the large screw
c:> fig. 200 counte r­
clockw ise.
.,. Take out the spare tire .

264 What do I do now?
&_ WARNING
You or your passengers could be injured
while changing a wheel if yo u do n ot fol­
low t hese safety precautions:
- If you have a flat t ire, move a safe dis­
tance
off the road. Turn off the engine,
turn the emergency flashers on and use other warning dev ices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traff ic.
- T o help p revent the veh icle from mov ing
sudden ly and possibly slipping off the
ja ck, always fully set the parking b rake
and bloc k the whee l diagona lly opposite
the whee l being changed. When one
front whee l is lifted off the gro und, plac­
ing the Automat ic Transmiss ion in P
(Park) will
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the
ground is level and firm. If necessary,
use a sturdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced t ire i n the luggage com­
partment
¢ page 132.
Before chang ing the wheel, yo u m ust acti­
vate the jacking mode, so that the auto­ mat ic cont rols for the Adaptive Air S us­
pens ion* do not make it more difficult to
lift the vehicle with the jack
c> page 266.
Changing a wheel
When you change a wheel, follow these­
quence described below step-by-step and in
exactly that order .
1. Activate the vehicle jack mode*
~page 266.
-
2. Remove the decorative wheel cov er* . For
mo re details see also ¢
page 265, Deco­
rative wheel covers
or c> page 265,
Wheels with wheel bolt caps.
3 . L oosen the wheel bolts¢ page 265.
4. Locate the proper mounting point for the
jack and alig n the jack below that point
¢ page 266 .
5.
Raise the car with the jack¢ page 266.
6. Remove the wheel with the flat tire and
then insta ll
the s pare ¢page 267.
7. Tighten all whee l bolts lightly.
8 . Lower the vehicle with the jack .
9. Use the wheel bolt wrench and firmly
t igh ten al l w heel bo lts¢ page 265.
10. Rep lace the decorat ive wh eel co ver* .
11. Deactivate the vehicle jack mode* in the
MMI:
ICARI f u nction button > (Car )* sys­
tems
control button > Se rvicing & chec ks
> A ir susp .: jac k mode > Off .
The vehicle jack mode * switches off automati­
ca lly at speeds above
6 mph (1 0 km/h) .
&_ WARNING ,.__
Always read and follow all WARNINGS and
i nformat ion¢ &.
in Raising the vehicle on
page 266
and c> page 268.
After changing a wheel
A wheel change is not complete without the doing the following.
.,. Always store the vehicle tool kit, the jack *
and the rep laced tire in the luggage com­
partment
¢ page 132.
.,. Check t he ti re pressu re on the spare whee l
immed iate ly after mounting it .
.,. As soon as possib le, have the
tightening
torques
on all whee l bolts checked with a
t o rque wrenc h. The co rrect tighte ning tor ­
que is 90 ft lb (120 Nm).
.,. Have the flat tire
replaced as soon as possi­
b le.
(D Tips
- If you not ice th at the wheel bo lts a re
co rroded and difficult to turn while
changing a tire, they should be rep laced
before you check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked .
ll-

-After changing a wheel, the tire pressure
in all four tires must be checked/correct­
ed and the tire pressure mon itor ing indi­
cator must be stored in the MMI
qpage260 .
Decorative wheel covers
Applies to vehicles: with decorat ive wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts.
Fig. 202 Changing a wheel: Removing the wheel cover
Removing
.,.. Insert the hook (provided with the veh icle
tool kit) in the hole in the wheel hub cover .
.,.. Pull off the
decorative wheel cover
qfig. 202.
Wheels with wheel bolt caps
Applies to vehicles: with wheel bo lts w it h caps
The caps must be removed first from the
wheel bolts before the bolts can be un­
screwed.
Fig . 203 Changing a whee l: remov ing t he wheel bolt
caps
Removing
.,.. Push the plastic clip (provided w ith the ve­
hicle tool kit) over the wheel bolt cap until
What do I do now? 265
the inner retainers on the clip align with the
edge of the cover .
.,.. Remove the cap w ith the
plastic clip (vehi­
cle tool kit)
q fig. 203.
