wheel AUDI S7 2014 Repair Manual

200 Intelligent technology
Braking
General information
What affects braking efficiency?
Operating conditions and driving habits
The brakes on today's automobi les are sti ll
subject to wear, depending largely on operat­
ing conditions and driving habits
c:> ,&. On
vehicles that are either driven mostly in stop­
and-go city traffic or are driven hard, the brake pads should be checked by your author­
ized Audi dealer more often than specified in
the
Warranty & Maintenan ce booklet . Failure
to have your b rake pads inspected can result
in red uced brake performance.
On steep slopes, you shou ld use the brak ing
effect of the engine. This way, you prevent un­
necessary wear on the brake system. If you
must use yo ur brakes, do not hold the brakes
down continuously. Pump the brakes at inter­
va ls.
Moisture or road salt
Unde r certain conditions, for example, when
driving through water or very heavy rain, or
even after washing your vehicle, the braking
effect can be red uced due to moisture (or in
freezing conditions ice) on the brake pads. A
few careful brake applications should dry off the brake pads or remove any ice coatings.
When you are driving at higher speeds with
the windshield wipers on, the brake pads will
briefly touch the brake discs in regular inter­
vals so as to improve reaction t ime when brak­
ing on wet surfaces. You the driver will not no­
tice anything .
The effectiveness of the brakes can be reduced
when the vehicle is dr iven on a salt-covered
road and the brakes are not used . Here too,
you should clean off accumulated salt coat ing
from brake discs and pads with a few careful
applications of the brake
c:> ,& .
Corrosion
There may be a tendency for dirt to build up
on the brake pads and corrosion to form on the
discs if the car is not driven regu larly or
o n Ly for short trips with litt le use of the
brakes.
If the brakes are not used frequently, or if cor­
r osion has formed on the discs, it is advisable
to clean off the pads and discs by braking
firmly a few times from a moderately h igh
speed
c:> .&. .
Faults in the brake system
If you shou ld notice a sudden increase in
brake pedal travel, then one of the two brake
circuits may have fai led
c::> .&. .
Low brake fluid level
Malfunctions can occu r in the brake system if
the brake fluid level is too low. The brake fluid
l evel is monitored electronically.
Brake booster
The brake booster works with vacuum pres­
su re which is created only when the eng ine is
running
c::> ,& .
Brake lining wear status
Brake lining wear may be checked by visual in­
spect ion of the condition of the brake pads
t hr ough the open ings in the wheel. If neces­
sary, the wheel may be removed for this in­
spect ion
c:> page 266, Changing a wheel.
.8_ WARNING
-You shou ld perform braking maneuvers
for the purpose of cleaning the brake
system only if road conditions permit.
Other road users must not be put at risk -
you may cause an accident!
- Before descending a steep grade, reduce
speed and sh ift transmission into a lower
gear or lower driving range. Do not ride
the brakes or hold the pedal down too
long or too often . This could cause the
brakes to get hot and diminish braking
efficiency.
- Do not "ride the brakes" by resting your
foot on the pedal when you do not intend
to brake. This may cause the brakes to

overheat, premature wear and increased
stopp ing distance.
- Under certain climatic and operating
conditions such as passing through wa­
ter, driving in heavy rain or after wash ing
the vehicle, the effect iveness of the
brakes can be reduced. In winter, ice can
accumulate on the brake pads, linings,
discs and drums. Carefully apply brakes
for a test. Brakes will dry and ice coat­ ings will be cleaned off after a few ca re­
f ul brake applications.
- Driv ing for an extended period of time on
salt-covered roads w ithout using your
brakes can also affect braking efficiency.
Clean off accumulated salt coating from
brake discs and pads w ith a few caref ul
brake applicat ions.
- If you damage the front spoiler, or if you
install a different spoiler, be sure the air
flow to the front brakes is not obstruct­ ed. Otherwise the brake system could
overheat reducing the effectiveness of
the ent ire brake system.
- Failure of one brake c ircuit will impair
the braking capability resulting in an in­
c reased stopp ing distance. Avoid driv ing
the vehicle and have it towed to the near­
est Aud i dea ler o r q ualified workshop.
- Never let the vehicle roll to a stop w ith
the engine shu t off.
- If the brake booster is not work ing, the
brake pedal must be pressed conside ra­
bly harder to make up for the lac k of
booster assistance.
