battery capacity AUDI S8 2015 Owners Manual

202 Intelligent technology
Driving with your
quattro
With All Wheel Drive, all four wheels are driv­
en .
General inform ation
With All Wheel Drive, power is distributed to
all four wheels . This happens automatically
depending on your driving style and the road
conditions at the time . See also
c:;; page 197.
With the sport differential*, power d istribu­
tion to the rear wheels is variable and can be
adjusted with Audi d rive select*
c:;; page 108.
Always read and follow safety precautions
¢ .&,.
Winter tires
When driving in the winter , your vehicle with
A ll Wheel Drive has an advantage, even with
regular tir es. In winter road conditions it may
be advisable to mount winter tires (or all-sea­
son tires) for improved driveability and brak­ ing: these tires must be mounted on
all four
wheels.
See also ¢ page 260, Winter tires.
Snow chains
Where snow chains are mandatory on certa in
roads, this normally a lso applies to vehicles
with A ll Wheel Drive
c:;, page 261, Snow
chains .
Replacing wheels/tires
Vehicles with All Wheel Dr ive must always
have tires of the same size. Also avoid ti res
with different tread depths. For details see
page
c:;, page 256, New tires and replacing
tires and wheels .
Off-Road driving?
Your Audi does not have enough ground clear­
ance to be used as an off-road vehicle. It is
therefore best to avoid rough tracks and un ­
even terrain as much as possible. Also refer to
c:;; page207.
A WARNING
Always adjust your driving to road and traf­
f ic conditions. Do not let the extra safety
afforded by All Wheel Drive tempt you into
taking extra risks.
- Although the All Wheel Drive is very ef­
fective, always remember that braking
capacity is lim ited by tire traction. You
should therefore not drive at excessive
speeds on icy or slippery road surfaces.
- On wet road surfaces, be careful not to
drive too fast because the front wheels
could begin to slide on top of the water
(aquaplaning) . If this should occur, you
will have no warning from a sudden in­
crease in eng ine speed as with a front­
wheel drive vehicle. Always drive at speeds which are suited to the road con­
ditions - risk of crash .
Energy management
Starting ability is optimized
Energy management controls the distribution
of electrical energy and thus optimizes the
availability of electrical energy for starting
the engine .
If a vehicle with a conventiona l ene rgy system
is not driven for a long period of time, the bat­
tery is discharged by idling current consumers
(e .g. immobilizer). In certain circumstances it
can resu lt in there being insufficient energy
available to start the engine .
Intelligent energy management in your vehi­
cle handles the distribution of e lectrica l ener­
gy. Starting ability is markedly improved and
the life of the battery is extended.
Basically, energy management consists of
battery diagnosis , idling current manage­
ment
and dynamic energy management.
Battery diagnosis
Battery diagnosis continuously determines
the state of the battery. Sensors determine
battery voltage, battery current and battery ..,.

24 0 Ch eck ing and filling
Always check wi th your a uthorized Audi
dealer to make s ure you are using the
correct brake flu id. The correct type of
brake fluid is also indicated on the
brake fluid reservoir.
- The brake fluid must be new. Heavy use
of the brakes can cause a vapor lock if
the brake fluid is left in the system too
long. This can ser ious ly affect the effi­
ciency of the b ra kes as well as yo ur
safety. This could result in an acc ident.
(D Note
Brake flu id will damage the paint of your
veh icle.
@ For the sake of the environment
Because of the problem of proper d isposa l
of brake flu id as wel l as the special tools
requ ired and the necessary expert ise, we
recommend that you have the b rake fluid
changed by your author ized Audi dealer.
Battery
General information
Under
normal operating conditions, the bat­
tery in your Audi does not need any mainte­
n ance . With
high outside temperatures or
l ong daily dr ives we recommend that you have
the elec trolyte level checked by a service fa­
cili ty. The e lec trolyte level sho uld a lso be
checked each time the battery is charged
¢ page 242.
Have the b attery checked when you ta ke yo ur
ve hicl e in for service. Yo u are well adv ise d to
replace a battery that is older than S years .
