warning AUDI S7 2012 Owners Manual

252 What do I do n ow ?
What do I do now?
Emergency warning
triangle
App lies to vehicles: with emerge ncy warning triangle
The warning triangle is located on the inside
of the trunk lid .
-
"' M ~ 0 6
~ ~
Fig. 183 Trunk lid: Warning triang le
.,. To open the cover, turn the locking mecha ­
nism and pull the cover downward .
" m
.,. Remove the warning triangle from its hold­
er.
The rear lid is only designed to hold the warn ­
ing triangle offered by the original accessories
program. If you would like to retrofit your ve­
hicle with a warning triangle, p lease contact
your authorized Audi dealer.
Vehicle tool kit
Vehicle tool kit and jack
The vehicle tool kit is located in the luggage
compartment under the cargo floor cover.
Fig . 184 Luggage compartment: cargo floor cover
folded upward/spa re t ire
Fig. 185 Trunk lid: Veh icle tool kit
.,. Fold the floor to the seatback with the help
of the handle .
.,. Tu rn the handwheel counter-clockwise
~ fig. 184 and remove the spare t ire to
reach the vehicle tool kit.
The onboard tool k it includes:
- Hooks to remove the wheel covers*
- Plastic hook to remove wheel bolt covers*
- Wheel bolt wrench
-Alignment pin for changing wheels
- Screwdriver with reversib le b lade
- Towing loop
-Jack
Before storing the jack, make sure it is wound
back down as far as it will go.
A WARNING
Improper use of the vehicle jack can cause
serious pe rsonal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts can­
not attain the necessary tighten ing tor­
que if you use the hex head, potentially
causing an acc ident.
- The factory-supplied jack is intended on­
ly for your vehicle model. Under no c ir­
cumstances sho uld it be used to
lift
heavy veh icles or other loads; you risk in­
juring yo urself.
- Never start the engine when the vehicle
is raised, which could cause an accident.
- Support the vehicle securely with appro­ priate stands if work is to be performed
underneath the vehicle; otherwise, there
is a potentia l risk for injury. .,.

-Never use the jack s upplied with your Au­
di on another vehicle, particularly on a
heavier one. The jack is only suitable for
use on the vehicle it came w ith.
(D Tips
- Some of the on board items listed above
are provided on certain mode ls only or
are optional extras.
- Before you can raise your vehicle using
the jack, you must activate the jack ing
mode
¢ page 256.
Space-saving spare tire (compact spare
tire)
The spare tire/wheel is located in the luggage
compartment under the cargo floor cover . It
is intended for short-term use only.
Taking out the sp are tire
... Fo ld the floor to the seatback with the help
of the handle.
... Turn the large sc rew
¢ page 2 52, fig. 184
counter-clockw ise .
.,. Take out the spare tire .
Securing the replaced tire
.,. The fault wheel will not fit ins ide the spare
wheel well. Store it in the luggage compart­
ment and secure it so that it does not slide
¢ page 59 .
Using the spa re tire (compact spare tire )
The compact spare tire is only intended for
emergencies until you can reach a repair shop.
Replace it as quickly as poss ible with a stand­
ard wheel and t ire .
There are some restrictions on the use of the
compact spare t ire. The compact spare t ire
has been des igned specifically for your type of
vehicle.
It must not be swapped with a com­
pact spare t ire from another type of veh icle .
Snow chain s
For technical reasons, the use of snow chains
on the compact spare tire is
not perm itted .
What do I do now? 253
If you do have to drive with snow chains and a
front tire fails, mount the spare wheel with
tire instead of a rear tire. Install the snow
chains on the rear tire and use it to rep lace
the defect ive front tire.
A WARNING
- Never use the spare t ire if it is damaged
or if it is worn down to the tread wear in­
dicators .
- If the spare tire is more than 6 years old,
use it only in an emergency and with ex­
treme caution and careful driv ing.
- The spare tire is intended only for tem­
porary and short-term use.
It should be
replaced as soon as poss ible wi th the
normal whee l and tire.
- After mounting the compact spare t ire,
the t ire pressure must be checked as
soon as possible. T he tire pressure of the
compact spare tire must be 4 .2 bar; oth­
erwise, you risk having an accident.
- Do not dr ive faste r than 50 mph (80 km/
h). You ris k having an accident.
- Avoid full-thrott le accelera tion, heavy
braking, and fast cornering . You risk hav ­
ing an accident.
- Never drive using more than one spare
wheel and tire . You risk having an acci ­
dent .
- Normal summer or winter t ires must not
be mounted on the compact spare wheel
rim.
- For technical reasons, the use of tire chains on the spare tire is not permitted.
If it is necessary to drive with t ire chains,
the spare wheel must be mounted on the
front axle in the event of a flat in a rear
tire. The newly available front wheel must then be installed in place of the
rea r whee l w ith the flat tire . Installing
the t ire cha in before mounting the whee l
and tire is re commended.
- Loose items in the passenger compart­
men t can cause se rious personal injury
during hard brak ing or in an accident. •
•

