battery AUDI S8 2010 Owner's Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2010, Model line: S8, Model: AUDI S8 2010Pages: 384, PDF Size: 90.95 MB
Page 291 of 384

___________________________________________ C..:...._ h:....:e :....:c:..:. k.::..: i..:.. n .:..:g:!:....:: a....:. n..:.. d~ f:....:. i.:..ll :.:.i:....:n :.:g !....- __
Closing the engine hood
- Pull the hood down until the pressure from the struts is
reduced.
- Let the hood
drop down and latch in place. Do not try to
push it shut;
it may fail to engage=:> &.
& WARNING
A hood that is not completely latched could fly up and block your
view while driving.
• When you close the engine hood, check it to make sure the
safety catch has properly engaged. The hood should be flush with
the surrounding vehicle body parts.
• If you notice while driving that the hood is not secured prop
erly, stop at once and close it. •
Working in the engine compartment
Be especially careful whenever you work in the engine
compartment.
Whenever you must perform any work in the engine compartment,
for example checking and filling different fluids, there is a risk of injury, burns and accidents. To prevent personal injury always
observe the following WARNINGS. The engine compartment of any
vehicle is a hazardous area=>& .
& WARNING
To help avoid injury, before you check anything under the hood:
• Turn off the engine.
• Remove the ignition key.
• Apply the parking brake.
Safety first
& WARNING (continued)
• Move selector lever to "P" (Park).
• Always let the engine cool down. Hot components will burn
skin on contact.
• To reduce the risk of being burned, never open the hood if you
see or hear steam or coolant escaping from the engine compart
ment. Wait until no steam or coolant can be seen or heard before
carefully opening the hood.
• Keep children away from the engine compartment.
• Never spill fluids on hot engine components. They can cause a
fire. • Never touch the radiator fan. The auxiliary electric fan is
temperature controlled and can switch on suddenly.
• Never open the coolant reservoir cap when the engine is still
warm. The coolant system is pressurized and hot coolant could
spray out.
• Protect your face, hands and arm from steam or hot engine
coolant by placing a thick rag over the cap when you open the
coolant reservoir.
• If work on the fuel system or the electrical system is necessary:
- Always disconnect the battery.
- Never smoke or work near heaters or open flames. Fluids in
the engine compartment could start a fire.
- Keep an approved fire extinguisher immediately available.
• To avoid electrical shock and personal injury while the engine is
running or being started, never touch:
-Ignition cables
- Other components of the high voltage electronic ignition
system.
• If you must perform a check or repair with the engine running:
- First, fully apply the parking brake, move selector lever to
"P" (Park). .,
Vehicle care Technical data
Page 292 of 384

___ C_h_ e_c _k _i_n -=g :a,__ a_n_ d_ f_ i_ l _li _n _,g;._ __________________________________________ _
& WARNING (continued)
-Always use extreme caution to prevent clothing, jewelry, or
long hair from getting caught in the radiator fan, V-belts or
other moving parts, or from contacting hot parts. Tie back hair
before starting, and do not wear clothing that will hang or
droop into the engine.
• Minimize exposure to emission and chemical hazards=:>
/1::..
& WARNING
California Proposition 65 Warning:
• Engine exhaust, some of its constituents, and certain vehicle
components contain or emit chemicals known to the State of Cali
fornia to cause cancer and birth defects and reproductive harm. In
addition, certain fluids contained in vehicles and certain products
of component wear contain or emit chemicals known to the State
of California to cause cancer and birth defects or other reproduc
tive harm.
• Battery posts, terminals and related accessories contain lead
and lead compounds, chemicals known to the State of California
to cause cancer and reproductive harms. Wash hands after
handling.
