wheel AUDI S7 2013 Owners Manual

2 70 What do I do now ?
After changing a wheel
A wheel change is not complete without the
doing the following .
.. Always store the vehicle too l kit, the jack*
and the replaced ti re i n the luggage com­
partment ¢
page 136.
.. Check the tire pres sure on the spare w heel
i m media tely after mount ing it .
.,. As soo n as po ssible, have the
tightening
torques
on a ll w heel bol ts checked with a
tor que wrench . The correct tightening tor ­
que is 90 ft lb ( 120 Nm) .
.. Have the flat tire
replaced as soon as poss i­
ble.
@ Tips
- If you notice t hat the whee l bolts are
corroded and difficult to t urn while
changing a t ire, they should be replaced
bef ore yo u check the tighten ing torque .
- Drive at reduced speed unt il y ou have the
tightening torques checked .
- After changing a wheel, the tire pressure
i n a ll four tires must be checked/cor rect­
ed and t he tire pressure mo nitor ing indi­
cator must be stored in the MMI
¢page 266 .
Decorative wheel covers
Applies to vehicles: with decorative wheel covers
T he decora tive wh eel covers must be removed
first to access the wheel bolts .
Fig. 206 Changing a w hee l: Re movin g the w heel cove r
Removing
.,. Inse rt the hook (provided with the ve hicle
tool kit ) in t he hole in the wheel hub cove r. ..
Pull off the
decorative wheel cover
¢fig . 206.
Wheels with wheel bolt caps
Applies to veh icles: w it h w heel bolts with caps
The ca ps must be removed first from the
wheel bolts before the bolts can be un­
screwed.
Fig . 20 7 Cha ng ing a w heel: re m oving t he w hee l b o lt
caps
Removing
.. Push t he plastic clip (provided with the ve­
hicle tool kit) over t he wheel bolt cap u nti l
the inner reta iners on the clip a lign with the
edge of the cover.
.,. Remove the cap wit h the
plastic clip (veh i­
cle tool kit)
¢ fig . 207 .
Refitting
.. Place the caps over the whee l bolts and
push them back o n.
The caps are to protect and keep the wheel bo lts clean .

Loosening and tightening the wheel
bolt s
The wheel bolts must be loosened before rais­
ing the vehicle.
F ig. 208 Changing a whee l: loos enin g the wh eel bo lt s
Loo sening
.. Slide the whe el w re nch onto the wheel bolt
as far as it wi ll go .
.. Take tight hold of th e
end of the wrench
hand le and turn the whee l bolts
counte r­
clock wis e
abou t one single turn in the direc­
tion of arrow c:>
fig. 208 .
Tightening
.. Slide the wheel wrench onto the whee l bolt
as far as it will go.
.. Take tigh t hold of the
end of the wrench
handle and turn each wheel bolt
cl ockw ise
unt il it is seated .
A WARNING
-Do not use force or hurry when changing
a whee l -you can cause the vehicle to s lip
off the jack and cause ser ious persona l
injuries.
- Do not loosen the wheel bolts more than
one turn
before you ra ise the veh icle w ith
the jack. -You risk an injury.
(D Tips
- Never use the hexagonal socket in the
handle of the screwd rive r to loosen or
tighten the wheel bo lts.
- If a whee l bolt is very tight, you may find
i t easier to loosen by c arefully p ushi ng
down on the end of the whee l bolt
wrench with
one foot only . As you do so,
What do I d o now ? 271
hold on to the car to keep your balance
and take care not to slip .
Raising the vehicle
The vehicle must be lifted with th e jack first
before the wheel can be removed.
F ig . 209 Sill panels : ma rki ngs
Fig . 210 Sill : p os it ion ing t he ve hicle jack
.. Act iv ate the vehicle jack mode* in the MMI:
!CAR I function button> (Car) * sy stems con­
trol button>
S e rv icing & ch ecks > Air su sp .:
jack mode > On .
.,. Engage the park ing brake to prevent your
veh icle from rolling unintentionally .
.,. Move the
s elect or le ver to p osition P .
.,. Find the marking (imp rint) on the sill tha t
is nearest the wheel that wi ll be changed
r=> fig. 209 . Behind the marking, there is a
lifti ng p oint on the sill for the veh icle jack .
.. Veh icles wi th a s ill: remove the cover from
the sill before lift ing the veh icle wi th a vehi­
cle jack
c:> page 272 .
