set AUDI TT 2004 8N / 1.G RNS_E Navigation System Manual

Navigation (NAV)135
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
–Select Top categories
page 134, fig.140. You are given
a list of suggestions with categories for useful special
destinations.
– Select the desired category (e.g. Gas station. You are
provided with a list containing the special destinations
from the selected category.
– Select a destination from the list.
–Select Set as destination. Die Zieldaten werden automa-
tisch in das Zieleingabemenü übernommen.
–Select Start route guidance.The special destinations are sorted according to distance from your
present location.
The following top categories are available:

Parking lot


Parking garage


Gas station


Audi service


HospitalTips
If no top special destination is found for the category selected, there
is no top special destination from this category in your vicinity or no
top special destination from this category exists on the navigation
DVD.
Store in directory
The current destination can be stored in the directory.Fig. 142 Navigation: Save current destination to directory– Enter a single destination
page 119.
–Press the Memory control button.
– Select Store in directory.
– Select New directory entry and complete the directory
card, or
– Select Find entry, to file the destination under an existing
directory card.

Navigation (NAV)137
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Tips
Administration of the directory data is handled through the
button
page 98.
Save route
Once calculated, route plans can be saved with the
route criteria you entered and loaded later as a new
destination.Fig. 144 Navigation: Route plan– Enter a route plan
fig.144.
–Press the Memory co n t ro l bu t to n i n t h e n a vi g a t i o n m e n u .
–Select Save route.– Using the speller, enter the name for the route.
– Select OK in the speller. The route plan entered is saved.
A route plan provides the option of setting up to three stopovers in
addition to a destination
page 121. You can then drive to each of
these destinations in turn in the sequence set up.
The route entered will be saved with the final destination and stop-
overs and can be loaded again as a new destination
page 137.
The route plan can be changed at any time after input is complete.
Select a destination from the route plan by rotating and pressing
the control knob. Then you can select Change, Move, Delete o r Drive
to now
page 137.
If you have selected the Drive to now function and you would not
l i k e t o e d i t t h e r o u t e , r o u t e g u i d a n c e i s i m p o r t e d a n d c u r r e n t v e h i c l e
location is used as the route guidance starting point after you have
selected Start route guidance.
If the Save route f u n c t i o n i s g r e y e d o u t , t h i s i n d i c a t e s t h a t e i t h e r t h e
route memory is full or the Route without stopover function (single
destination mode) is set. Please delete routes not needed from the
route memory
page 138. Or select the Route with stopover func-
tion
page 139Tips
You can save individual destinations to the directory
page 135.
Load route–Press the Memory c o n t r o l b ut to n i n t h e n a v i g a t i o n m e n u .
NAME

Navigation (NAV) 138
– Select Load route
page 134, fig.140.
– Select the route that you would like to load from the list.
– Select Start route guidance.After storing several route plans
page 137, they can be loaded
with a few operating steps.
A route plan can be changed at any time. Select a destination from
the route plan by rotating and pressing the control knob. Then you
can select Change, Move, Delete or Drive to now.
Change
Here you are entering new navigation data for your destination or
stopover.
Move
Here you are reordering the sequence of your destination and stop-
overs.
Delete
The selected destination or stopover can be deleted. If you delete a
destination, the system will automatically select a stopover and
make that your new destination.
Drive to now
You can drive directly to the selected final destination or stopover.
If you do not want to ed it the saved route, the route will b e sa ved in
the memory when Start route guidance is activated and the current
vehicle location will be used as the starting point for navigation.
Tips
A function may not be selected (“greyed-out”) if it is not available
according to the restrictions you have set, or if not permitted by
local circumstances.Delete route–Press the Memory control button in the navigation menu.
– Select Delete route.
– Select the route to be deleted from the list.
–Confirm Are you sure you want to delete the route? with
Ye s. The selected route is deleted.