0 Note
When adding fluids, always make sure that they are poured into the
proper container or filler opening, otherwise serious damage to
vehicle systems wi ll occur.
ci> For the sake of the environment
To detect leaks in time, inspect the vehicle floor pan from underneath
reg ular ly. If yo u see spots from oil or other vehicle fluids, have your
vehicle inspected by an authorized Audi dea ler.•
Engine compartment
Applies to veh icles: w ith 8 -cylinde r engine
Engine compartment overview : a-cylinder
engine
These are the most important items that you can check.
Fig. 241 Typical layout for containers, engine oil dipstick and engine oil filler
cap
© Windshield/headlight washer container (0 ) ....... .
@ Brake fluid reservoir ( ) .................. .. .. . .
® Engine oil filler cap ('l=r.) ............ .. .... .. .. . .
© Engine oil dipstick (orange) .............. .. . ... . .
© Power steering reservoir . .. .. .. .. .. ... .... .. .. . .
© Coolant expansion tank (-L ) ........... .. .. .. .. . .
305
299
294
293
257
297 ..
Page 302 of 384

___ C_ h_e _c_ k_ i_ n ~ g~ a_ n _ d_ f_il _l _in _ g ____________________________________________ _
- Read the brake fluid level from the brake fluid reservoir
=> fig. 248 . T he brake fluid level mus t be between the
" M IN" and "MAX" markings.
The br ake fl uid re se rvoir is loc ated at the rear pa rt iti on of the engine
compartment on the left side~ page 290.
T he f lu id level may drop slightly after some time due to the auto
matic adjus tment of t he b rake pads. This is not caus e for alarm.
If the brake flu id leve l falls considerably below the "MIN" mark, t he
br ak e wa rning/ind ic ator lig ht ( U.S . model s:
BRAKE , Can adi an mod els:
«D> ) will come on~ page 20 and~ page 28. Do not continue to
operate the vehicle . The comple te brake system sho uld be thoro ughly
checked by an author ized A udi dealer or ot her qualified facility and
t he ca use correcte d. If the b rake fl uid leve l is too low, the bra ke
wa rning/in dicator light will illu mi nate . Con tact an au thorized Aud i
dealer
immediately .•
Changing brake fluid
H ave the brake flui d changed by an ex perienc ed techni
cian.
Brake flui d abso rbs mois ture from t he a ir . If t he wa ter con ten t in the
brake fl uid is too hig h, corros io n in the b rake system may res ult afte r
a period of time . The boiling po int o f the bra ke fl uid will also decrease
cons iderab ly and decrease brak ing perfo rmance.
The refore, the brake fl uid m ust be changed
every two years . Always
use new bra ke fluid w hich conforms to Fede ral Motor Veh icle St an
dard "FMVSS 116 DOT 4" .
Th e b rake fl uid reservoi r ca n be diffi cult to rea ch, there fore, we
recommend that you have the bra ke fluid c hanged by your author ized
Audi dealer. Your dea ler has the correct tools, the right b rake fl uid
and the know-how to do t his for you .
& WARNING
• Brake fluid is poisonous. It must be stored only in the closed
original container out of the reach of children!
• Brake failure can result from old or inappropriate brake flu id.
Observe these pre cautions:
- Use only brake fluid that meets SAE specification
J 1703 and
conforms to Federal Motor Vehicle Standard 116. Always che ck
with your authorized Audi dealer to make sure you are us ing
the correct brake fluid. The correct type of brake fluid i s also
indicated on the brake fluid reservoir .
- The brake fluid must be new. Heavy use of the brakes can
cause a vapor lock if the brake fluid is left in the system too
long . Thi s can seriously affect the efficiency of the brakes as
well as your safety . This could result in an accident.
0 Note
Brake fluid will damage the paint of your ve hicle .
~ For the sake of the environment
Because of the prob lem of proper disposal of brake fl uid as we ll as
the spec ia l too ls req uired and the necessary expe rtise, we recom
m en d that you have t he brake fl uid changed by your autho rized Audi
dea ler .•
Battery
General information
Under normal operat ing condit ions, the battery in your Aud i does not
nee d any m ain ten ance. Wi th high outs ide temper atures o r long d aily
dr ives we recommend that yo u have the elect rolyte level checked by .,_
Page 303 of 384

_____________________________________________ C_h _ e_ c_ k_in --= g'-- a_n _d_ f_i _ll _i_n -=g ::;__ ____.fflll
a service facility . The electrolyte level should also be checked each
time the battery is charged =>
page 303.