.,. Turn the vehicl e ja ck located under the lift­
ing point on the sill to ra ise the jack unti l its
arm @ c:>
fig. 210 is located under the des­
ignated p lastic moun t c:> &, c:>(D .
.. Align the jack so that its arm@c:>
fig. 210
engages in the designated lifting point in
the door sill and the movable base @ lies
~

272 What do I do n ow ?
flat on the ground. The base @ must be ve r­
tical under the lifting point @.
• Wind the jack up further until the flat tire
comes
off the ground <=>,& .
Position the vehicle jack
onl y under the desig­
nated lifting points on the sill~
fig. 209.
There is exactly one location for each wheel.
The jack must not be positioned at any other
locat ion <=> .&. <=>CD.
An
u ns table su rf ac e under the jack can cause
the vehicle to slip off the jack. Always provide
a firm base for the jack on the ground. If nec­
essary place a sturdy board or s imilar support
under the jack. On
h ard , s lipp ery su rf ac es
(such as tiles) use a r ubber mat or sim ilar to
prevent the jack from slipping ~,&. .
.&, WARNING
-You or your passengers could be injured
wh ile chang ing a whee l if yo u do not fol­
low these safety precautions:
- Position the vehicle jack only at the
des ignated lifting points and align the
jack . Otherwise, the vehicle jack could
slip and cause an injury if it does not
have sufficient ho ld on the vehicle.
- A soft or unstable surface under the
jack may ca use the vehicle to slip off
the jack. Always provide a fi rm base for
t he jack on the ground. If necessary,
use a sturdy board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or s imilar to prevent
the jack from slipping.
- T o help p revent injury to yourself and
your passenge rs:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not rema in in the ve­
h icle when it is jacked up.
- Make sure that passengers wait in a safe p lace away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad­ just as necessary and then continue to ra ise the jack. -
Changes in temperature or load can af­
fect the he ight of the vehicle .
(D Note
Do not lift the vehicle by the sill. Position
the vehicle jack only at the designated lift­ ing po ints on the sill. Otherwise, your vehi­
cle will be damaged .
(D Tips
The vehicle jack mode* switches off auto­
matically at speeds above 6 mph (10 km/
h).
Removing and installing the s ill cover
Applies to vehicles: wit h sill
Fig . 2 1 1 S ill: r emoving the cov er
,.. Pull the cover down to remove it ~fig. 211.
• To insta ll the cover again, insert it into the
retainers and t hen swing it upward until it
clicks into p lace. The cover must be flush
w ith the sill.
@ Tips
Some models may also have a cover for the
rear vehicle lift po int.

Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
Fig. 2 12 Changing a wheel: using the screwdriver han ­
dle (with the blade removed} to turn t he bo lts
F ig . 2 13 Changing a wheel: alignm en t pin ins ide the
top hole
After you have loosened a ll wheel bolts and
ra ised the veh icle off the ground, remove and
replace the wheel as follows:
R emoving the wheel
.. Use the hex agon al so ck et in th e scr ew dr iv­
e r handle
to comp letely remove the top­
most wheel bo lt and set it aside on a
clean
s u rface Q fig. 212 .
.. Screw the threaded end of the alignm ent
pin from the tool k it hand -tight into the
empty bolt hole
Qfig . 213.
.. Then remove the other wheel bo lts as de­
scribed above .
.. Take off the wheel leaving the alignment
pin in the bolt hole
Q (D.
Putting on the spar e wheel
.. Lift the spare wheel and carefully slide it
over the alignment pin to guide it in place
Q (D.
What do I d o now ? 273
.. Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bolts
slightly.
.. Remove the alignment pin and insert and
tighten the remaining wheel bolt slightly like the rest.
.. Turn the jack handle counter-clockwise to
lower the veh icle until the jack is fully re­
leased .
.. Use the wheel bo lt wrench to tighten all
wheel bo lts firm ly
Q page 271. Tighten
them
crosswise, from one bolt to the (ap­
proximately) opposite one, to keep the
wheel centered.
(D Note
When removing or installing the whee l,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you.
@ Tips
Never use the hexagonal socket in the han ­
dle of the screwdriver to loosen or tighten
the w heel bolts.
- Pull the reversible blade from the screw­
dr iver before you use the hexagonal
socket in the hand le to turn the wheel
bolts.