W ith certa in types of airbag deployment, the
battery is d isconnected from the vehicle ele c­
tr ica l system for sa fety reasons¢
& in Re­
pair, care and disposal of the airbags on
page 165.
Disconnecting the battery terminals
Some veh icle func tions (power w indow regu­
l ato rs, for example) a re los t if the b attery ter- mina
ls are disconnected. These functions have
to be relearned after the battery termina ls are
connected aga in. To prevent th is, the battery
sho uld only be disconnected from the ve hicle
electrical system when abso lutely necessary
for repairs.
Vehicle s not driven for long peri ods
If you do not d rive your vehicle over a period
of several days or weeks, e lectr ica l compo ­
nents are gradually cut back or sw itched off.
This reduces energy consumption and ma in­
ta ins start ing capability over a longer period
¢
page 202. Some of the convenience func­
t ions may not ope rate, such as the inter ior
li gh ts or the power seat adjus tment. The con­
venience func tions will be ava ilable ag ain
when you switch on the ignition and start the
engine .
Winter operation D uring the winte r months, battery capac ity
tends to de crease as temperatures drop. This
is beca use more power is also consumed wh ile
sta rting, and the headlights, rear window de ­
fogger, etc ., are used more often .
Avoid unnecessary power consumpt ion, p ar­
t icu lar ly in city traffic or whe n traveling only
short distances. Let yo ur au thorized Aud i
dealer check the capacity of the vehicle bat ­
tery before winter sets in ¢
page 242. A well
charged battery will not on ly prevent starting
problems when the weather is cold, but will
also last longer.
(!) Tips
If your vehicle is left standing for several
weeks at extremely low temperatures, the
vehicle battery sho uld be removed and
stored where it w ill not freeze. This will
prevent it from be ing damaged and having
to be repla ced.

.... N .... N
0 J:
'SI: .... \!) 1.1"1
.... 1.1"1 ,....,
Fa st charging the b att ery (charging rate
abo ve 14.8 Vo lt s)
Fo r technical reasons do not use a batt ery
charger that uses vo ltage g reater than 14.8
Volts to charge your vehicle's battery.
A WARNING
-
Charging a battery can be dangerous.
- Always follow the operating instructions
provided by the battery charger manu­
facturer when charging your battery.
- Never charge a fro zen battery. It may ex­
plode because of gas trapped in the ice.
Allow a frozen battery to thaw out first .
- Do not reuse batteries which were fro­
zen. The battery housing may have
cracked and weakened when the battery
froze .
- Charge the battery in a well ventilated
area . Keep away from open flame or elec­
trical spark . Do not smoke . Hydrogen gas
gene rated by the battery is exp losive.
- To reduce the danger of explosion , never
co nnect or disconnect cha rger cables
wh ile the charger is operating.
- Fast charg ing a battery is dangerous and
should only be attempted by a compe­
t ent technicia n w ith the proper eq uip­
ment.
- Battery a cid that may spill d uring charg­
ing should be washed off wit h a solution
of warm wa ter and ba king soda to neu ­
tralize the acid .
CD Note
Never use a fast charge r as a booster to
s tart the engine. This will se rio usly d am­
age sensitive elect ronic components, such
as control units, relays, radio, etc., as we ll
as the battery charger .
Checking and fillin g
Battery replacement
The new battery must have the same specifi­
cations and dimensions as the original equip­
ment battery.
In telligen t energy managemen t in your vehi­
cle is responsible for distributing the electri ­
cal ene rgy throughout your vehicle
¢ page 202. The intelligent energy manage­
ment system will keep the engine battery
c h arged better than vehicles without this sys ­
tem. To make sure the additional electrica l en ­
ergy is avai lab le once again afte r yo u have
changed the battery, we recommend that you
insta ll batteries of the same type and m anu­
facture only (the same as those installed at
the time your ve hicle was delivered) . Specif i­
cat ions are listed on the battery housing . Your
authorized dea le r must code the battery in
the energy management system to enab le you
to use the ene rgy manageme nt func tions cor ­
re ct ly afte r replacing the battery.