Refitting
.,.. Place the caps over the wheel bolts and
push them back on .
The caps are to protect and keep the wheel
bolts clean.
loosening and tightening the wheel
bolts
The wheel bolts must be loosened before rais ­
ing the vehicle.
Fig . 204 Cha nging a wheel: l oosen ing th e whee l bo lts
loosening
.,.. Slide the wheel wrench onto the wheel bolt
as far as it w ill go.
.,.. Take tight hold of the
end of the wrench
handle and turn the wheel bolts
counter­
clockwise
about one single turn in the direc­
tion of arrow
q fig . 204.
Tightening
.,.. Slide the wheel wrench onto the wheel bolt
as far as it w ill go .
.,.. Take tight hold of the
end of the wrench
handle and turn each wheel bolt
clockwise
until it is seated.
_&. WARNING
- Do not use force or hurry when chang ing
a wheel -you can cause the vehicle to slip
off the jack and cause serious personal injuries.

266 What do I do n ow ?
-Do not loosen the wheel bolts more than
one turn
before you raise the veh icle with
the jack. -You risk an injury .
@ Tips
-Never use the hexagonal socket in the
handle of the screwdriver to loosen or
tighten the wheel bo lts.
- If a whee l bolt is very tight, you may find
it easier to loosen by carefully pushing
down on the end of the wheel bolt
wrench w ith
one foot only. As you do so,
hold on to the car to keep your balance
and take care not to slip .
Raising the vehicle
The vehicle must be li~ed with the jack first
before the wheel can be removed .
Fig. 20 5 Sill pa nels : m ark ings
~
9
---;~ :~-;;:--~
Fi g. 20 6 Sill: pos ition ing the ve hicle jack
.,. Activate the vehicle jack mode* in the MMI :
I CAR! func tion button > (C ar)* sy ste m s con ­
t ro l butto n
> Servici ng & che ck s> Air su sp. :
j a ck mode > On .
.,. Engage the parking br ake to prevent your
vehicle from ro lling unintentionally.
.,. Move the
sel ector le ve r to po sit ion P .
.,. Find the marking (imprint) on the sill that
is nearest the wheel that wi ll be changed
¢
fig. 205. Be hind the marking, there is a
lift ing point on the sill for the vehicle jack .
.,. Vehicles with a sill: remove the cover from
the sill before lift ing the veh icle w ith a vehi ­
cle jack ¢
page 267.
.,. Turn the vehicl e jack located under the lift­
ing point on the sill to ra ise the jack u nti l its
arm @¢
fig. 206 is located under the des­
ignated p lastic mount ¢_&. ¢(!).
.,. Align the jack so that its arm@¢
fig. 206
engages in the designated lifting point in
the door si ll and the movable base @ lies
flat on the ground. The base ® must be
ver­
t ical
under the lifting point @ .
.,. Wind the jack up fu rther until the f lat t ire
comes off the ground ¢
,&..
Position t he veh icle jack onl y under the desig­
nated lifting points on the s ill ¢
fig . 205.
T here is exactly one locat ion for each wheel.
T he jack must not be positioned at any other
location ¢ _& ¢(j) .
An
un stab le surfa ce under the jack can cause
the vehicle to slip off the jack . Always provide
a firm base for the jack on the ground .
If nec­
essary place a sturdy board or sim ilar support
u nder the jack. On
h ard , s lipp ery surf aces
(such as tiles) use a rubber mat or similar to
preve nt the jack from slipping ¢
.&..
A WARNING
--You or your passengers co uld be injured
while changing a wheel if you do not fo l­
low these safety precautions:
- Position the vehicle jack on ly at the
designated lifting poi nts and align the
jac k. Otherw ise, the vehicle ja ck could
slip and cause an injury if it does not
have sufficient hold on the vehicle.
- A soft or uns table su rface under the
j ack may cause the vehicle to slip off
the jack . Always provide a firm base for
the jack on the ground. If necessary,
use a sturdy board under the jack. ,...

-On hard, slippery surface (such as tiles)
use a rubbe r mat or similar to prevent
the jack from slipping .