Have the batte ry checked when you take your vehicle in for serv ice .
You are well advised to rep lace a battery that is older than 5 years.
With certa in types of a irbag deployment, the ba ttery is disconnected
from the vehicle electrical system for safety reasons=>
& in "Repair,
care and disposal of the airbags" on
page 220.
Di sconne cting th e bat tery t ermina ls
Some vehicle f unct ions (power window regulators, fo r example) are
lost if the battery termina ls are disconnected . These functions have
to be re learned after the battery termina ls are connected aga in. To
prevent this, t he battery should only be disconnected from the
vehicle e lectr ica l system when absol ute ly necessary for repairs.
Vehicles not driven for long periods
If you do no t dr ive your veh icle over a period of severa l days or weeks,
electrical components are gradually cut back or switched off. Th is
red uces e nergy consumption and main tains sta rt ing capabili ty ove r a
longer period=>
page 258.
Be aware that when you unlock your vehicle, some of the convenience
functions may not operate, such as the Convenience key*, the remote
control or the power seat adjustment. The convenience functions will
be availab le aga in whe n you tur n on th e ignition and start the eng ine.
Winter operation
Dur ing the winter months, battery capac ity tends to decrease as
temperatures drop. This is because more power is also consumed
while starting, and the headlights, rear w indow defogger, etc., a re
used more often.
Avoid unnecessa ry power consum ption, part ic ula rly i n city traffic o r
when traveling only short distances. Let your authorized Audi dealer check the capacity of the vehicle battery before w inter sets in
=>
page 303 . A well charged battery will not only prevent start ing
prob lems when the wea ther is cold, but will also las t longe r.
Vehicle OP-eration
(I) Tips
If your vehicle is left standing fo r seve ral weeks at extremely low
temperatures, the vehicle battery should be removed and stored
w here it will not free ze. This will preven t it from being damaged and
having to be replaced. •
Working on the battery
Be especially careful when working on or near the
battery.
Vehicle care
Fi g. 2 49 Lugga ge
co mp artme nt: Righ t·
s ide stor age co mpar t·
me nt
Fig. 25 0 Lug gage
comp art me nt: Batt ery ~
Do-it-yourselt service iTechnical data
Page 304 of 384

., __ C_ h_ e_c _k _i _ n _g ~ a_n _d_ f_il _l_in _ g _________________________________________ _
The battery is located in the luggage compa rtment on the
right side beh ind a cover. Before you check anything in the
luggage compa rtmen t, read and heed all WARNINGS=>& .
- To open the side sto rag e com part me nt, turn the tw o pins
@ =>fig . 24 9 to th e vert ical position .
The positive( +) battery termina l is p rotected by a plastic cov er. This
cover must be removed to access the positive( +) terminal when
c onnect ing jumpe r cab les to sta rt the engine.
Always heed the safety warnings, when working on the vehicle
bat tery or the vehicle e lect ric al system to p revent injury .
The following WARNINGS are very important when
working on the battery:
Always heed the following WARNING SYMBOLS and safety pre cautions when working on the battery.
-
®
Always wear eye protection.
Battery acid contain s sulfuric acid. Always wear
gloves and eye protection .
No
- sparks
- flames
- smoking .
When a battery is charged, it p roduces hydrogen
gas which is explosive and could cause personal
injury .
Always keep the battery well out of reach of chil
dren .
& WARNING
Whenever working on the battery or on the electrical system,
there i s the ri sk of injury, a ccident and even fire. Read and heed
the following WARNINGS:
• Alway s wear eye protection . Do not let batt ery acid or any lead
part icles get on your skin or clothing. Shie ld your eyes. Explosive
ga se s can cause blindnes s or other in jury.