Electro-mechanical
power assist
The electro-mechanical power assist helps
the driver when steering.
Powe r steering adapts electronically based on
the vehicle speed.
Indicator lights and message s
• Steerin g defective! Stop th e vehicle
Int ellig ent technolog y 201
If this indicato r light turns on and stays on
and t his message appears, the power steering
may have failed.
Do
not con tinue dr iv ing . See your au thor ized
Audi dealer or other qualified repair facility
for assistance .
'I-Y Steering: System malfun ction! You may
c ontinue dri ving
If the indicato r light turns on and the mes­
sage appea rs, the stee ring may be more diffi­
c ult to move o r more sens itive than usual.
Drive slowly to your authorized Aud i dealer or
qualified workshop to have the ma lfunction
corre cted.
0) Tips
If the . or 1:z;lj indicator light on ly stays
on for a short t ime, yo u may continue dr iv­
i ng.
Driving with your
quattro
App lies to veh icl es: w ith all-w hee l drive
With all-wheel drive, all four wheels are driv­
en.
General information
Wi th a ll W heel Drive, power is distributed to
all four wheels . This happens automatically
depending on your driving style and the road
conditions at the time . See also
~ page 196.
With the sport different ia l* , power distribu­
tion to the rear wheels is variable and can be
adjusted with Audi dr ive select*
~ page 102.
Always read and follow safety precautions
~ .&. .
Winter tires
When dr iving in the winter, yo ur vehicle with
all-wheel drive has an advantage, even wit h
regular tires . In winter road conditions it may
be advisable to mount winter tires (or all-sea­
son tires) for improved driveability and brak­
ing: these tires must be moun ted o n
all four
wh eel s.
See also~ page 258, Winter tires. ..,.
•
•

202 Intellig ent technol ogy
Tire chain s
Where t ire cha ins are mandatory on certain
roads, this normally a lso applies to vehicles
with a ll- wheel drive
c::> page 259, Snow
chains .
Replacing wheels /t ir es
Vehicles with all-whee l drive must a lways
have tires of the same size. Also avoid t ires
with different tread depths. For details see
page
c::> page 2 54, New tires and replacing
tires and wheels.
Off -Ro ad dri ving?
Your Aud i does not have enough ground clear­
ance to be used as an off -road veh icle.
It is
therefore best to avoid rough tracks and un ­
even terrain as much as possible . Also refer to
c::> page206.
A WARNING
Always adjust your driving to road and traf­
fic condit ions. Do not let the extra safety
afforded by all-wheel dr ive tempt you into
taking extra r isks.
- Although the all-wheel dr ive is very ef­
fective, always remember that braking capacity is limited by t ire traction . You
should the refore not dr ive at excessive
speeds on icy or slippery road su rfaces.
- On wet road surfaces, be careful not to
dr ive too fast because the front wheels
cou ld beg in to s lide on top of the w ater
(aquaplaning) .
If this should occ ur, you
wi ll have no warning from a sudden in ­
crease in engine speed as with a front­
wheel drive vehicle. A lways drive at
speeds wh ich are suited to the road con­
ditions -risk of crash.
Energy management
Starting ability is optimized
Energy management controls the distribution
of electrical energy and thus optimizes the
availability of electrical energy for starting the engine.
If a vehicle with a conventional energy system
is not driven for a long per iod of t ime, the bat­
tery is discharged by idling current consumers (e .g. immobilize r). In certa in circumstances it
can resu lt in the re be ing insufficient energy
available to start the engine.
Intelligent energy management in your vehi­
cl e ha ndles the distribution of e lectr ica l ene r­
gy . Start ing ability is ma rkedly improved and
the life of the battery is extended .
Bas ica lly, energy management consists of
b att ery diagn osis, idlin g current manage ­
m ent
and dynamic en erg y manag em ent .
Battery di agnosis
Battery diagnosis continuously determines
the state of the battery. Sensors determine
battery voltage, battery cu rrent and battery
tempe rature. This determines the current
state o f charge and the power of t he battery .
Idling current management
Idling current management reduces energy
consumption while the vehicle is standing .
With the ig nition sw itched
off, it controls the
energy supply to the various electri ca l compo ­
nents. Da ta from ba ttery diagnos is is cons id ­
ered.