Navigation (NAV)139
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Route control buttonRoute with/without stopoverFig. 145 Navigation: Route with stopoverFig. 146 Navigation: Route plan
Only the type of route guidance which is not active at the
time is shown in the display as available.
–Press the Route control button in the navigation menu.
– If you would like to visit stopovers on the way to your
final destination, select Route with stopover
fig.146
and enter your driving route with stopover and destina-
tion addresses into the Route plan
page 121.
– If you want the Navigation System to take you to your
final destination without stopovers, select Route without
stopover and enter the address of your destination

page 119.The system operates with the type of route guidance you selected
until it is changed. For example, if you have selected Route with

Navigation (NAV)141
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Route criteria
Route calculation depends on the route criteria
selected.Fig. 148 Navigation: Listing of the possible route criteria–Press the Route control button in the navigation menu.
–Select Route criteria.
– Select the desired route criteria
fig.148.The route criteria can be changed during route guidance and the
route can be recalculated.
You have the following route criteria available to you:
Route options
Using the options fast or short, an especially fast or short route is
taken as the basis for calculating the route.Highway
Comprises the options include and minimize. With Highway
minimize, an attempt is made to avoid sections of freeway when
calculating the route. If the destination is more than 300 km away,
freeways are not avoided.
Ferry
Comprises the options include and minimize. With Ferry minimize
a n a t t e mp t i s m a d e n o t to i n c l u d e a ny s t re t ch w hi ch i n c l ud e s a fe rr y
connection when calculating the route.
To l l r o a d
Comprises the options include and minimize. With To l l r o a d
minimize an attempt is made when calculating the route not to
include any stretch which includes a road which you have to pay to
drive on.
Time restrict.
Comprises the options include and minimize. With roads closed at
certain times of day avoid a n a t t e m p t i s m a d e t o e x c l u d e t h e s e r o a d s
when planning the route. But only the roads closed at certain times
of day identified on the Navigation DVD can be avoided.
Season restrict.
Comprises the options include and minimize. With seasonally
closed roads avoid a n a t t e m p t i s ma d e to e x c l u d e t h e s e ro a d s w h e n
planning the route. But only the seasonally closed roads identified
on the Navigation DVD can be avoided.
Tips
If you would like to avoid a route criterion, but this makes route
guidance impossible, this criterion is still included when calculating
the route. In this case, a voice message will inform you of this.

Navigation (NAV) 142Av o id ro u t eYou can select this function once calculated route guidance
is active.
–Press the Route control button in the navigation menu.
– Select Avoid route from here
page 139, fig.145.
– By rotating and pressing the control knob, select the
section on the presently calculated route from the
vehicle position.
– By pressing the control knob, you confirm the section
you wish to avoid.The Navigation System will calculate an alternative route for the
section of the route you wish to avoid.
If you stop route guidance and restart it, the blocked out section
entered is cancelled and has to be reset if required.
Tips


If the Avoid route from here fun ction is greyed out or the Na vig a-
tion System does not calculate an alternate route, local conditions
are making this impossible.


If the recommended detour route is not followed, the system
automatically calculates a new route from the current position
without given further consideration to the previously closed
section.
Map control buttonGeneral
There are various displays for maps and information
with different options possible.Fig. 149 Navigation: Map display with an IPD areaPossible map displays are:

Map and information display during route guidance with inac-
tive side menu
page 143.


Map display with active side menu
page 144
If light grey lines
fig.149 are shown on the map display, this
means that IPD sections/areas are being shown. IPD means “in-
progress-data”, i.e data collection is incomplete and consequently
they cannot be included for route guidance. These IPD
sections/areas are on the Navigation DVD and are represented on