254 What do I do now?
-Never st ore the inflatable spare tire or
jack and tools in the passenger com­
partm ent.
- Always s tore a ll jacking equipment,
too ls, and the inflatable spare tire in
the luggage compartment.
- Tighten the knurled retaining screw for
the inflatable spare tire securely.
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel .
" After you experience a tire fa ilure, pull t he
ca r well away from moving traffic and try to
r each
level gro und before you stop c::> ,&. .
" All passengers sho uld leave the car and
move to a safe loca tion (fo r inst ance, behind
the g uardrail)
c::> ,&. .
" Engage the parking brake to prevent your
vehicle from ro lling unintentionally
c::> ,&. .
" Move selecto r lever to pos ition Pc::> ,&. .
" If you are tow ing a trailer, unh itch the tra il­
er from your veh icle .
" Take the
jack and the spare tire out of the
l uggage compartment
c::> page 252 ,
c::> page 253.
.&_ WARNING
You or your p assengers cou ld be injured
while changing a whee l if you do not fol ­
low t hese safety preca utions:
- If you have a fl at t ire, move a safe dis­
tance off the road . Tur n off the engine,
t ur n the emergency flas hers o n and use
other warning dev ices to alert other mo­
torists .
- Make su re that passengers wait in a safe
place away from the vehicle and well
away from the road and traff ic.
- To help p revent the veh icle from mov ing
sudden ly and possibly slipping off the
jack, always fully set the parking brake and block th e whee l diago na lly opposite
-
the wheel be ing changed . When one
front wheel is lifted off the ground, plac­ ing the Automatic Transmission in "P"
(Park) will
not prevent the vehicle from
mov ing .
- Before you change a wheel, be sure t he
ground is level and firm. If necessary, use a sturdy board under the jack .
- After insta lling the spare wheel, make
sure tha t you replace the fla t tire/wheel
i n its storage area prope rly and tighten
the knurled retain ing screw secu rely.
Changing a wheel
When you change a wheel , follow these ­
quence described below step-by-step and in
exactly that order.
1. Remove the decorative wheel cover* . For
more details see also
c::> page 255, Deco­
rative wheel covers
or c::> page 255,
Wheels with wheel bolt caps.
2 . Loosen the wheel bolt s c::>page 255.
3. Loc ate the p roper moun ting poin t for th e
jac k an d align the jack be low that poin t
c::>page 256 .
4. Raise the car with the jack c::> page 256.
5. Remove the wheel with the flat tire and
then insta ll
the spare c::> page 257.
6. Tig hte n all whee l bolts lightly .
7.
Lower the vehicle wi th the jack .
8 . Use the wheel bolt w rench and
firmly
t ig ht en al l w heel bo lts c::> page 25 5.
9. Re place the decora tive wheel cover* .
A WARNING
Always read and fo llow all WA RNINGS and
i nformat io n
c::> & in Raising the vehicle on
page 257
and c::> page 258 .
After changing a wheel
A wheel change is not complete withou t the
doing the following .
" Replace the too ls and the jac k in their prop-
er lo cat io n. .,.