Depend ing on the batte ry's state of cha rge,
individual cons ume rs a re g radually turned
off
to prevent excessive discharge of the battery
and th us maintain starting capability.
Dynamic energy manag ement
While the vehicle is being d riven, dynamic en­
ergy ma nagement distr ibutes the energy gen­
era ted a ccord ing to t he needs of the individ u-
al components .
It regula tes consumption, so
t h at more electrical energy is not being used ..,.

Always apply brakes early. When driving
downhill, shift into a lower gear to use the en­
g ine braking effect to slow the vehicle . Use of
the brakes a lone can cause them to overheat
and fail.
Coolant temperature
The coolant temperature gauge ¢ page 11
must be observed carefully. The coo lant tem­
perature can increase if you drive on long in­
clines in a low gear at high engine speeds. Re­
duce your speed immediately if the LEDs in
the top part of the display turn on .
For more information about indicator lights,
refer to.
c> page 17 .
A WARNING
Anyone not properly restrained in a mov­
ing vehicle is at a much greater risk in an
accident . Never let anyone r ide in your car
who is not properly wearing the restra ints
provided by Aud i.
Trailer towing tips
Important to know
Your vehicle hand les different ly when towing
-
a trailer because of the additional weight and
d ifferent weight distribution . Safety, perform­
ance and economy w ill greatly depend on how
carefully you load your trailer and operate
your rig .
Before you actually tow your trailer, practice
turning, stopp ing and backing up in an area
away from traffic . Keep practicing until you
have become completely familiar with the way
your veh icle-trailer comb ination behaves and
responds .
Backing up is diff icult and requires practice .
Backing up with a tra iler genera lly requires
steer ing action opposite to that when backing
up your vehicle without a trailer.
Maintain a greater distance between your ve­
hicle and the one in front of you. You will need
more room to stop. To compensate for the
Trailer towing 211
trailer, you wi ll need a larger than normal
turning radius.
When passing, remember that you cannot ac­
ce lerate as fast as you norma lly would be­
cause of the added load. Make sure you have
enough room to pass. After passing, allow
plenty of room for your trailer before chang­
ing lanes again.
Avoid jerky starts, sharp turns or rapid lane
changes.
(0 Tips
- Do not tow a trailer during the break-in
period of your vehicle.
- If you tow a trailer, your Audi may re­
quire more frequent maintenance due to
the extra load¢
page 285.
Parking on a slope
Do not pork on a slope with a trailer . If it can­
not be avoided, do so only after doing the fol­
lowing:
When parking:
"' App ly the foot brake .
.,. Have someone place chocks under both the
veh icle and the trailer wheels.
"' With chocks in place, slowly release the
brakes until the wheel chocks absorb the
load .
.,. Turn the wheels towards the curb.
.,. Apply the parking brake.
.,. Select the P selector lever posit ion.
When restarting after parking:
.,. App ly the foot brake.
.,. Start the engine.
.,. Select the D/S selector lever position .
.,. Release the parking brake and slowly pull
out and away from the wheel chocks.
.,. Stop and have someone retr ieve the wheel
chocks .
111>
•
•

212 Trailertowing
If you move the selector lever of the auto­
mat ic transm ission to P before app lying
the park ing brake and before blocking the
wheels, you may have to use mo re force
later to move the lever out of the P posi­
tion .

214 Vehicle care and cleaning
A WARNING
- Only wash the vehicle when the ignition
is off and follow the instructions from
the car wash operator to reduce the risk
of accidents .
- To reduce the r isk of cuts, p rotect your­
self from shar p meta l compone nts w hen
was hing t he unde rbody or the ins ide of
the whee l housings.
- Aft er washing the vehicle, the braking ef­
fec t may be de layed due to mo isture o n
the b rake ro to rs or i ce in the winter. The
brakes must be dried first with a few
careful brake applications.
(!;) Note
- If you wash t he vehi cle in a n automati c
car wash, yo u m ust fold the exterior m ir­
ro rs in to reduce the r is k of damage to
the mirrors. Power folding exte rior m ir ­
ro rs * must only be folded in and out us­
i ng the power folding function.
- To prevent pa int damage, do not wash
t h e ve hicle in direct sun light . -
To reduce the ris k of damage to the sur ­
face, do not use insect removing spong­
es, kitchen sponges or similar items.