- To he lp prevent injury to yourself and
your passengers:
- Do not raise the vehicle until yo u are
sure the jack is secu rely engaged.
- Passengers must not remain in the ve­
h icle when it is jac ked up.
- Make sure that passengers wa it in a
safe p lace away from the vehicle and
well away from the road and t raffic.
- Make sure jack position is correct , ad­
just as necessary and then continue to
r ai se the jack.
- Changes in temperatur e or load can af­
fect the height of the ve hicl e.
(D Note
Do not lift the ve hicle by the s ill. Position
the vehicle jack only at the des ignated
lift­
ing points on the sill. Othe rwis e, your vehi­
cle will be damaged.
(D Tips
The vehicle jack mode* switches off auto­
mat ica lly at speeds above 6 mph (10 km/
h).
Removing and installing the sill cover
Applies to vehicles : wit h sill
Fig. 207 Sill: remov ing t he cover
.,. Pull the cover down to remove it c::> fig . 207.
.,. To install the cover again, inse rt it into the
retainers and then sw ing it upward unt il it
cl icks into place . T he cover m ust be flush
with the sill.
What do I d o now ? 267
@ Tips
Some models may also have a cover for the
rear vehicle lift po int.
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing th e wheel.
Fi g. 208 Cha ngi ng a w heel: us ing th e screwd rive r ha n­
d le (w it h th e blade re m oved) to turn the bo lts
F ig . 209 Chang ing a whee l: a lig nment p in in sid e the
top hole
After you have loosened all wheel bo lts and
raised the vehicle
off the ground, remove and
replace the wheel as follows :
Removing th e wheel
.,. Use the hexagonal socket in the screwd riv ­
er handle
to complete ly remove the top­
most wheel bolt and set it aside on a
clean
surface c::> fig. 208 .
.,. Screw the threaded end of the alignment
pin
from the tool kit hand-t ight into the
empty bolt hol e
c::> fig. 209 .
.,. Then remove the other wheel bolts as de­
scribed above .
.,. Take
off the whee l leaving the alignment
pi n in the bolt hole
c::> (l).

268 What do I do no w?
P uttin g on the spare wheel
.. Lift the spare wheel and ca refully slide it
over the alignment pin to guide it in place
¢ (D .
.. Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bolts
slightly.
.. Remove the alignment pin and insert and
t ighten the remaining wheel bolt slightly
L ike the rest .
.. Turn the jack handle cou nter -clockw ise to
lower the vehicle unt il the jac k is fully re­
leased.
.. Use the wheel bolt wrench to tighten all
wheel bolts firmly¢
page 265 . Tighten
them
crosswise, from one bolt to the (ap­
proximately) opposite one, to keep the
wheel centered.
When removing or installing the wheel,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you .
(j) Tips
Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or t ighten
the wheel bolts .
- Pull the reversible blade from the screw­
driver before you use the hexagonal
socket in the handle to turn the wheel bo lts.
- When mounting tires with
unid irectional
tread design
make sure the tread pat­
tern is pointed the right way
¢ page 268.
-The wheel bolts should be clean and easy
to tu rn . Check for d irt and corrosion on
the mat ing su rfaces of both the whee l
and the h ub. Remove al l dirt from these
surfaces before remo unting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Using a sp are t ire w ith a tre ad pattern
intended for use in a specific direction
When using a spare t ire with a tread patter n
intended for use in a spec ific d irection , please
note the following :
- The direct ion of rotation is marked by an ar­
row on the side of the tire .
- If the spare tire has to be installed in the in­
correct direct ion, use the spare tire only
temporarily s ince the tire will not be able to
achieve its optimum performance cha racter­
isti cs wit h regard to aquap lan ing, no ise and
wear .
- We recommend that you pay part icu la r at­
t ention to th is fact d uring wet wea ther and
t ha t you adjust you r speed to match road
conditions .
- Replace the fl at tir e with a new one and
have it insta lled on you r vehicle as soon as
possible to restore the handling advantages
of a u nidirectional tire .
Notes on wheel changing
Please read the information¢ page 251, New
tires and replacing tires and wheels
if you a re
going to use a spare tire which is different
from the ti res on your vehicle .
