wheel AUDI S8 2013 Owners Manual

276 What do I do n ow ?
ho ld on to the car to keep your ba lance
and take care not to slip .
Raising the vehicle
The vehicle must be lifted with the jack first
before the wheel can be removed .
Fig. 220 Sill panels : m ark ings
Fig . 22 1 Sill: posit ion ing t he veh icle jack
.. Activate the vehicle jack mode in the MMI:
I CAR ! function button > Ca r sys tem s control
button>
S ervicing & checks > Air susp .:
jack mod e > On .
.. Engage the parking brake to prevent your
vehicle from ro lling u ninten tionally.
.. Move the
se lector l ever to po siti on P .
.. Find the marking (imprint) on the sill that
is nearest the wheel that will be changed
o
fig. 220 . Behind the marking, there is a
lifting point on the s ill for the vehicle jack .
.. Turn the
ve hicle jack located under the lift­
ing point on the si ll to raise the jack until its
arm @o
fig. 221 is located under the des ­
i gnated plastic mount o ,& o0.
.. Align the jack so that its arm@o
fig. 221
engages in the designated lifting po int in
the door sill and the movable base @ lies
flat on the gro und. The base @ must be
ver­
tical
under the lifting point @. ..
Wind the jack up fu rther until the f lat t ire
comes off the ground o
.&,.
Position t he vehicle jack only under the desig ­
nated lifting points on the si ll
c:> fig. 220.
There is exactly one locat ion for each wheel.
The jack must not be positioned at any other location
c:> .&, c:>Q).
An un stable surfac e under the jack ca n cause
the vehicle to slip off the jack . Always provide
a firm base for the jack on the ground . If nec­
essary place a sturdy board or simi lar support
under the jack. On
hard, slipper y surfaces
(such as tiles) use a rubbe r mat or similar to
prevent the jack from slipping
c:> .&, .
A WARNING ~
-You or your passengers co uld be injured
while changing a wheel if you do no t fo l­
low these safety p reca utio ns:
- Position the vehicle jack on ly at the
designated lifting points and align the
jack. Otherwise, the vehicle jack co uld
slip and cause an injury if it does not
have sufficient hold on the vehicle.
- A soft or unstable surface under the
jack may cause the vehicle to slip off
the jack . Always prov ide a firm base for
the jack on the ground. If necessa ry,
u se a st urdy boa rd under the jack.
- On hard, s lippery su rface (such as t iles)
use a rubber mat or sim ilar to prevent
the jack from slipping.
- To help prevent injury to yo urself and
your p asse ngers:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic .
- Make sure jack pos ition is correct, ad ­
just as necessary and then continue to
raise the jack.
- Changes in temperature or load can af­
fect the height of the vehicle.

CD Note
Do not lift the vehicle by the sill. Position
the vehicle jack only at the designated lift ­
ing points on the sill. Otherwise , your vehi­
cle will be damaged.
(D Tips
The vehicle jack mode switches off auto ­
matically at speeds above 10 km/h .
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
Fig. 222 C h ang ing a w hee l: u sing t he sc rew drive r han ­
d le (w it h th e blade remov ed) to tu rn th e bolt s
Fig. 223 C h ang ing a w hee l: alig nme nt pin inside the
top hole
After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.. Use the hexagonal socket in the screwd riv­
er handle
to completely remove the top­
most wheel bol t and set it aside on a
clean
surface ¢ fig. 222 .
What do I do now? 27 7
.. Sc rew the threaded end o f the alignment
pin
from the tool kit hand-tight into the
empty bolt hole
¢ fig. 223 .
.. Then remove the other wheel bolts as de­
scribed above.
.. Take off the wheel leaving the alignment
pin in the bolt hole
¢(D .
Putting on the spare wheel
.. Lift the spare wheel and carefully slide it
over the alignment p in to guide it in place
¢ (]).
.. Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bolts
slightly.
.,. Remove the a lignment pin and insert and
tighten the rema ining wheel bolt slightly
like the rest .
.. Turn the jack hand le counter-clockwise to
lower the vehicle until the jack is fully re­
leased .
.. Use the wheel bolt wrench to tighten all
wheel bolts f irmly
¢ page 2 75. Tighten
them
crosswise, from one bolt to the (ap ­
proximately) opposite one, to keep the
wheel cente red.
CD Note
When removing or installing the wheel,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you.
@ Tips
Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or tighten
the wheel bolts.
- Pull the reversible blade from the screw­
driver before you use the hexagonal
socket in the hand le to turn the wheel
bolts.
- When mount ing tires with
unidirectional
tread design
make sure the tread pat­
tern is pointed the right way
¢page 278.
- The wheel bolts shou ld be clean and easy
to turn. Check for dirt and corrosion on
the mating surfaces of both the wheel