- Matte finish painted veh icle compo­
nents:
- To reduce the risk of damage to the
surface, do not use polishi ng agen ts or
h a rd wax.
- Neve r use car wash cycles that apply
p rotective wax .
It can destroy the
matte fi nish effect.
- Do not plac e any stickers o r magnet ic
signs on vehicle parts pain ted w ith
matte fi nish paint. The paint cou ld be
d am aged when the stickers o r m ag nets
a re removed.
@ For the sake of the env ironment
O nly wash the ve hicl e in facili tie s sp e ci al ly
d esigne d for tha t purpose. This will re duce
the r is k of dirty wate r contam ina ted with
o il from entering the sewer system.
Cleaning and care information
When clea ning and cari ng for individua l vehi ­
cle components, refer to the following tab le .
The information contained there is simp ly rec­
ommendations. For quest ions or for compo- nents that are not listed, refer to an author­
ized Audi dea
ler or a qualified workshop . Also
fo llow the information found in c> ,& .
Cleaning exterior
Component Situation Solution
Wiper blades
Dirty <=> page 49, Cleaning windshield wiper blades
Headlights/ D irty Soft sponge wi
th a m ild soap so lutiona l
tail lights
Sensors /
Dirty Sensors: soft cloth w ith a so lvent-free cleaning product
camera lense s Camera lenses: soft cloth with an alcohol-free cleaning
so lution
Snow/ice Hand brush/so lvent-free de-icing spray
Wheels Road sa lt Water
Brake d ust Acid-free special cleaning solution
Exhaust tail Road s alt Water, deani ng sol ution suit able for stainless s teel, if
pipes necessary

Tires and wheels
Tires
General notes
Tires may be the least appreciated and most
abused parts of a motor vehicle .
Tires may be the least appreciated and most
abused parts of a motor vehicle . Tires are,
however, one of the most important parts of a
vehicle, particularly considering the compara­
tively small patch of rubber on each tire that
assures that a ll- important contact between
you, your vehicle and the road.
Maintaining the correct tire pressure, mak ing
sure that your vehicle and its tires do not have
to carry mo re weight than they can safely han­
d le, avoiding damage from road hazards and
r eg ularly inspect ing t ires for damage i nclud­
ing cuts, slashes irregu la r wear and ove rall
condition are the most important things that
you can do to he lp avoid sudden tire failure in­
cluding tread separat ion and blowouts.
A voidin g damage
If you have to d rive over a curb or similar ob­
stacle, drive very slow ly and as close as possi ­
b le at a right angle to the curb.
A lways keep chemicals includ ing grease, o il ,
gasoline and brake fluid off the t ires .
I nspect the t ires regularly for damage (cuts,
cracks or b listers, etc.). Remove any fo reign
bod ies embedde d in the treads.
Storing tires Mark tires when you remove them to indicate
the direction of rotation . T his ensures you to
be ab le to mount them correctly when you re­
i nstall them .
When removed, the wheels or t ires should be
sto red in a cool, d ry and preferably dark place .
Store tires in a vertical pos ition if they are not
mounted on rims, in a horizontal pos it ion if
they are mounted on rims .
Tires an d wheel s 243
New tires
New ti res have to be broken in¢& .
The tread depth of new t ires may vary, accord­
ing to the type a nd make of t ire and the tread
patte rn.
H idden damage
Damage to tires and r ims is ofte n not readily
visible . If you notice unusual v ib rat ion or the
vehicle pulls to one s ide, th is may ind icate
that one of the t ires has been damaged . T he
ti res m ust be chec ked immed iate ly by an au­
thorized Audi dea le r or q ua lified wor kshop .
Unidirectional tires
A un idirectional tire can be identified by ar­
rows on the sidewa ll, that po int in the direc­
tion the t ire is designed to rotate. You mus t
f ol low the specified di rection o f rotation . T his
is necessary so that these tires can develop
their optimum characteristics regarding grip, road noise, wear and hydrop laning resistance.
For more information
¢ page 271.
A WARNING
New tires or t ires that are o ld, worn or
damaged cannot provide maximum con­
trol and braking ability .
-
-New tires tend to be slippery and must
be broken in. To reduce the r isk of losing
control, a co llision and ser ious personal
in ju ries, d rive with special ca re for the
fi rst 350 m iles ( 560 km).
