air condition AUDI TT 1995 8N / 1.G ATW Engine Oxygen Sensor Control Workshop Manual

24-73


Display fields

1 2 3 4
Display group 030: Oxygen sensor status
Display
X X X X X X

Indicated
Oxygen sensor status, bank 1, sensor 1 Oxygen sensor status, bank 2, sensor 1

Functional
range 0 = off
1 = on 0 = off
1 = on

Specified
value 1 1 1 1 1 0

Note
If specified value is not obtained Page 24
-80

If specified value is obtained but there is a malfunction stored in DTC memory Check oxygen
sensor adaptation values and control, Page 24
-74

Significance of 3 digit indications in display group 030 X
X
X
Display fields 1 and 2
X Oxygen sensor control: 0= not active; 1 = active
X Operational readiness of oxygen sensor: 0= not active; 1 = active
X Condition of oxygen sensor heater: 0= not active; 1 = active
Note:
The first field of the 3 digit indication (heating) fluctuates between 0 and 1.
Pa
ge 3 of 37 Ox
yg
en sensor control, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.2

24-85


Display fields

1 2 3 4
Display group 034: Diagnostic oxygen sensor aging
Display xxxx/min
xxx C
x.x s
---
Indicated Engine speed
(RPM) Exhaust
temperature Period duration Oxygen sensor before
Catalytic converter Diagnostic
condition
Functional
range

Test OFF
Test ON
B1-S2 OK
B1-S2 not OK
Specified
value 1800 to 2200
RPM more than 350 C
0.0 to 1.0 s B1-S2 OK
Note


If specified value is not obtained Continuation, Page 24
-
86

Note for display field 2:
Calculated value from engine speed and engine load.
Note for display fields 3 and 4:
Period duration is the time between two oxygen sensor voltage jumps (e.g. rich - lean - rich) and is therefore a measurement
of the aging condition of the oxygen sensor. If the specified time is exceeded, display field 4 will indicate = B1-S1 not OK.
Pa
ge 15 of 37 Ox
yg
en sensor control, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.2

24-91


Display fields

1 2 3 4
Display group 030: Oxygen sensor status with engine at idle
Display X X X
X X X

Indicated Oxygen sensor status, bank 1, sensor 1
Oxygen sensor status Bank 2, sensor 1

Functional range 0 = off
1 = on 0 = off
1 = on

Specified value 1 1 1
1 1 0

Note
If specified value is not obtained Page 24
-99

Significance of 3 digit indications in display group 030 X
X
X
Display fields 1 and 2
X Oxygen sensor control: 0= not active; 1 = active
X Operational readiness of oxygen sensor: 0= not active; 1 = active
X Condition of oxygen sensor heater: 0= not active; 1 = active
Note:

Oxygen sensor control of oxygen sensor behind catalytic converter (B1-S2) is not active without engine load.
The first position of the 3 digit indication (heating) fluctuates between 0 and 1.
Pa
ge 21 of 37 Ox
yg
en sensor control, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.2

24-93


Display fields

1 2 3 4
Display group 037: Diagnostic oxygen sensor control system
Display xxx %
x.xxx volts
xxx ms
---
Indicated Engine
load Oxygen sensor voltage
Bank 2, sensor 1 Dwell time, oxygen sensor control
before catalytic converter, bank 1 Diagnostic condition
Functional
range


Test OFF
Test ON
System OK
System not OK
Specified
value 15 to 33
% 0.100 to 0.900 V
-150 to 150 ms System OK
Note

If specified value is not
obtained: Evaluation display
field 2 Page 24
-94

If value climbs to above 300 ms,
this indicates a leaking exhaust
system or faulty oxygen sensor If "SYST not OK" is
displayed: Check DTC
memory Page 01
-16

Note for display field 3:
Oxygen sensor control behind catalytic converter is superior to oxygen sensor control before catalytic converter and is
responsible for control correction. It corrects slight changes in the mixture (i.e. toward rich or lean) due to the oxygen sensor
before catalytic converter by holding oxygen sensor control before catalytic converter at its higher or lower point for a specific
time (dwell time). If this time is in the positive range (i.e. 50 ms), mixture is shifted in the -enrich- direction. If this time is in the
negative range (i.e. -50 ms), mixture is shifted in the -lean- direction.
Pa
ge 23 of 37 Ox
yg
en sensor control, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.2