After you change a tire:
- Check the tire pre ssure on the spar e imm e­
diately after install ation.
- Have th e whe el bolt tight ening torqu e
c hecked with a torque wrench as soon a s
pos sible by your author ized Audi de aler or
a q ualified service stat ion.
- With steel and allo y wheel r im s, the wheel
bolt s ar e cor re ctl y tightened at a torque of
90 ft lb (1 20 Nm ).
- If you noti ce th at the wheel bolts are cor­
roded and diffi cult to turn while changing
a ti re , they should be repl aced before you
check the t ightening torque. .,..

300 Index
Sunroof .......... ......... ... .... .. 40
Sun shade
Rear window ............. .... .... ..
45
Side doors . . . . . . . . . . . . . . . . . . . . . . . . . 45
Sun visors . .................. ... .. .. 45
Symbo ls
refer to Warning/indicator lights .... .. 12
T
Tachometer . . . . . . . . . . . . . . . . . . . . . 12, 23
Technical modifications .......... .... 288
Temperature disp lay .................. 23
Tether anchors .......... ...... .. .. . 188
Tether strap ................... ... . 188
The first 1,000 miles (1,500 km) and after-
wards ... .... ................ ..... .
199
Three-zone cl imate control ............ 65
Tie-downs . . . . . . . . . . . . . . . . . . . . . 62, 133
Tips for the environment
Saving fuel . . . . . . . . . . . . . . . . . . . . . . . .
60
tiptronic .. ... .............. .. .. .. . 105
tiptronic (automatic transmission) .. ... 109
Tire pressure ............... ... .... . 246
Tire pressure monitor ing system .. .. .. . 258
Loss of air pressure ......... .. .. .. . 259
Malfunct ion ............. ......... 259
Resett ing t ire pressures ............. 260
Tires .......................... ... . 240
Service life .... .... ...... ...... .. . 250
Speed rating letter code ....... .. ... 252
Tire manufacturing date ....... .... . 252
Tire specifications ................. 252
Tread depth ................ ..... . 250
Uniform tire quality grading .. ... ... . 254
Winter tires .............. ... .... . 255
Tires and vehicle load limits ........... 248
Tires and wheels
Check ing tire pressure ...... ... .. .. .
246
Cold tire inflat ion pressure ..... .. ... 244
Dimensions . .................. ... . 251
General notes . . . . . . . . . . . . . . . . . . . . . 240
Glossary of t ire and load ing termino lo-
gy .. .... .. ................ ... ...
241
Low aspect ratio tires ....... ... .... . 257
New tires and wheels .......... .... . 251
Replacing ........................ 252
Snow chains ..... ................ . 256
Tires and vehicle load limits ...... ... 248
Whee l bolts ... .. ................ . 257
Winter tires .................. .... 255
Tire service life ..................... 250
Tools .. ....... ................... . 262
Torn or frayed safety belts ......... ... 139
Touc h-up pa int ..................... 213
Towing
Tow truck procedures ...............
276
TPMS
Tire pressure monitoring system .....
259
Traile r towing .................. .... 204
Operating instructions .............. 204
Parking system ... ................ . 123
Technical requirements . . . . . . . . 204, 205
Trailer towing tips . ............... . 206
Train (transport ing your vehicle) . ...... 278
Transmission
l 't . ® 105 mu t1 ronic ..... ................ .
S tronic ® ..... ................... .
105
tiptronic ...... .. .......... ....... 105
Transmission malfunction (indicator
light) .............................
110
Transport Canada .. ................ . 134
Transporting your vehicle ............ . 278
Tread Wear Indicator (TWI) ........... 250
Trip odometer . .... .................. 27
What does it mean when DEF appears in
the trip odometer display? ....... ... .
27
T runk
refer to Luggage compartment ........ 61
Trunk escape handle ................. 261
Trunk lid
refer to Rear lid .................. .. 37
Turn signals . .. .. .. ..... ........ ..... 43
Warning/ind icator lights ............. 23
u
Undercoating ...................... 214
Unfastening safety belts ........... .. 141
U nidirectional tires ... ........... .... 240
Uniform tire quality grading .......... 254