278 What do I do now?
and the hub. R emove a ll dirt from these
su rfaces before remo unt ing the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in
the right direction .
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spa re tire with a t read patte rn
i n te nded fo r use in a specific direction, please
note the fo llowing:
- T he direction o f rotation is marked by a n ar­
row on the side of the tire.
- If the spare t ire has to be in stalled i n the in ­
corre ct d irection, use the sp are tire on ly
temporarily since the t ire will not be a ble to
achieve its optimum perfo rmance character­
ist ics with rega rd t o aquaplaning, noise and
wea r.
- We recommend t hat you pay pa rticular at­
tent ion to this fact during wet weat her and
t h at y ou adjust your speed to matc h road
condit ions .
- Replace the flat tire w ith a new one and
have it installed o n your ve hicle as soon as
poss ible to restore th e handli ng a dvantages
of a un id irect iona l tir e.
Notes on wheel changing
Pl ease re ad the informa tion i:> page 260, New
t ires and repl acing tires and wheels
if you are
goin g to use a spare tire which is differen t
from the tires on your ve hicle.
Afte r you cha nge a tire :
-Check the t ire pressure on the spare imme ­
diately after installation .
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as
possible by your authorized Audi dealer or
a qualified service station .
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lb (120 Nm) . -
If you notice that the wheel bolts are cor­
roded and difficult to turn while changing
a tire , they should be replaced before you
check the tightening torque.
- Replace the flat tire with a new one and
have it installed on your vehicle as soon as
possible. Remount the wheel cover .
Until then , drive with extra care and at re­
duced speeds.
A WARNING
- I f you are going to eq uip your vehicle
wit h tires or rims which differ from those
which were factory installed, then be sur e to r ead the information
i:> page 260,
New tir es and replacing tir es and
wheels.
- Always ma ke sure th e damag ed wh eel o r
e v en a flat tir e and th e jack a nd tool ki t
a re pr operly se cu red in the lugga ge co m­
p art me nt a nd a re not l oo se in the pas­
sen ger com partment .
- I n an a ccide nt or sudde n maneuver they
could fly forward, injuring anyone in the
veh icle.
- Always store dama ged whee l, j ac k and
t oo ls se curely in the l ugg age c omp art­
men t. Otherwise, in an acci dent o r sud ­
de n maneuve r they could fly forwa rd,
causing inj ury to passen gers in the vehi­
cle.