256 What do I do now ?
Loo sening
.,. Slide the wheel wr ench onto the wheel bolt
as far as it will go .
.,. Take tight hold of the
end of the wrench
hand le and turn the wheel bolts
co unter ­
clock wise
about one single turn in the direc ­
t ion of arrow
c:;, fig. 188.
Tighten ing
.,. Slide the wheel wrench onto the whee l bolt
as far as it will go .
.,. Take tight hold of the
end of the wrench
hand le and turn each wheel bolt
clock wise
until it is seated.
_& WARNING
- Do not use force or hurry when changi ng
a whee l - you can cause the vehicle to slip
off the jack and cause ser ious persona l
injuries.
- Do not loosen the wheel bolts more than
one turn
before you raise the veh icle with
the jack. -You r isk an injury.
@ Tips
- Never use the hexagonal socket in the
handle of the screwdrive r to loosen or
tighten the wheel bo lts.
- If a wheel bolt is very tight, you may find
i t easier to loosen by ca refully p ush ing
down on the end of the wheel bolt
wrench w ith
one foot only. As yo u do so,
ho ld on to the car to keep your ba lance
and take care not to slip .
Raising the vehicle
The vehicle must be lifted with the jock first
before the wheel can be removed .
Fig . 1 89 C hang ing a whee l: moun ting po in ts for th e
j ack
Fi g. 1 90 Close -up: prope r posit io ni ng o f jack
.,. Engage the p ar king brak e to prevent your
veh icle from rolling unintentionally .
.,. Move the
select or lever to p osition P .
.,. Posit ion the jack below the door s ill under
the
mounting point that is closest to the
wheel to be changed
c:;, fig . 189.
.,. Extend the ja ck u nder the lifting point on
t he door s ill until its arm is pos it ioned di ­
rectly under the lifting point
c:;, &_ .
.,. Align the jack so that its arm @ c:;, fig. 190
engages in the designated lifting point in
the door s ill and the movable base @ lies
flat on the ground . The base @ must be
ver­
tical
under the lifting point @ .
.,. Wind the jack up further until the flat t ire
comes off the ground
c:;, ,& .
The jack must be installed only at the places
indicated
c:;, fig . 189 . There is exactly one loca ­
t ion for each wheel. The jack must not be
positioned at any other location
c:;, ,&. .
An
unstab le surface under the jack can cause
the vehicle to slip off the jack . Always provide
II>-

a firm base for the jack on the ground. If nec­
essary place a sturdy board or similar support
under the jack. On
hard, slippery surfaces
(such as tiles) use a rubber mat or sim ilar to
prevent the jack from slipping¢ .&.
A WARNING
-You or your passengers could be injured
wh ile chang ing a wheel if you do not fol­
low these safety precautions:
- Positioning the jack under the vehicle
at any other place than those indicated
above may damage the vehicle or may
result in personal injuries.
-A soft or unstab le surface under the
jack may cause the vehicle to slip off the jack. Always provide a firm base for
the jack on the ground. If necessary, use a sturdy board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping.
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Pa ssenge rs must not remain in the
ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct , ad­
just as necessary and then continue to
raise the jack .
- Changes in temperature or load can af­
fect the height of the vehicle .
What do I do now? 257
Taking the wheel off /installing the spare
Follow these instructions step-by-step for
changing the wheel.
F ig . 191 Changing a wheel: u sin g the screwd river han­
dle (with the blade removed) to turn the bolts
Fig. 192 Changing a whee l: alignment pin inside the
top ho le
After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.., Use the hexagonal socket in the screwdriv­
er handle
to completely remove the top·
most wheel bolt and set it aside on a
clean
surface ¢fig. 191.
.., Screw the threaded end of the alignment
pin
from the tool kit hand-t ight into the
empty bolt hole
¢fig. 192 .
.., Then remove the other wheel bolts as de­
scribed above .
.., Take off the wheel leaving the alignment
pin in the bolt hole ¢(D.
Putting on the spare wheel
.., Lift the spare wheel and carefully slide it
over the alignment pin to guide it in place
¢(D.

-Replace the flat tire with a new one and
have it installed on your vehicle a s soon as
possible. Remount the wheel co ve r.
U ntil th en, driv e with extr a car e and at re ­
du ced speeds .
~ WARNING
-
-If you are going to equip your vehicle
with t ires or rims wh ich differ from those
wh ich were factory installed, then be
sure to read the informat ion
c:> page 242,
New tires and replacing tires and
wheels.
- Always make sure the damaged wheel or
even a flat tire and the jack and tool k it
are properly secured in th e luggage com·
partment and are not loose in the pas·
senger compartment.
- In an accident o r sudden maneuver they
c ou ld fly forward, inju ring anyone in the
vehicle .
- Always store damaged w heel, jac k and
tools secure ly in the luggage compart­
ment. Otherw ise, in an acc iden t or sud­
den maneuver they cou ld fly forward,
causing injury to passenge rs i n the vehi·
cle .
What do I do now? 259
•
•