Navigation (NAV)143
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP the map by light grey lines
f i g .1 4 9 . Th e r e i s n o r o u t e g u i d a n c e f o r
IPD sections, instead you are guided by directional arrows
fig.149. These directional arrows point in the compass direc-
tion/a direct line to the destination.
I f y o u s h o u l d b e s t a r t i n g y o u r r o u t e g u i d a n c e i n a n I P D a r e a , y o u w i l l
initially be guided by directional arrows. As soon as you leave the
IPD area, route guidance will start . In
page 142, fig.149 an
example is shown of a directional arrow in an IPD area.
If your destination should lie in an IPD area, the Navigation System
will guid e you up to the star t of the IPD area. In the IPD area you will
be guided by directional arrows.
If your route guidance includes an IPD area, you will be advised of
this by a voice message when route guidance starts (“It is possible
that there a re un fore seen tra ffic reg ulations on the way to the des ti-
nation.”).
Tips
Route guidance is additionally shown by directional arrows in the
instrument cluster display
page 113 or
page 114. In an IPD
area, the directional arrows in the instrument cluster display point
in the compass direction/a direct line to the destination.
Map and information displayFig. 150 Navigation: Example of map display with inactive side menu
Fig. 151 Navigation: Example of map display with activated turn list
A
A1

Navigation (NAV) 144Th e fi g ure s
page 143, fig.15 0 a nd
page 143, fig.151 show you
the possible types of information in the map display:
Map orientation
Scale
Estimated distance to the next destination/stopover
Estimated time of arrival to the next destination/stopover
Ve hicle s ymbol
Example of selected map contents page 155
Turn list inserted in the Setup menu page 156
The map display modes can be changed page 151.
A crosshair with selection rectangle helps you select your destina-
tion with the aid of the map
page 148.
Route guidance is additionally shown by directional arrows in the
instrument cluster display (
page 113 or
page 114).
Tips
An underpass or a tunnel is shown by broken lines on the map
display up to a scale of 0.5 mile.
Map display with active side menu
The map display can be changed through the active
side menu.Fig. 152 Navigation: Map display with active side menu–Press the Map control button in the navigation menu.
– Press the control knob to switch to the side menu

fig.152.
– Select the desired submenu item by rotating and
pressing the control knob and make your changes.
– Press the button, to leave the map side menu.If you have activated the Zoom function
page 146 or the
crosshairs
page 149 in the active side menu, you have to press
the button twice in order to leave the map side menu.
A1AA AA4A9A:
RETURN
RETURN

Navigation (NAV)145
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP After you have activated the side menu, you are shown information
(city/street names and longitude/latitude) for the position you had
reached at the time of activation.
The following functions can be carried out using the
active map side menu:
Tips
Settings made in an active side menu are not kept after deactiva-
tion. You can enter permanent settings for the map display using
Setup Navigation
page 151.
Map orientation
Inside side menu activation you can switch back and
forth between direction of travel and North.Fig. 153 Navigation: Map orientation North in the active side menu–Press the Map control button in the navigation menu.
– Press the control knob to switch to the side menu.
– Rotate the control knob to the first map menu item

fig.153.
– By pressing the control knob, you can switch back and
forth between orientation North
fig.153 and Tr a v e l.
For the time the side menu is active, the changed setting
remains.
Legende
FunctionOrientation page 145Scale page 146Map position menu page 148Activation of map crosshairs page 149Presentation of map crosshairs page 149Vehicle symbol
A1AA AA4A9
A1

Navigation (NAV) 146
–Press the button
page 18, to leave the map
side menu.When you change the map orientation with the side menu active,
this map orientation remains only for the time the side menu is
active. After the map side menu is deactivated, the orientation
entered in Setup becomes active again
page 153.
When you make the selection North, the map is oriented to the
North
page 145, fig.153. The vehicle always remains in the center
of the display.
When you make the selection Drive, the vehicle symbol is oriented
pointing upward. The map rotates around the vehicle.
An active map side menu is deactivated again by pressing the
button
page 144.
Zoom mapFig. 154 Navigation: Adjusting zoom with inactive side menu
Fig. 155 Navigation: Adjusting zoom in active side menu
RETURN
RETURN