- When mounting tires w ith
unidi rectional
tread design
make sure the tread pat­
tern is po inted the right way
~page 274.
-The wheel bo lts shou ld be clean and easy
to turn . Check for dirt and corrosion on
the mating surfaces of both the wheel
and the hub. Remove all d irt from these
surfaces before remounting the whee l.

274 What do I do now? Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Using a spare tire w ith a tread pattern
intended for use in a specific direction
When using a spa re tire w ith a t read patte rn
i n tended fo r use in a specific direction, please
note t he followi ng:
- The direction of rotation is marked by a n ar­
r ow on the side of the tire.
- If the spare t ire has to be installed in the in­
correct direction, use the spare tire only
tempora rily si nce the t ire will not be a ble to
achi eve its optimum perfo rm anc e cha racter­
i st ics w ith reg ard t o aqu aplani ng, noise and
we ar.
- W e reco mmend t hat you pay pa rticular at­
te nti on t o this fact d uring wet we ather and
t h at you a dju st yo ur spee d to m atc h ro ad
con ditions.
- R epl ace the fla t tire w ith a n ew one an d
have it ins talled o n your ve hicle as soon as
p oss ible to restore the handlin g ad vantages
of a uni direct io na l tire .
Notes on wheel changing
Please rea d the informati on c> page 257 , New
t ires and replacing tires and wheels
if you are
go ing t o u se a spare tire which is d ifferent
from the tires on your ve hicle.
Afte r you chan ge a t ire :
-Check the tire pressure on the spare imme­
diately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as possible by your authorized Audi dealer or
a qualified service station.
- With steel and alloy wheel rims , the wheel
bolts are correctly tightened at a torque of
90 ft lb (120 Nm ).
- If you notice that the wheel bolts are cor­
roded and difficult to turn while changing
a tire, they should be replaced before you
check the tightening torque . -
Replace the flat tire with a new one and
have it installed on your vehicle as soon as
possible. Remount the wheel cover .
Until then , drive with extra care and at re­
duced speeds.
A WARNING
-
- If you are going to e quip your ve hicl e
with tires or rims which differ from those
which were facto ry installed, then be
sure to rea d the informati on
9 page 257,
New tir es and replacing tires and
w he els .
- Always ma ke sure the damag ed wheel o r
even a flat tire and the jack a nd tool ki t
ar e prop erly s ecu red in the luggage co m­
p artm ent and are not lo ose in the pas ­
s e ng er c ompa rtm ent .
- I n an acci dent or sudd en man euve r they
could fly forwa rd, inju ring anyon e in the
v eh icle.
- Always store d amag ed wh eel, jack and
too ls secur ely in the lugg age c ompart ­
ment. Otherwi se, in an accident or su d­
de n maneuve r they co uld fly forw ard,
causing inj ury to passe ngers i n the ve hi­
cle.

Data
Data
A7 Sportback 310 hp., 3.Q, liter 6-cylinder engine
Applies to vehicles: with 3.0 liter 6-cyli nde r engine and all-wheel d rive
Engine data
Maximum output SAE net
Maximum torque SAE net
No . of cylinders
Displacement
Stroke
Bore
Compression ratio
Fuel
Dimensions (approx .)
L eng th (wit h license pl ate brac ket)
Width (across mirrors) He igh t (unloaded) hp@
rpm
lb-ft@ rpm
C ID (cm
3
)
in (mm)
in (mm)
-- ,
__ ...
310@ 5500-6500
325 @ 2900-4500
6
182 (2995)
3.50 (89 .0)
3 .33 (8 4.5)
10 .3 : 1
Premium unleaded (91 AKI) Recommended for maxi­
mum engine performance. Further details
Qpage 225,
Gasoline
in (mm) 1 95.6 ( 4969)
in (mm) 84.2 (2139)
in (mm) 55.9 (1 420)
Turning circle diameter (curb to curb) ft. (m) 39. 0 (11.9)
Capacities (appro x.)
Fuel tank
- Total capacity
- Reserve (o f to tal capacity)
Windshield fluid container
Windshield and headlight washer
fluid container *
Engine oil
with filter change gal (liters)
19.8 (75.0)
g
al (li ters) 2. 6 (10.0)
quarts (liters) 3.7 (3.5)
qu arts ( liters) 5 .2 ( 4.9)
quarts (lite rs) 7.2 (6.8)
287
•
•

288 Data
S7 Sportback 420 hp, 4.0 liter a-cylinder engine
Applies to vehicles: with 4.0 liter 8-cylinder engine and all-wheel drive
Engine data
Maximum output SAE ne t
Maximum torque SAE net
No. of cylinders
Stroke
Bore
Compressio n ratio
Fuel
Dimensions ( approx .)
