high AUDI TT 2005 8N / 1.G RNS_E Navigation System Manual

Adjusting sound settings95
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Tips
If the volume is too high when the radio is turned on, it will be
reduced automatically to a level set at the factory. If the volume is
too low when the radio is turned on, it will be increased automati-
cally to a level set at the factory.

Navigation (NAV)109
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Tips


The Navigation System is designed to provide you with
suggested routes in locating addresses, destinations and other
points of interest.


Changes in street names, construction zones, traffic flow, points
of interest or other road system changes are beyond the control of
Audi of America, Inc.


Complete, detailed mapping of lanes, roads, streets, toll roads,
highways, etc., is not possible, therefore you may encounter
discrepancies between the mapping and your actual location.
IntroductionGeneralFig. 112 Display: Example of navigation mapThe Audi Navigation System can help you to reach your destination
without spending a lot of time studying maps.
During the trip you will receive information on vehicle location,
in structions for turning (directio n and dis tance to turn-off), p resen t
distance to destination and estimated time of arrival at destination
in the Navigation System display
fig.112 and in the instrument
cluster display
page 111, fig.114. In addition you will receive
navigation prompts in the form of a spoken announcement
page 112.
There are two possibilities for guide destination:

Route without stopover (Single destination mode)

Navigation (NAV)113
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP map
page 143 and in Setup Navigation
page 151 to d i s p l a y th e
map.
If you are navigating without stopovers, you have the option of
selecting from up to three routes, in addition to detailed route infor-
mation
page 130.
If you are n avigatin g with stopovers, you are shown the entire route
with all stopovers and detailed information in an overview
page 132.
You can also use the map as presented in the Navigation System
display to enter a destination
page 128.
Applies to vehicles: with display of the instrument clusterVisual presentation in the instrument cluster display
A s s o o n a s y o u h a v e e n t e r e d a r o u t e i n t o t h e N a v i g a t i o n S y s t e m a n d
begun navigating, guidance to your destination will also be
displayed in the instrument cluster display.
Fig. 116 Instrument
cluster display:
Example of route guid-
ance presentation
Display
Shor t descriptionEstimated time of arrival at destination or current
stopoverDistance remaining to next turn pointDirectional arrowLocation-dependent display of freeway, highway
and street names
An arrow before the display identifies the name of
the street onto which you should turn.Total kilometers to destination or current stopover
Fig. 117 Instrument
cluster display:
Example of route guid-
ance presentation
(turn off)
A1A2A3A4A5

Navigation (NAV)115
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP A s s o o n as y o u h a v e e n t e r e d a r o u t e i n t o t h e N a v i g a t i o n S y s t e m a n d
begun navigating, guidance to your destination will also be
displayed in the instrument cluster display.
When the turn-off is immediately ahead, the arrow points in the
direction in which you should turn. In addition, the name of the
s t r e e t i s s h o w n u n d e r t h e a r r o w. A b a r g r a p h
page 114, fig.119 on
the right in the display takes you precisely to the turn-off point.If it is necessary to make a lane change before the turn off, you are
warned in plenty of time about this lane change before the turn-off
arrow by a second arrow
page 111, fig.114.
Tips
With active guidance, you can switch to the trip computer display*
by pressing the trip computer reset button*. Pushing the trip
c o mp ut e r re s e t b ut to n * a g a in r e t ur n s y o u to g u i d a n c e . Yo u c a n fin d
detailed information about the trip computer* in the Owner's
Manual.Selecting navigation function
The navigation functions can be selected with the
function button.Fig. 120 Display: Main navigation menu
Display
Short descriptionDistance remaining to next turn pointEstimated time of arrival at destination or current
stopoverDirectional arrowLocation-dependent display of freeway, highway
and street names
An arrow before the display identifies the name of
the street onto which you should turn.Total kilometers to destination or current stopoverChange of direction arrowBar graph (countdown): bars decreasing in size indi-
cate how the distance to the immediate turn-off
point is decreasing; the bar graph is not shown until
a change of direction arrow is displayed.If there is another side street before the turn-off
point which is not part of current guidance, this side
street is represented by a side-street symbol in the
instrument cluster display.
A1AA AA4A9A:A
NAV

Navigation (NAV)117
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP The following submenus are available in navigation
Setup function:
Main navigation menuEntering a navigation destination
Destinations can be easily entered in various ways.Fig. 121 Navigation: Destination entry menu (main menu)First determined whether you would like to navigate to a final desti-
nation with or without stopovers
page 139. After you have
decided on the type of guidance (with/without stopovers), you can
enter a destination over different routes. Entering destination data
in the entry menu
fig.121 is handled in the same way in single
destination and route planning mode.
Navigation submenus
Press the
function button in
the NAV function page 151
Map scheme (day/night)
Orientation
Map type
Map contents
Voice information
Delete previous destinations
Turn list
Highway info
Intersection map
Auto intersection zoom
Compass
Version information
Demo mode
Set position/direction
SETUP