• Battery acid contains sulfuric acid. Sulfuric acid can cause
blindne ss and severe burns .
- Always wear gloves and eye protection . Do not tilt the
battery becau se acid could leak out of the ventilation open
i ngs.
- If you get battery acid in your eyes or on your skin, immedi
a tely rinse with cold water for several minutes and get medical
attention .
- If you should ingest any battery acid , see k medical attention
immediately.
• Do not expose the battery to an open flame, elect ric sparks or
an open light .
• Do not smoke.
• Do not interchange the positive and negative cables.
• When working on the battery, be sure not to short-circuit the
term inals with tools or other metal objects. This would cause the
battery to heat up very quickly, which could lead to damage or
e x plos ion and personal injury.
• When a battery is charged, it produce s hydrogen ga s wh ich is
e xplos ive and could cause pe rsonal inju ry.
• Alway s keep the battery well out of the reach of children .
• Before work is done on the ele ctrical system , disconnect the
negative ground cable.
• Before performing any work on the electrical sy stem , switch
off the engine and ignition as well as any electrical equipment.
The negative cable on the battery mu st be disconnected. If you are
~
Page 305 of 384

___________________________________________ C_ h_e _c _k_ i_n ~g_ a_n_ d_ f_ i_ll _i_n _g __ _
& WARNING (co ntinued )
just going to replace a light bulb , then it is enough to switch off
the lights .
• Before disconnecting the battery , switch off the anti-theft
alarm system! Otherwise you will set off the alarm.
• When disconne cting the battery, first disconnect the negat ive
cable and then the po sitive cable.
• Before reconnecting the b attery, make sure all electrical
consumer s are sw itched off. Reconnect the positiv e cable fir st and
then the negative cable . Never inte rchange the cables -this could
start a fire!
• Never charge a frozen or a thawed-out battery.
It could
explode! If a battery has frozen, then it must be replaced . A
di scharged batter y can freeze over at 32 °F (0 °C ).
• Make sure the vent hose is always attached to the opening on
the side of the battery .
• Never use batteries which are damaged. There is the danger of
an explosion! Alway s replace a damaged battery.
& WARNING
California Proposition 65 Warning:
• Battery posts , terminal s and related accessories contain lead
and lead compounds, chemicals known to the State of California
to cause cancer and reproductive problems. Wash hands after
handling.
0 Note
• Do not disconnec t the vehicle batte ry when t he ignit ion is
switched on o r when the engine is running, otherwise, you will
d amage e le ctro nic c ompone nts in t he ele ctrica l sys tem.
Safety first
• If your ve hicle is go ing to sta nd for a long per iod of time w it h out
bein g driven, protec t th e battery fro m "freezi ng", o therw ise i t wi ll be
damaged and will then have to be replaced .•
Battery charging
Sta rting t he e ng in e req uires a well c harged battery.
Always read and heed all WARNINGS b elo w =:> & and=:> &
i n "W orki ng on t he batt ery" o n
page 3 01.
- Turn off th e igni tio n and all electr ica l co nsum ers.
- Make su re the area is well vent ilated w hen you charge the
batte ry .
- Attach the red (posi tive
(B) c la m p of the charging equip
me nt to the posit ive te rmin al o f th e bat tery and t he b lac k
( n eg at ive(:)) clam p to t he jumper term inal.
- Only now plug t he m ain s lead for the c harg ing e quip ment
i n to t he wa ll outlet a nd tu rn it on=:> &.
- Make sure the charging rate is not over 30 amps/14.8
Volt.
- When the b attery is fully c harg ed: Turn t he ch arging
equ ip m ent off and remo ve t he mains l ead fr om the wall
ou tlet.
- Now remove the clamp s for the cha rging eq uipment .