Leng th (with lice nse pl ate bra cket)
Width (across mirrors) He igh t (unloaded) hp@ rpm
lb-ft@ rpm
CID (cm
3 )
in (mm)
in (mm)
__ ,
-~ .. ,
420 @ 5500-6400
406@ 140 0-5200
8
24 3 .67 (3993)
3 .50 (89 .0)
3 .33 (84.5)
10 .1: 1
Premium unleaded (91 AKI) Recommended for maxi­
mum engine performance . Further details¢
page 225,
Gasoline
in (mm) 1 95.6 (4969)
in (mm) 84.2 (2139)
in (mm) 55.9 (1 420)
Turning circle diamet er (curb to curb) ft . (m) 39 .0 (11.9)
Capacities (appro x.)
Fuel tank
- Total capacity
- Reserve (o f to tal capacity)
Windshield fluid container
Windshield and headlight wa sher
fluid container *
Engine oil
with filter c hange gal (li
ters)
19 .8 (75 .0)
gal (li ters) 2. 6 (10. 0)
q uarts (lit ers) 3 .7 (3 .5)
qu arts ( li1ters) 5 .2 ( 4.9)
quarts (li te rs) 8 .8 (8.3)

29 0 Con sum er Inf ormation
comp lexity of today's automobi les, have
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Also, s afety an d e nvir onm ent al con­
cerns place very strict limits on the nature of repairs and adjustments to engine and trans ­
miss ion pa rts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing devices and oth­
er equipment avai lab le to specially trained
workshop personnel in order to assure proper
performance, reliab ility and safety of the vehi­
cle and its many systems .
Improper ma intenance, adjustments and re ­
pa irs can impair the operation and reliab ility
of your vehicle and even void your vehicle war­ ranty. Therefo re , proof of servici ng in accord­
ance w it h the ma intenance sched ule may be a
condition for upholding a poss ible warranty
claim made within the warran ty period.
Above all, operational safety can be adve rsely
affected, creating unnecessary risks for you
and your passengers.
If in doubt about any serv icing, have it done
by your author ized Audi dealer or any other
p roperly equipped and qualified workshop .
We strong ly urge you to give your authorized
Audi dealer the opportunity to perform all
schedu led maintenance and necessary repairs .
Your dea ler has the facilities, or iginal parts
and tra ined spec ialists to keep your vehicle
running properly .
Performing lim it e d m aint en anc e y ourself
The fo llowing pages describe a limited num­
ber of procedures which can be performed on
you r vehicle with ordinary too ls, shou ld the
need arise and trained personnel be unavaila­
ble. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and ca refully follow the instruc­
tions given. Always rigorously obse rve the
WARNINGS p rovided .
Before you ch eck anything in th e engin e
compartme nt, alway s read an d heed all WARNINGS
¢ & a
nd ¢ & in Working in the
engine comportment on page 230 .
A WARNING
--Serious personal in jury may occur as a re-
sult of improperly performed mainte­ nance, adjustments or repa irs.
- Always be extremely careful when work­
ing on the vehicle. Always follow com­
monly accepted safety pract ices and gen­
eral common sense. Never r isk personal
in jur y.
- Do not attempt any of the maintenance,
checks or repairs descr ibed on the fol­
lowing pages if you are not fu lly fam iliar
with these or other procedures with re­ spect to the vehi cle, or are uncerta in how
to proceed .
- Do not do any work withou t the proper
too ls and equipment . Have the necessary
work done by your authorized A udi deal ­
er or anothe r properly equipped and
qualified workshop.
- The engine compar tment o f any motor
vehicle is a potentially hazardous area. Never reach into the area around or
touch the rad iator fan. It is temperature
control led and can sw itch on suddenly -
even when the engine is off . The radiator
fan switches on automatically when the
coo lant reaches a certain temperature
and will cont inue to run until the coo lant
tempera ture drops.
- Always sw itch off the ignition before any­
one gets under the vehicle.