The new battery must have the same capacity,
vo ltage
( 1 2 volts), amperage, const ruction
and plug seal ing .
When installing the battery, make sure the ig­ nition and a ll elect rical consume rs are switch­
ed off .
CD Note
- Make sure the ventilation hose on the
side of the battery is connected, other­
w ise fumes or battery a cid ca n leak out .
- Veh icles with the Start-Stop-System* are
e quipped with a spec ial cycle-p roof AGM
battery. Install ing a d iffe rent type of
ba ttery c an cause problems in the vehi ­
cle e lectrical system. Whe n replacing the
vehicle battery, always install one w ith
the same specifications as the origina l
battery.
- Battery mounts and clamps must a lways
be sec ured correct ly .
- Read and fo llow the wa rnings under
¢ page 241, Working on the battery be-
fore per forming any work on the battery . ..,_
243
•
•

244 Checking and filling
@ For the sake of the environment
Because of the problem of proper disposa l
of a battery, we recommend your author­
ized Audi dealer change the battery for
you. Batter ies contain sulfuric acid and
lead and must always be disposed of prop­
erly in compliance w ith all environmental
regu lations . D isposing of vehicle batteries
improperly is very dangerous to the envi­ ronmen t.
Windshield/headlight
washer container
Fig. 207 Engine compartment: cover on the windshield
was her flui d reservo ir
The washer fluid container is marked with the
symbol~ on its cap
c::> fig. 207, c::> page 230 .
.. Before you check anyth ing in the engine
compartment,
always read and heed all
WARNINGS c::> A in Working in the engine
compartment on page 228 .
.. lift the filler cap tongue to add washer flu­
id . You can fill the container to the top .
.. Press the cap back onto the filler neck after
filling the container.
You can find the reservoir
capacity in the table
in
c::>page 288.
Clean water should be used when filling up. If
possible, use soft water to prevent scaling on
washer jets. Always add a glass cleaner solu­
tion (with frost protection in the winter).
(D Note
Do not mix engine coolant antifreeze or
any other additives to fill up the wind­
shield washer reservoir.

,....,
N ,....,
N
0 J:
'SI: ,...., \!) 1.1"1 ,...., 1.1"1 ,....,
Tires and wheels 24 7
Gross Vehicle Weight Rating ("GVWR") Ply
means the maximum total loaded weight of
the vehicle .
Groove
means the space between two adjacent tread
ri bs.
Load rating (code)
means the maximum load that a tire is rated
to carry for a given inflat ion pressure . You
may not find this informat ion on all tires be­
cause it is not requ ired by law.
Maximum load rating
means the load rating for a t ire at the max i­
mum permissible inflation pressure for that
tire .
Maximum loaded vehicle weight
means the sum of:
(a) Curb weight
(b) Accesso ry weight
(c) Vehicle capacity weight, and
(d) Production opt ions we ight
Maximum (permissible) inflation pressure
means the maximum co ld inf lation pressure
to which a tire may be inflated . Also called
"maximum inflation press ure."
Normal occupant weight
means 150 lbs . (68 kilograms) times the
number of occupants seated in the vehicle up
to the tota l seating capacity of your vehicle.
Occupant distribution
means distribution of occupants in a veh icle.
Outer diameter
means the overall diameter of an inflated new
tire .
Overall width
means the linear distance between the exteri­
ors of the sidewalls of an inflated tire, includ­
ing e levations due to labeling, decorations, or
protective bands or ribs. means a layer of
rubber-coated parallel cords.
Production options weight
means the combined weight of those installed
regular production opt ions we ighing over 5
lbs. (2.3 kg) in excess of those standa rd items
which they replace, not previously considered
in curb weight or accessory weight, including
heavy duty brakes, ride levelers, roof rack,
heavy duty battery, and spec ial trim.
Radial ply tire
means a pneumatic tire in which the ply cords
that extend to the beads are laid at substan­
tially 90 degrees to the centerline of the
tread.