A discharged ba ttery can freeze a t temperat ures of on ly O 0C. Allow a
frozen batte ry to thaw comp letely before attempting to charge it
=> & . However, we recomme nd not usin g a thawed battery aga in
because the battery casing can be cracke d due to ice formation and
c a n l eak battery a cid. .,._
Vehicle care Technical data
Page 306 of 384

lffll __ C_ h_ e_c _k _i _ n _g ~ a_n _d_ f_il _l_in _ g _________________________________________ _
Battery charging (Maximum charging rate of 30
amps/14.8 Volt )
When charging at /ow voltages (e.g . w ith a trickle charger ), th e
battery cab les do not have to be disconnected first. The batte ry caps
should
not be opened when cha rging a ba ttery .
It is not necessary to remove the battery from the luggage compart
ment, and i t is also no t ne cess ary to dis connect the cables.
Fast charging the battery (charging rate above 14.8
Volts)
For technical reasons do not use a battery cha rger that uses voltage
grea te r t han 14 .8 Vol ts to ch arge yo ur vehicle's ba tte ry .
& WARNING
Charging a battery can be dangerou s.
• Always follow the operating instructions provided by the
battery charger manufacturer when charging your battery .
• Never charge a frozen battery . It may explode be cause of g as
trapped in the ice . Allow a frozen battery to thaw out first.
• Do not reu se batteries which were frozen . The battery h ousing
may have cracked and weakened when the battery froze.
• Charge the battery in a well ventilated area. Keep away from
open flame o r elect rical spark. Do not smoke. Hydrogen gas gener
ated by the battery i s explosive.
• To reduce the danger of e xplosion , never connect or disconnect
c harger cable s while the charger is operating.
• Fast charg ing a battery is dangerous and should only be
attempted by a competent technician with the proper equipment .
• Battery acid that may spill during charging should be wa shed
off with a so lution of warm water and baking soda to neutralize
the acid.
0 Note
N ever use a fast cha rger as a booster to s tart the eng ine. This w ill seri
ously damage sensitive e lectronic components , such as control units,
re lays, ra dio, etc., as well as t he ba ttery cha rger. •
Battery replacement
The new battery must have the s ame specifications and
dim ensions as the original equipment b atte ry.
Inte lligent e nergy ma nagement in yo ur vehicle is responsib le for
distr ibuting the elect rical energy throughout your vehicle
~ page 258. T he intelligent energy management sys tem will keep
the eng ine battery charged better than vehicles without this system .
T o m ake s ure the addi tional e lectr ic al energy is available o nce aga in
after you have changed the battery, we recommend that you install
b atter ies of the same type and manuf actur e only ( the same as t hose
installed at the t ime you r vehi cle was delive red) . Specifications are
liste d on the ba ttery ho using. Your a uthorized Audi dealer w ill then
code the battery management control unit.
Th e new batte ry must have the same capacity, volta ge (12 vo lts),
ampe rage, const ruct io n and p lug sealing .
When installing the battery, make s ure the ign ition and all electrical
c ons umers are turned off.
0 Note
Mak e sure the vent ilat io n hose o n the side o f th e battery is
connec ted, otherwise fumes or battery acid can leak o ut.
<£> For the sake of the environment
Because of the prob lem of proper disposal of a ba ttery, we recom
mend you r auth o rized Audi dealer change the ba ttery for you.
Ba tte ries con tain sulfu ric acid and lead and must a lways be disp osed
~
Page 310 of 384

-~_T_ i_ re _ s_ a_n _ d_ w_ h _e_ e_ ls _________________________________________________ _
Groove
means the space between two adjacent tread ribs.
Load rating (code)
means the maximum load that a tire is rated to carry for a given infla
tion pressure. You may not find this information on all tires because
it is not required by law.
Maximum load rating
means the load rating fo r a tir e at the maximum permissible inflation
pressure for that tire.