- Driving with worn or damaged tires can
lead to loss of control, sudden tire fail­
ure, including a blowout and sudden de­
fl ation, cras hes and se riou s personal in­
juries . Have worn or damaged t ires re­
placed immediate ly.
- Ti res age even if they are not being used
and can fai l sudden ly, especially at hig h
speeds. Tires that are more than 6 years
old can only be used in an emergency
and then w ith special care and at low
speed.
•
•

24 4 T ire s and wheel s
-Never mount used tires on yo ur vehicle if
you are not sure of their "previous histo­
ry." Old used tires may have been dam­
aged even though the damage cannot be
seen that can lead to sudden t ire failure
and loss of vehicle control.
- If you notice unusual vibration or if the
vehicle pulls to one side when driving, al­
ways stop as soon as it is safe to do so
and check the wheels and tires for dam­
age.
(D Note
Please note that summer and winter tires
are designed for the cond itions that are
Glossary of tire and loading terminology
Accessory weight
means t he comb ined we ight (in excess of
those sta ndard items which may be rep laced)
of au toma tic tra nsmission, power steer ing,
power brakes, power windows, power seats,
radio, and heater, to the extent that th ese
items are availab le as factory -installed equip­
ment (whether installed or not) .
Aspect ratio
means t he ratio of the he ight to the w idth of
the tire in percent . Numbers of 55 or lower in ­
dicate a low sidewall for improved steering re­
sponse and better overall handling on dry pavement .
Bead
means the part of the ti re that is made of
steel wires, wrapped or reinforced by ply cords
and that is shaped to fit the rim.
Bead separation
means a b reakdown of the bond between
components in the bead.
Cord
means the strands forming the plies in the
tire . typ
ica l in those seasons . Audi recommends
using winter tires during the winter
months . Low temperatures signif icant ly
decrease the e lasticity of summer tires,
which affects tract ion and brak ing ability.
If summer tires are used in very co ld tem­
peratures, cracks ca n form on the tread
bars, res ulting in permanent tire damage
that can cause loud driving no ise and un­
balan ced t ires. Audi is not responsible for
th is type of damage .
Cold tire inflation pressure
means the tire p ressu re recommended by t he
vehicle manufacturer fo r a tire of a des igna ted
s iz e that has not bee n driven for more than a
coup le of miles (k ilometers) at low speeds in
t h e three hour period before the tire pressure
is measured or adjusted.
Curb weight
mea ns the we ight of a motor ve hicl e w ith
standard equipment including the max imum
capacity of fuel, oil, and coolant, air condi ­
tioning and additional weight of optiona l
equipment.
Extra load tire
me ans a t ire design to operate at higher loads
and at h igher inflation pressures than the cor­
responding standard tire . Extra load tires may
be identified as "XL", "x l" , "EXTRA LOAD", or
"RF" on the sidewall.
Gross A xle Weight Rating ("GAWR ")
means the lo ad -c a rry ing c apac ity of a s ingle
axle system , measured a t the tire-ground in­
terfaces.
Gross Vehicle Weight Rating ("GVWR ")
mea ns the maximum total loaded we ight of
t h e ve hicl e. .,.

Groove
means the space between two adjacent tread
ribs.
Load rating (code)
means the maximum load that a tire is rated
to carry for a given inflation pressure. You
may not find this information on all tires be­
cause it is no t req uired by law.
Maximum load rating
means the load rating for a t ire at the max i­
mum permissible inflation pressure for that
tire.
Maximum loaded vehicle weight
means the sum of:
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity weight, and
(d) Production options weight
Maximum (permissible) inflation pressure
means the maximum cold inflation pressure
to which a tire may be inflated. Also called "maximum inflation pressure."
Normal occupant weight
means 150 lbs. (68 kilograms) times the
number of occupants seated in the vehicle up
to the total seating capacity of your vehicle.
Occupant distribution
means distribution of occupants in a vehicle.
Outer diameter
means the overa ll diamete r of an inflated new
tire.
Overall width
means the linear distance between the exteri­
ors of the sidewalls of an inflated tire, includ ­
in g elevations due to labeling, decorations, or
protective bands or ribs.
Ply
means a layer of rubber-coated parallel cords.