260 Fuses and bulbs
Fuses and bulbs
Fuses
Replacing fuses
Fuses that have blown will have metal strips
that have burned through.
Fig. 193 Driver side of the cockpit: fuse panel cover
The fuses are located at the front left and
right of the cockpit and behind the trim on
the right side of the luggage compartment.
• Switch the ignition and the affected electri­
cal equ ipment off.
• Check the following table to see which fuse
belongs to the consumer.
• Remove the cover¢
fig. 193 or¢ page 214,
Opening the side trim.
• To remove the purple plastic cl ip if necessa­
ry
ll, hold onto it at the small side and pull
it out of the fuse panel
c:> page 260,
fig. 194 .
• Remove the clamp from the rear side of the
fuse cover <>
fig. 193 .
• Remove the fuse using the clamp and re­
place the blown fuse w ith an ident ical new
one.
A WARNING
Do not repair fuses and never replace a
blown fuse with one that has a higher amp
rating. This can cause damage to the elec­
trical system and a fire.
ll You ca n dispose of the plastic clip after remov ing it.
(D Note
If a new fuse burns out again after shortly
have you have installed it, have the electri­
cal system checked by your authorized Au­
di dealer .
(D Tips
-The following table does not list fuse lo­
cations that are not used.
- Some of the equipment items listed are
optional or only available on certain
model configurations.
Driver side cockpit fuse assignment
Fig. 194 Drive r side cockpit: fuse panel with plastic
bracket
Fuse panel @ (black)
No. Equipment Amps
1
Switch panel, seat heating,
5 starting assist, control module
2
Automatic dimming interior
s rearview mirror
4
Suspension control system sen-
5 sor
ESP control module
5

Fuse panel @ (green )
Equipment Amps
Parking system 5
Rear Seat Entertainment s
8 Audi side ass ist 5
9
Gateway, Vehicle electrical sys-
5 tern control module 1
10 Sport d ifferential 5
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace burned
out bulbs for you .
It is becoming increasingly more and more
difficult to replace vehicle light bulbs since in
many cases, other parts of the car must first
be removed before you are able to get to the
bu lb. Th is applies especia lly to the light bu lbs
i n the front of your car which you can only
reach through the engine compartment ,
Sheet metal and bulb holders can have sharp
edges that can cause ser ious cuts, and parts
must be correctly taken apart and then prop­
e rly p ut back together to help prevent break­
age of parts and long term damage from wa­
ter that can enter housings that have not been properly resealed.
F or your safety, we recommend that you have
your authorized Audi dealer replace any bu lbs
for you, since your dealer has the proper tools, the correct b ulbs and the expertise.
Gas disc harge la mp s (X enon li ght s):
Due to the high electrical voltage, have the
bu lbs rep laced by a qualified technician.
H eadlights with Xenon l ight can be identified
by the high voltage stic ke r.
LED headlights* requ ire no ma intenance .
Please contact your autho rized Aud i deale r if a
bu lb needs to be replaced.
Fu ses and bulb s
A WARNING
Contact with h igh-vo ltage components of
the electrical system and improper re­
placement of gas discharge (Xenon) head­
light bulbs can cause ser ious personal in­
jury and death.
- Xenon bulbs are pressur ized and can ex­
plode when being changed.
- Changing Xenon lamps requ ires the spe­
cial tra ining, instructions and equip­
ment.
- On ly an authorized Audi dealer or other
qualified wor kshop should change the
bu lbs in gas discharge lamps .
A WARNING
There are parts with sharp edges on the
openings and on the bulb holders tha t can
cause serious c uts.
- If you are uncertain abo ut what to do,
have the work performed by an author­
ized Audi dealer or other qualified work­
shop . Ser ious personal inj ury may result
from improperly performed work.
(D Tips
- If you must replace the light bulbs your­
sel f, a lways remember that the engine
compartment of any vehicle is a hazard­
ous area to work in. A lways read and
heed all WARNINGS
¢ page 210, Engine
compartment¢ ,&..
- It is best to ask your authorized Audi
dealer whenever yo u need to change a
bulb.
-
263
•
•