Maximum loaded vehicle weight
means the sum of:
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity weight, and
(d) Production options weight
Maximum (permissible) inflation pressure
means the maximum cold inflation pressure to which a tire may be
inflated. Also called "maximum inflation pressure."
Normal occupant weight
means 150 lbs. (68 kilograms) times the number of occupants seated
in the vehicle up to the total seating capacity of your vehicle.
Occupant distribution
means distr ibution of occupants in a vehicle .
Outer diameter
means the overall diameter of an inflated new tire.
Overall width
means the linear distance between the exteriors of the sidewalls of
an inflated tire, including elevations due to labeling, decorations, or
protective bands or ribs.
Ply
means a layer of rubber -coated paralle l cords.
Production options weight
means the combined weight of those installed regular production
options weigh ing over 5 lbs. (2.3 kg) in excess of those standard
items which they replace, not previously considered in curb weight or
accessory weight, including heavy duty brakes, ride levelers, roof
rack, heavy duty battery, and special trim.
Radial ply tire
means a pneumatic tire in which the ply cords that extend to the
beads are laid at substantially 90 degrees to the centerline of the
tread .
Recommended inflation pressure
see=> page 307, "Cold tire inflation pressure".
Reinforced tire
means a tire design to operate at higher loads and at higher inflation
pressures than the corresponding standard tire. Reinforced t ires may
be identified as "XL ", "x l", "EXTRA LOAD", or "RF" on the sidewall.
Rim
means a metal support for a tire or a tire and tube assembly upon
wh ich the tire beads are seated .
Rim diameter
means nominal diameter of the bead seat . If you change your wheel
size, you w ill have to purchase new tires to match the new rim diam
eter .
Rim size designation
means rim diameter and width.
Rim width
means nom inal distance between rim flanges.
Page 323 of 384

Tires and wheels Ill
----------------
If you install rims, which do not have the sensors, or have sensors
w hich are not compa tible, then the tire pressure moni toring sys tem *
w ill not wo rk p roperly. I n this case, t he tire pressure monitor ing
system * wo uld not be ab le to monitor the tire pressure or warn yo u if
it is necessary .
• The battery inside of the tire pressure sensor has a limited service
l ife.
• Always dr ive wit h the
valve stem caps securely mo unted. We
recommend using factory ins ta lled
valve stem caps. As k your autho
r ized Audi dea ler to rep lace lost
valve stem caps .
Th e insta llation of repl acement tir es w ith s teel co rd bo dy plies in the
t ire sidewa ll may ca use ma lfunctio n of the tire pressure mo nitoring
system *, and is not recommende d (cord material informat io n i n
molded on the ti re s idewall).
Always check your tire pressure monito ring system* indicator afte r
re plac ing one or mo re tires on your vehicle. If the tire press ure m oni
to ring system* indicator flashes, or is on, your system is not working
pro perl y. Yo ur repla ceme nt tire might be incomp atible with your t ire
pressure monitoring system*, or some component of the tire pres
sure mon itor ing system * may be damaged.
& WARNING
• Using incorrect or unmatched tires and / or wheels or improper
tire and wheel combinations can lead to loss of cont rol, collision
and seriou s per sonal injury .
• Always use tires, rims and wheel bolts that meet the specifica
tions of original fa ctory-in stalled tires or other combination s that
have been specifically appro ved by the vehicle manufacturer.
• Tires age even if they are not being used and can fail suddenly ,
especially at high speeds. Tires that are more than 6 years old can
only be u sed in an emergen cy and then with special care and at
lowe r speeds.
• Never mount used tires on your vehicle if you are not sure of
their "previous history." Old used tires may have been damaged
Safety first
& WARNING (co ntinued )
eventhoughthedamagecannotbeseenthatcanleadtosudden
tire failure and loss of vehicle control.
• All four wheels must be fitted with radial tires of the same
type, size (rolling circumference ) and the same tr ead pattern.
Driving with different t ires reduces vehicle handling and can lead
to a lo ss of control.