- Always support your veh icle with safety
s tands if it is necessary to work under­
neath the vehicle. The j ack s upp lied with
the vehicle is not adequate for this pur­
pose and cou ld co llapse causing serio us
pe rsonal injury .
- If you must work underneath the vehicle
with the wheels on the ground, a lways
make sure the vehicle is on leve l ground,
that the wheels are a lways secure ly
blocked and that the engine cannot be
started .

29 4 Index
A
Accessories . . . . . . . . . . . . . . . . . . . . . . . . 2 9 1
Active lane ass ist ... ... .. .. .. .. .. .. .. 95
Activating and deactivating . . . . . . . . . . . 96
C leaning came ra area ... .. .. .. .. .. . 216
Descr ipt ion ... ........... .. .. .... .. 95
I nstrument cluster indicator light . . . . . 96
Messages . . . . . . . . . . . . . . . . . . . . . . . . . 96
Notes on instrument cluster display . . . . 96
Setting the steering wheel vibrat ion . . . . 97
AC (automatic cl imate control) . .. .. .. .. 71
AC (climate control) . . . . . . . . . . . . . . . . . . 69
Adaptive air suspension/sport . ... .. .. . 102
Adapt ive cruise control . . . . . . . . . . . . . . . . 86
C leaning sensors/cameras .. .. .. .... . 216
Messages ............... .. .. .. .. .. 93
Request for driver intervention . . . . . . . . 91
Stop-and-go traffic . . . . . . . . . . . . . . . . . 90
Adapt ive Lig ht (defective) ... .. .. .... .. 22
Adding Eng ine coolant ............. .. .... . 238
Eng ine oil .. ..... ........... ... .. . 235
W indshield washer fluid .. ... .. .. .. . 244
Additives Eng ine oil ............... .. .. .. .. . 235
Ad justing
Air distribution (automatic climate con-
trol) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
air distribution (climate control) . .... .. 69
Front seats . . . . . . . . . . . . . . . . . . . . . . . . 52
Instrument illum inat ion ... .. .. .. .. . . 46
Steer ing column electrically .. .. .. .. . . 74
Steer ing column manually ..... .. .... 74
Tempe ratu re (automat ic climate control) 72
Tempe ratu re (climate control) .. .. .. . . 69
A irbag system . . . . . . . . . . . . . . . . . 149, 170
Advanced Airbag System ... .. .. .. .. . 153
Advanced Airbag System components . 157
Care ....... .......... ...... ... .. . 165
C hi ldren . ............... .. .. .... . 177
C hi ld restra ints ........... .. .. .. .. . 177
Components (front airbags) . .... ... . 15 7
Danger of fitting a child seat on the front
passenger seat . . . . . . . . . . . . . . . . . . . . 151
Disposa l . . . . . . . . . . . . . . . . . . . . . . . . . 165
Front airbags . . . . . . . . . . . . . . . . 153, 155
H ow do the front airbags work? . .... . 159 How many a
irbags does my vehicle
have? . ... .... .. .. ... .. ..... ... .. 157
How the Advanced Airbag System com -
ponents work together ......... .... 159
Important safety instructions on the
knee airbag system ................ 168
Important things to know . .. .. .. .. .. 149
Knee airbags . .. .. .......... ...... . 166
Monito ring .. .. . .. ............ .. .. 161
PASS ENG ER A IR BAG OFF light ... .. .. 162
Repairs ... .... .. .. ... .. . .... ... .. 165
Safety instr uctions . .. .. ..... .... . .. 164
Side airbags ..... .. ... ..... ... .. .. 169
S ide curtain airbags . . . . . . . . . . . . . . . . 172
Warning/ind icator lights ........ .... . 19
Warning/Indicator lights ....... .... 161
When must the system be inspected? 161
Aircraft Transporting your vehicle ..... .. .. .. 283
All-wheel drive .. .. ............. .... 201
Win ter tires . .. . .. ............ .. .. 261
Alloy wheels .. .. .. .......... ...... . 218
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Amb ience lighting ................ ... 46
Anti-freeze
refer to Eng ine coolant ............ . 237
Anti- lock braking system . ..... ... .. .. 196
Warning/ind icator lights ........ .... . 20
An ti-s lip reg ulation ............. .. .. 196
Anti-theft systems Electronic immob ilizer ............. .. 33
Ashtray . ... .... .. .. ... .. ..... ... .. . 58
Audi braking guard
refer to b rak ing guard .......... .... . 86
Audi drive select
refer to drive select ............... . 102
Audi Serv ice Repair Manuals and Litera-
ture ... .... .... .. ............. .... 289
A UTO
automatic climate contro l . . . . . . . . . . . . 72
Automatic headlights ... .... ... .. .. . 43
climate control ... .. ... ..... ... .. .. . 69
A uto Lock . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Automat ic be lt retractor ........... .. 143
A utomatic car wash . .... ..... ... .. .. 214

Index 295 ____________________________ ...:.:..:.=.:::.::.:
Automatic climate control
Air vents ... ................ ... .... 72
Automatic recirculation . . . . . . . . . . . . . . 73
Operation ................... .. ....