Recommended inflation pressure
see ~ page 246, Cold tire inflation pressure .
Reinforced tire
means a tire design to operate at higher loads
and at higher inflation pressures than t he cor­
responding standard tire. Reinforced tires
may be identified as "XL", "xl", "EXTRA LOAD",
or "RF" on the sidewal l.
Rim
means a metal support for a tire or a t ire and
tube assembly upo n which the tire beads are
seated .
Rim diamete r
means nominal diameter of the bead seat. If
you change your wheel s ize, you wi ll have to
purchase new tires to match the new r im di­
ameter .
Rim size designation
means rim diameter and width.
Rim width
means nominal distance between rim flanges.
Sidewall
means that portion of a t ire between the
tread and bead .
•
•

.... N .... N
0 J:
'SI: .... \!) ..,.,
.... ..,., ,....,
Emergency situations
General
This chapter i s intended for trained emer­
gency crews and working personnel who have the necessary tools and equipment to
perform these operations.
Starting by pushing or
towing
(D Note
Ve hicles w ith an au tomatic tra nsmission
cannot be started by pus hing o r tow ing.
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine shou ld fail to start because of a
discha rged o r wea k battery, the battery can be
connected to the battery o f
another vehicle,
using a
pair of jumper cables to start the en­
g ine.
Jumper cables
Use only jumper cables of sufficiently la rge
c ross section to carry the starter c urrent safe­
l y. Refer to the man ufacturer's specifications.
Use only jumper cables with
insulated te rm i­
na l clamps wh ic h are d istinctly marked:
plus(+) cable i n mos t cases co lore d red
minu s(-) cable
in most cases colored black .
A WARNING
Batterie s contain e lec tricity, ac id, an d gas.
A ny of these can cause ve ry ser io us or fatal
inju ry. Follow the instructions below f or
safe han dling of your veh icle's b attery .
- Alway s shield you r eyes and avoid lean­
ing over the bat te ry whenever possib le.
- A dis ch arged battery c an free ze at tem­
peratures ju st be low 32 °F ( 0 °C ). Befo re
Emergency situations 281
connecting a jumpe r cab le, you must
thaw the fr ozen battery c omp lete ly, ot h­
erwise it could explode.
- Do not allow battery acid to contact eyes
or skin. Fl ush any contacted area with
wate r immediately.
- Improper use of a booster battery to start a vehicle may cause an explosion.
- Vehicle batter ies genera te exp losive gas­
es. Keep spar ks, flame and lighted c iga ­
rettes away from batte ries.
- Do not try to jump start any ve hicle w ith
a low ac id leve l in the battery.
- The vo ltage of the booste r batte ry m ust
a lso have a 12-Vol t rating. T he capacity
(Ah) of the booster battery sho uld not be
lowe r tha n that of the discharged bat­
tery . Use of batte rie s of d iffe ren t voltage
or substantially diffe rent "Ah" rat ing
may c au se an exp losion and persona l in­
JU ry.
- N ever cha rge a fro zen battery. Gas trap­
pe d in the ice may cause a n ex plosion.
- Never cha rge or use a batte ry tha t h as
been fr ozen. T he battery case may have
be weakened.
- Us e of b atter ies of differe nt voltage or
sub stant ia lly diffe ren t ca pa city (Ah) ra t­
i ng may c ause an ex plosion an d injury .
Th e capac ity (Ah) of the booster bat tery
should not be lower than that of the dis ­
charged batte ry .
- Before you chec k any thing in the engine
compa rtment, always read and hee d all
WARNINGS¢
page 22 8.
(D Note
- App lyin g a higher vo ltage booster ba t­
t ery w ill cause expens ive damage to se n­
sit ive e lectronic com ponents, such as
cont ro l units, relays, rad io, etc.
- The re must be no electrical contact be­
tween the vehicles as ot herwise c urrent
co uld a lready start to f low as soon as the
p o sit ive(+) term inals a re connected. ..,. •
•