280 Fuses and bulbs
Fuse panel @ (brown)
No. Equipment
1 Headlight control switch
2 Emergency start coil (key
identification)
3 Rear door
control module
(driver's side)
5 Horn
6 Interior lights
(headliner)
Steering column lever, mul-
8
tifunction steering wheel
controls, steering wheel
I heating
10 Power steering column ad-
justment
11 Driver door control module
12 Diagnost
ic connector, light/
rain sensor
14 Power steering column ad-
justment
15 Power
steering, A/C com-
pressor
16 Brake booster
Fuse panel © (black)
No. Equipment
1 Front seat heating
2 Windshield wiper
3 Front exterior lighting
4 Sun roof
5 Driver power window
6 Driver seat (pneumatic)
7 Panoramic
sunroof
8 Dynamic steering
9 Front exterior lighting
10 Windshield/headlight
wash-
er system
11 Rear power window (driver's
side)
Panoramic sunroof
Amps
5
5
7,5 15
7,5
10/5
5
7,5 10
25
20 15
Amps
30
30
30 20
30
7,5
20
35
30
35
30
40
Front passenger side cockpit fuse
assignment
Fig. 227 Front passe nger side cockpit: fuse pane l with
plastic bracket
Fuse panel ® (black)
No. Equipment Amps
1 Anti-theft alarm system
5
2 T
ransmission control mod-
15
ule
3 Front climate control fan 40
4 Engine supply 35
6 Engine
control module
5
7 Front passenger door con-
7,5
trol module
8 Front passenger
power win-
30
dow
9 ESC control module 10
10 E5C control modu le 25
11 Right rear power window
30
12 Front passenger
seat (pneu-
7,5
matics)

2 90 General information
General information Explanation of
technical data
Some of the technical data listed in this man ­
ual requires further explanation .
The technical data for your vehicle is listed in
the charts starting on
r:::> page 292. This sec ·
tion provides general information, notes and restrictions which apply to this data .
Vehicle identification
The key data is given on the vehicle identifica·
tion number (VIN) plate and the vehicle data
sticker.
Fig. 238 Veh icle Ide ntific atio n Number (VlN) p late: lo­
cation on driver 's sid e das h panel
Fig. 239 The vehicle identi fication label -inside the
luggage co mpa rtmen t
The Vehicle Identification Number (VIN)
is located on the driver's side so that it is visi­
b le from the outside through the windshield
r:::> fig . 238. You can also display the Vehicle
Identification Number of your vehicle in the
MMI. Select: Function button
ICAR ! > Car sys­
tems
> VIN number . The
vehicle identification label
is located in the luggage compartment in the
spare wheel wel l.
The label¢
fig. 239 shows the following vehi­
cle data :
(D Production control No .
@ Vehicle identification No.
® Type code number
@ Type designation/engine output in Kilo·
watts
® Engine and transmission code letter
@ Paint No./Interior
(f) Optional equipment No.'s
Vehicle data 2 to 7 are also found in your War·
ranty
& Maintenance booklet.
The safety compliance sticker
is you r assurance that your new vehicle com­
plies with all applicable Federal Motor Vehicle
Safety Standards which were in effect at the
time the vehicle was manufactured . You can
find this sticker on the left door jamb.
It
shows the month and year of production and
the ve hicle ident ification number of your vehi ·
cle (perforation) as well as the Gross Vehicle
Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
The high voltage warning label
is located on the lock carr ier .
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are Listed on a sticker on the
left door jamb.
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank,
oi l and coolant, plus maximum load, wh ich in·
eludes passenger weight (lSO lbs/68 kg per
Ill>

292 Data
Data
AS 3.0
TFSI engine, with all wheel drive
Engine data
Maximum outpu t SA E net
Maximum torque SAE net
N o. of cylinders
Displacement
Stroke
Bore
C ompression ratio hp@rpm
l
b-ft@ rpm
CID (cm
3 )
in (mm)
i n (mm)
333 @ 5500 - 6500
325
@ 2900 - 5300
6 cyli nder
182.7 (2995)
3.51 (89)
3.33 (8 4.5)
10.3: 1
Fuel Premium unleaded (91 AKI)
Recommended for maxi­
mum engine performance. Further details
c:::> page 228,
Gasoline
Dimens ions (approx .)
Length (with license plate bracket) in (mm)
W idth (across mirrors) ____ in (mm)
He ight (unloaded) in (mm)
Turning circle diameter (curb to curb) ft . (m )
Capacities (approx.)
Fuel tank
- Total capacity gal (liters)
- Res erve (of total capacity) gal (lite rs)
Windshield and headlight washer quarts (liters)
fluid container
Engine oil with filter c hang e quarts (lit ers)
Footnotes
c:::> page 291
AS ASL
202.4 (5137) 207.52 (5267) _,, __
83 .1 7 (2 11 1) 83.17 (211 1)
57.52 (1460) 57 .96 (1471)
4 0.3 5 (12 .3) 41.67 (1 2,7 )
23.8 (90 .0)
4 (15)
5 .29 (5)
7.1 9 (6.8)