• If the spare ti re is not the same as the tires that are mounted
on the vehicle - for example with w inter tires - only use the spare
tire fo r a sho rt pe riod of t ime and drive with extra care. Refit the
normal road wheel as soon as safely possible.
• Never drive faster than the ma ximum speed for which the tires
on your vehicle are rated because tires that are driven faster than
their rated speed can fail suddenly .
• Overloading tire s cause heat build-up, sudden tire failure,
including a blowout and sudden deflation and loss of control.
• Temperature grades apply to tires that are properly inflated
and not over or underinflated.
• For technical reasons it is not always possible to use wheels
from other vehicles - in some c ases not even wheel s from the same
vehicle model.
• If you install wheel trim discs on the vehicle wheels , make sure
that the air flow to the brakes is not blocked. Reduced airflow to
the brakes can them to overheat , increasing stopping distance s
and causing a collision.
• Run flat tires may only be u sed on vehicles th at were equipped
with them at the factory. The vehicle must have a chassis designed
fo r run flat tires and a factor y-in stalled tire pres sure monitoring
system* that indicates a loss of tire pre ssure. Incorrect use of run
flat tires can lead to vehicle damage or accident s. Check with an
authorized Audi dealer or tire specialist to see if your vehicle can
be equipped with run flat tires . If run flat tires are used , they must
be installed on all four wheels. Mixing tire types is not permitted . ..,_
Vehicle care Technical data
Page 350 of 384

111.___E_ m_ e_ r-' g=- e_n_ c=-y _ s_it _ u _ a_t_ i_ o _ n_ s ______________________________________________ _
Emergency situations
General
This section is intended for trained emergency crews and personnel
who have the necessary tools and equipment to perform these
operations. •
Starting by pushing or towing
0 Note
Your vehicle is equipped with an automatic t ransmission . Conse
quently, the e ngine ca nnot be started by push ing or tow ing .•
Starting with jumper cables
I f necess ary, the engine can be started b y connectin g it to
t he bat tery of another vehicle.
If the e ng ine shou ld fa il to start because of a discharged or weak
battery, the batte ry can be connected to t he battery of
another
veh icle, us ing a pair of jumper cables to start the eng ine .
Jumper cables
Use only jumper cables of suffic iently large cross section to carry the
sta rter cur rent s afely . Refer to the m an ufa ct ur er's specificat ions.
Use only j umpe r cab les with
insulated te rmi nal clamps wh ich are
distinct ly marked :
plu s(+) cable i n most cases colored red
minus (-) cable i n most cases colored black .
& WARNING
Batterie s contain el ectricity, acid, and gas . Any of the se can cause
very serious or fatal injury. Follow the inst ructions below for safe
handling of your vehicle 's battery.
• Always shield your eyes and avoid leaning over the battery
whenev er po ssible .
• A discharged battery can freeze at temperatures just below
32 °F (0 °C ). Before connecting a jumper cable, you must thaw the
frozen battery completely, otherwise it could explode.
• Do not allow battery acid to contact eyes or sk in . Flush any
contacted area with water immedi ately .
• Improper use of a booste r battery to start a vehicle may cause
an explosion .
• Vehicle batteries generate e xplosive gases. Keep sparks, flame
and lighted cigarettes away from batterie s.
• Do not try to jump start any vehicle with a low acid level in the
battery.
• The voltage of the booster battery must also have a 12-Volt
rating. The capacity (Ah) of the booster battery should not be
lower than that of the discharged battery . Use of batteries of
different voltage or substantially different "Ah " rating may cau se
an e xplosion and personal injury.
• Never charge a frozen battery . Gas trapped in the ice may cause
an explosion.
• Never charge or use a battery that has been frozen. The battery
c ase may have be weakened .
• Use of batteries of different voltage or substantially different
capacity (Ah) rating may cause an explosion and injury . The
capacity (Ah) of the booster battery should not be lower than that
of the discharged battery. .,_