71
Setup ... ..................... .... 73
synchronizing . ........ ... ... ... ... . 72
Automatic Shift Lock (ASL) ... ... .. .. .
110
A t t· t . .
u oma 1c ransm1ss1on ....... .. .. .. . 109
Automatic Shift Lock (ASL) . .. .. .. .. . 110
Driving .. .. ............. .. .. .. .. . 111
Emergency mode ............ ... .. . 114
Emergency release . . . . . . . . . . . . . . . . . 115
Kick-down . ................. ... ... 113
Manual shift program ..... .. .. .. .. . 113
Selector lever . . . . . . . . . . . . . . . . . . . . . 109
Automatic wipers ................ .... 47
Auto Safety Hotline ......... ... ... ..
138
Average consumption ....... .. .. .. .. .. 25
Average speed . . . . . . . . . . . . . . . . . . . . . . . 25
Avoid damaging the vehicle ...... ... .. 205
B
Bag hooks . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Brake system
Anti-lock braking system .............
20
Brake assist system ................ 196
Brake booster .. .. ................. 200
Brake fluid .. .. .. .... ............. 239
Brake fluid specifications for refill and re ­
placement . . . . . . . . . . . . . . . . . . . . . . .
240
Brake light defective . . . . . . . . . . . . . . . . 22
Brake pads .... .. .. . ..............
204
Electromechanical parking brake ... .. . 78
Fluid reservoir ... .. ...............
239
How does moisture or road salt affect the
brakes? ....... .... ...............
199
Warning/indicator lights ........ .... . 15
Worn brake pads symbol ............ . 21
braking guard
Settings ... ... .... ................
93
Braking guard ..... .. ................ 86
Messages . .. .. .. .... ........... .. . 93
Break-in period .. .. .. ............... 204
Brake pads .. .. .. .... ... .... .... .. 204
Tires
Bulbs
....... ..... .. ...............
204
278
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . .
240 C
Charging ... ................ ... ... 243
Important warnings ......... ... .. . 241
Jump starting ..................... 279
Location . .. ............. .... .. ...
241
low . .. ... . .... ............. .. .. . 202
Replacing the battery . . . . . . . . . . . . . . 244
State of charge .............. .... .. 202
Winter operation ............ .... .. 240
Working on the battery .... .. .. .. .. . 241
Before driving .. ........... .. .. .. ... 130
Blended gasoline ................... 225
Blower (automatic climate control) . . . . . . 72
Blower (climate control) . . . . . . . . . . . . . . .
69
Body cavity sealing ......... .. .. .. .. . 219
Booster seats ..... .. ...... .. .. .. .. . 184
Brake fluid
Changing the brake fluid ........... .
240
Checking the brake fluid level . .. .. .. . 239
What is the correct brake fluid level? .. 239
What should I do if the brake fluid warn-
ing light comes on? .......... .. ....
239
California Proposition 65 Warning ..... 231
Battery specific . . . . . . . . . . . . . . . . . . . 242
Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 287
Engine oil ... .. .. .................
232
Car care .... .. .. .. ................. 213
Exterior ......... .. ..... .......... 213
Interior ... .. .. .. .. . .. .... ........ 219
Car carrier
Transporting your vehicle ....... .. .. 283
Cargo area ... ..... .. ...............
136
Cargo net . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Catalytic converter ... .............. . 205
Center armrest
Cockpit ... .. .. .. ................. .
54
Central locking .. .... ... ....... ...... 34
Emergency locking .. ... ....... .... .. 38
Certification .. .. .. .................
292
Changi ng a wheel .. .... ......... .... 269
Changing engine oil .. ... ....... .... .
236
Chassis (undercoating) . . . . . . . . . . . . . . . 219
•
•