AS 4.0 TFSI engine., with all wheel drive
Engine data
Maximum output SAE net
Maximum torque SAE net
No . of cylinders
Displacement
Stroke
Bore
Compression ratio hp@rpm
lb-ft@ rpm
CID (cm
3 )
in (mm)
in (mm)
Data
420@5000
444@1500
8 cylinder
243.57 (3993) 3.51 (89)
3 .33 (84.5)
10.1 : 1
Fuel Premium unleaded (91 AKI) Recommended for maxi­
mum engine performance. Further details¢
page 228,
Gasoline
Dimensions (approx .)
Length (with license plate bracket)
Width (across mirrors)
He ight (unloaded) in (mm)
in (mm)
in (mm)
T urning circle diameter (curb to curb) ft . (m)
Capacities (approx.)
Fuel tank
- Total capacity gal (liters)
- Reserve (of total capacity) gal (l iters)
__ _.. __
Windshield and headlight washer quarts (liters)
fluid container
Engine oil with filter change
Footnotes
¢ page 291
quarts (liters)
AS
202.4 (5137)
83.17 (2111)
57 .52 (1460)
-....... -
4 0.35 (12.3)
ASL
207 .52 (5267)
83.17 (211 1)
57 .96 (1471)
41.67 (12,7)
23 .8 (90 .0)
4 (15)
5 .29 (5)
8 .77 (8.3)
293
•
•

294 Data
S8 4.0 TFSI engine, with all wheel drive
Engine data
Maximum output SAE net
Maximum torque SAE net
N o. of cylinders
Displacement
Strok e
Bore
C ompression ratio hp@rpm
l
b-ft@ rpm
CID (cm
3 )
in (mm)
i n (mm)
520@6000
479@ 1700 - 5500
8 cylinder
243 .57 (3993)
3.51 (8 9)
3.33 (84 .5)
9.3 : 1
Fuel Premium unleaded (91 AKI) Recommended for maxi­
mum engine performance. Further details
Q page 228,
Gasoline
Dimensions (approx .)
Leng th (wit h license pl ate brac ket) in (mm)
Width (across mirrors) in (mm)
He igh t (unloaded) in (mm)
T urning circle diamet er (curb to curb) ft. (m)
Capacities (appro x.)
Fuel tank
- Total capacity gal (liters)
- Reserve (o f to tal capacity) gal ( lite rs)
Windshield and headlight washer quarts (liters)
fluid container
Engine oil with filter change quarts (liters)
F oo tnotes
Q page 291
2 02 .2 (51 36)
83.17 (2111) 57.4 (1458)
4 0.35 (12.3)
23.8 (90.0)
4 (15)
5.29 (5)
8. 77 (8 .3)