264 Emergency situations
Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who
have the necessary tools and equipment to
perform these ope rations.
Starting by pushing or
towing
Q;) Note
Vehicles w ith an automatic transmission
cannot be started by pus hing o r tow ing.
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine should fail to start because of a
discharged or weak battery, the battery can be
connected to the battery of
another veh icle,
using a
pair of jumpe r cables to start the en­
g ine .
Jumper cables
Use only jumper cables of sufficiently large
cross section to carry the starter current safe­
ly. Refer to the manufacturer's specif ications.
Use only jumper cables with
insulated termi­
na l clamps which are distinctly marked:
plus(+) cable in most cases colored red
minu s(-) cable
in most cases colored black .
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal
inju ry. Follow the instructions below for
safe handling of your veh icle's battery.
- Always shield you r eyes and avoid lean­
ing over the battery whenever possible.
- A discharged battery can freeze at tem­
peratures just be low 32 °F (0 °C). Before connecting a
jumper cable, you must
thaw the frozen battery complete ly, oth­
erwise it could explode.
- Do not allow battery acid to contact eyes
or skin. Flush any contacted area with
water immediately.
- Improper use of a booster battery to start a vehicle may cause an explosion.
- Vehicle batteries generate explosive gas­
es. Keep sparks, flame and lighted ciga­
rettes away from batteries.
- Do not try to jump start any vehicle with a low acid level in the battery.
- The vo ltage of the booster battery must
also have a 12-Volt rating. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged bat­
tery . Use of batteries of d ifferent voltage
or substantially different "Ah" rating
may cause an exp losion and personal in­
jury.
- Never charge a frozen batte ry. Gas trap­
ped in the ice may cause an explosion.
- Never charge or use a battery that has
been frozen. The battery case may have
be weakened.
- Use of batter ies of different voltage or
substantially different capacity (Ah) rat­
ing may cause an exp losion and injury.
The capacity (Ah) of the booster battery
should not be lower than that of the dis ­
charged battery.
- Before you check anything in the engine
compartment, always read and heed a ll
WARNINGS
¢page 210, Engine com­
partment.
«I) Note
-Applying a higher voltage booster bat­
tery will cause expensive damage to sen­
sitive electronic components, such as
contro l units, relays, rad io, etc.
- There must be no electrical contact be­
tween the vehicles as otherwise current
could already start to flow as soon as the
positive(+) terminals are connected. ..,_

@ Tips
The disc harged battery must be properly
connected to the vehicle's electrical sys­
tem. When jump starting or charg ing the
battery, never connect the negative
ground cable to the batte ry negat ive post
because the ba tte ry manager system must
be ab le to detect the battery's state of
charge. Always connect the negative
g round cab le to the negative ground pos t
of t he battery manager cont ro l unit.
Use of jumper cables
Make sure to connect the jumper coble
clomps in exactly the order described b elow!
Fi g. 197 Eng ine co mpar tment: connecto rs for jum p
s tar t cab les and ch arg er
F ig. 1 98 Jump start in g w ith t he ba ttery of a not her ve ·
hi cle :
@-booster battery, ®-di sc harged ve hicle bat ­
te ry
The procedure des cribed below fo r connecti ng
jumper cables is intended to provide a jump
start for your veh icle.
Vehicle with discharged battery :
• Turn off ligh ts and accessories, move leve r
of automatic t ransmission to
N (Ne utral) or
P (Park) and set par king b rake.
Emergenc y situ ation s 265
Connect POSI TIVE(+) to POSITIVE(+ )
(red )
• Open the red cover on the positive terminal
¢fig. 19 7.
1. Connect one end of the red positive cable
on the jump sta rt bolt
¢ fig. 198 (D (bolt
under the red cover = "positive") of the ve ­
hicle to be started @.
2 . Connect th e othe r end to the pos itive ter-
mi na l@ of the booster battery @.
Connect NEGATIVE( -) to NEGATIVE(-)
(black )
3. Connect one end of the black negative ca­ ble to the negat ive termi na l@ of the
booster b attery @.
4. Connect the othe r end to the jump start
pin @ (bo lts w ith hex head bolt = "nega ­
tive") of the vehicle to be started @.
Starting the engine • Sta rt the engine of the veh icle w ith the
booste r ba tte ry @ . Ru n the engi ne at a
modera te speed.
• Start engine wit h discha rged vehicle battery
@ in the usual manner.
• If the eng ine fails to sta rt, do not keep the
starter c ranking for longer than 10 seconds.
Wait for about 30 seco nds a nd the n try
aga in .
• With eng ine runni ng , remove j umper cab les
from both vehicles in the exact
reverse o r­
de r.
• Close the red cover on the posi tive term inal.
T he battery is v ented to th e outside to p rev ent
gases from en ter ing the veh icle in ter io r. Ma ke
s ur e th at the jumper clamps are well connec t­
ed with their meta l parts in full con ta ct w ith
the battery term inals.
,8. WARNING
To avoid se rious personal injury and dam­
age to the veh icle, heed all warnings and
instructions of the jumper cable man ufac ­
ture r. If in doubt, call for road service .
- Ju mpe r cables m ust be long enough so
that the veh icles d o not touch.
-