Tires and wheels 245
Production options weight
means the combined weight of those installed
regular production options we ighing over 5
lbs. (2.3 kg) in excess of those standard items
which they replace, not previously considered
in curb weight or accessory weight, including
heavy duty brakes, ride levelers, roof rack,
heavy duty battery, and spec ial tr im .
Radial ply tire
means a pneumatic tire in which the ply cords
that extend to the beads are laid at substan­
tia lly 90 degrees to the center line of the
tread .
Recommended inflation pressure
see ¢ page 244, Cold tire inflation pressure.
Reinforced tire
means a t ire design to operate at higher loads
and at h igher inflation pressures than the cor­
re sp onding standard tire. Reinforced tires
may be identified as "XL", "xl", "EXTRA LOAD",
or "RF" on the sidewa ll.
Rim
means a metal support for a tire or a t ire and
tube assembly upon which the tire beads are
seated.
Rim diameter
means nom inal diameter of the bead seat. If
you change your wheel s ize, you will have to
purchase new tires to match the new rim di­
ameter.
Rim size designation
means r im diameter and width .
Rim width
means nominal distance between rim flanges .
Sidewall
means that portion of a tire between the
tread and bead.
•
•

246 Tires and wheels
Speed rating (letter code)
means the speed at wh ic h a tir e is des igned to
be d riven for extended per io d s of t ime. The
ratings range from 93 mph (150 km/h) to
186 mph (298 km/h)
¢ page 255. You may
not find this in format ion on all tires because
it is not required by law.
The speed rating letter code, w here a pplica­
b le, is molded on the tire s idewa ll and indi­
cates the maxim um permissible road speeds
¢ &. in Winter tires on page 259.
Tire pressure monitoring sy stem*
means a system tha t d etects when one or
mo re of a vehicle's t ires are under inflated and
i llum inates a low t ire p ress ure warn ing te ll­
tale.
Tread
means t hat port ion of a tire tha t comes into
con tact w it h t he road.
Tread separation
means pull ing away of the t read from the t ire
car cass .
Treadwear indicators (TWI)
means t he projections withi n the pr inc ipal
g rooves designed to give a v isua l ind ication of
the deg rees of wea r of the tre ad . See
¢
pag e 253, Tread W ear Indicator (TWI) for
mo re inf ormat io n on measu ring tire we ar.
Uniform Tire Quality Grading
is a tire i nfo rmation system developed by the
United States Nat io nal Highway Traffic Safety
Admin istration (N HTSA) that is designed to
h e lp buye rs make re lative compa risons among
tires. The UT QG i s no t a safety r ating and no t a
g uar antee t hat a t ire will las t fo r a presc ribed
n umber of m iles (kilome ters) or pe rform in a
certain way. It s imply gives ti re bu ye rs addi­
tional information to combine with other con -s
iderations, such as p rice , brand loya lty and
dealer recommendations. Un der UTQ G, tires
are grade d by the t ire manufacturers in three
areas : treadwea r, traction, and temperature
resistance. The UTQG informat ion on the tires,
molded into the sidewalls .
U.S. DOT Tire Identification Number (TIN )
This is the tire's "se ria l numbe r" . It be gins
with the letters "DOT" and ind icates that the
t ire meets all federa l standards . The next two
numbers or letters ind icate the plant where it
was ma nufactu red, and the last four numbe rs
r eprese nt the week and year of ma nufact ure.
Fo r exampl e,
DOT ... 2213 ...
means that the tire was produced in t he 22nd
wee k of 2013. The ot her numbers are market­
ing codes that may or may not be used by the
t ire manufacturer. This information is used to
contact consumers i f a tire defect requires a
r ecall .
Vehicle capacity weight
means the rated cargo and luggage load plus
150 lbs. (68 k ilograms) times the vehicle's to­
ta l seating capacity as listed on the label lo­
cated on the driver's side B-pilla r.
Vehicle maximum lo ad on the tire
means that load on an individua l tire that is
determined by distributing to eac h axle its
share of the maxim um loaded vehicle weight
and divid ing by two .
Vehicle normal load on the tire
means that load on an individua l t ir e that is
determined by distributing to eac h ax le its
share of the curb weight, accessory weight,
and normal occ upant weig ht (d istr ibuted in
accorda nce wit h tab le below ¢
page 247)
and divid ing by two .