AS 6.3 FSI engine, with all wheel drive
Engine data Maximum output SAE ne t
M aximum torque SAE net
No . of cylinders
Displacement
Stroke
Bore
Compression ratio hp@r
pm
lb-ft@ rpm
CID (cm
3 )
in (mm)
in (mm)
Data
500@6200
4 63@4750
12 cylin der
384.39 (6299)
3.39 (86.0)
3 .56 (90 .4)
1 1. 8:1
Fuel Premium unleaded (91 AKI) Recommended for maxi­
mu m engine performance. Further details¢
page 228,
Gasoline
Dimension s (approx .)
Length (with license plate bracket)
W idth (across mirro rs)
He ight (unloaded) in (mm)
in (mm)
in (mm)
T urning circle diameter (curb to curb) ft . (m )
Capacities (approx.)
Fuel tank
-Total capacity gal (liters)
- Reserve (of to tal capacity) gal (l ite rs)
Windshield and headlight washer quarts (liters)
fluid container
Engine oil with filter chang e
Footnotes
¢ page 291
quarts (li ters)
ASL
207 .52 (5267)
83.1 7 (211 1)
57 .96 (1471)
4 1.67 (1 2,7)
23 .8 (90 .0)
4 (15 )
5 .29 (5)
12 .16 (1 1.5)
295
•
•

complexity of today's automobi les, have
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Also, safe ty and e nvir onm en tal con­
cerns place very strict limits on the na ture of
repairs and adjustments to engine and trans ­
miss io n pa rts which an owner can perform .
Maintenance, adjustments and repairs usua lly
require special tools, testing devices and oth­
er equipment avai lab le to specially trained
workshop personnel in order to assure prope r
performance, reliab ility and safety of the vehi­
cle and its many systems .
Improper ma intenance, adjustments and re ­
pa irs can impair the operation and reliability
of your vehicle and even void your vehicle war­ ranty. The refo re, p roof of servici ng in accord­
ance w ith the maintenance sched ule may be a
condition for upholding a poss ible war ranty
claim made within the warranty period.
Above all, operational safety can be adversely
affected, crea ting unnecessary risks for you
and your passengers.
If in doubt about any servicing, have it done
by your authorized Audi dealer or any other
properly equipped and q ualified workshop .
We strong ly urge you to give you r a uthorized
Audi dealer the opportunity to perform all
schedu led maintenance and necessary repairs .
Your dea ler has the facilities, or iginal parts
and trained spec ialists to keep your vehicle
running properly.
Performing limit ed m aintenance you rself
The following pages describe a limited num­
ber of procedures which can be performed on
your vehicle with ordinary too ls, should the
need arise and trained personnel be unavaila­
b le. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and carefully follow the instruc­
tions given . Always rigorously obse rve the
WARNINGS provided .
Before you check anything in th e engine
compartment, a lway s re ad and heed all
Con sumer In formation 297
WARNINGS ¢ & and ¢ & in Working in the
engine comportment on page 232 .
A WARNING
-Ser ious personal injury may occur as a re­
sult of improperly performed mainte­ nance, adjustments or repa irs.
-Always be extremely careful when work­
ing on the vehicle. Always follow com­
mon ly accepted safety practices and gen­
eral common sense . Never r isk personal
lnJU ry .
- Do not attempt any of the ma intenance ,
checks or repairs descr ibed on the fol­
lowing pages if you are not fully fam iliar
wit h these or othe r pro cedures with re­
spect to t he veh icle, or are uncerta in how
to p roceed .
- Do not do any work without the proper
too ls and equipment. Have the necessary
work done by your authorized A udi deal ­
er or another proper ly equipped and
qualified workshop .
- The engine compartment o f any motor
veh icle is a potentially hazardous area.
Never reach into the area around or
touch the radiator fan. It is temperature
contro lled and can switch on suddenly -
even when the engine is
off . The radiator
fan switches on automat ically when the
coo lant reaches a certai n temperature
and will cont inue to run until the coo lan t
temper ature drops.
- Always sw itch
off the ignition before any­
one gets under the vehicle.
- Always support your veh icle with safety
stands if it is necessary to work under­
neath the vehicle . The j ack s upplied with
the vehicle is not adequate for this pur­
pose and cou ld collapse causing serio us
personal i njury .
- I f you must work unde rneath the vehicle
with the wheels on the ground, a lways
make sure the vehicle is on leve l ground,
that the wheels are a lways securely
blocked and that the engine cannot be
started.
•
•