Navigation (NAV)131
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
– Press the control knob to start the route guidance
desired.When you select a route by rotating the control knob, you are shown
various information about this route. The information that pertains
to the selected route is highlighted in white.
The following information can be displayed for the individual
routes.
Route guidance includes sections of freeway
Estimated freeway kilometers
Route includes sections of road subject to tolls or sticker
showing the length of the sections
Route includes ferry connection(s)
Route includes roads closed at certain times of day
Route includes seasonally closed roads
Estimated distance to destination
Estimated time of arrival at destination
Destination highlighted on map
Suggested route 1
Suggested route 2
Suggested route 3
Starting point highlighted
Orientation
Scale
When you have entered a single destination and started route guid-
ance, the system switches automatically to route selection display.
The route highlighted after the automatic switch to map display is
the route which was calculated according to the criteria
page 141
that you set. For e x ample, if you set “fast in the “Route criteria”, the
route with the shortest estimated arrival time is highlighted after switching automatically to the map display. You are also offered a
second fastest and a short route as a selection where possible.”
If you do not select any of the routes suggested, the route marked
is automatically imported after a delay once the trip has started or
during the trip. The delay gives you the opportunity to change the
route selection one more time.
Tips
The estimated time for the possible routes depends on the various
route options. As soon as the calculation is complete, these routes
are shown on the map display. In some cases, visual overlaps may
result, in which c ase the route ca n be distinguished vis ually on ly by
the change in the distance given or the estimated time of arrival.
A1AA3A4A5A6A7A8A9A10A11A12A13A14A15

Navigation (NAV) 132Route plan information before starting Route guidanceFig. 137 Navigation: Example of route plan map overview– Press the control knob to start the route guidance
desired with the stopovers you set.If you are navigating with stopovers, no alternate routes are calcu-
lated. The calculated route shown matches the route criteria
selected
page 141.
The following information can be found on the map display before
starting the route.
Route guidance includes sections of freeway
Estimated freeway kilometers
Route includes sections of road subject to tolls or sticker
showing the length of the sections
Route includes sections with a ferryRoute includes seasonally closed roads
Route includes roads closed at certain times of day
Estimated distance to destination
Estimated time of arrival at destination
Starting point highlighted
Highlighted stopover 1 on the map
Highlighted stopover 2 on the map
Highlighted stopover 3 on the map
Final destination highlighted on map
Orientation
Scale
Changing/Interrupting route guidance– Press the function button or press the
button.
– Select Stop route guidance.
– Change the information if necessary.
– Select Start route guidance.When route guidance is cancelled, the data and settings that have
already been entered are saved. This allows you, for example, to
change the route criteria
page 141 and to recalculate the route.
If you do not complete route guidance you started, this route guid-
ance will be contin ued the ne xt time the ve hicle is star ted . This also
applies to destinations entered which cannot be reached because of
local conditions (e.g. lake or tourist attraction). If you would like to
A1AA A
A4A9A:AA A;;A;A; A;A;4
NAV
RETURN

Navigation (NAV)141
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Route criteria
Route calculation depends on the route criteria
selected.Fig. 148 Navigation: Listing of the possible route criteria–Press the Route control button in the navigation menu.
–Select Route criteria.
– Select the desired route criteria
fig.148.The route criteria can be changed during route guidance and the
route can be recalculated.
You have the following route criteria available to you:
Route options
Using the options fast or short, an especially fast or short route is
taken as the basis for calculating the route.Highway
Comprises the options include and minimize. With Highway
minimize, an attempt is made to avoid sections of freeway when
calculating the route. If the destination is more than 300 km away,
freeways are not avoided.
Ferry
Comprises the options include and minimize. With Ferry minimize
a n a t t e mp t i s m a d e n o t to i n c l u d e a ny s t re t ch w hi ch i n c l ud e s a fe rr y
connection when calculating the route.
To l l r o a d
Comprises the options include and minimize. With To l l r o a d
minimize an attempt is made when calculating the route not to
include any stretch which includes a road which you have to pay to
drive on.
Time restrict.
Comprises the options include and minimize. With roads closed at
certain times of day avoid a n a t t e m p t i s m a d e t o e x c l u d e t h e s e r o a d s
when planning the route. But only the roads closed at certain times
of day identified on the Navigation DVD can be avoided.
Season restrict.
Comprises the options include and minimize. With seasonally
closed roads avoid a n a t t e m p t i s ma d e to e x c l u d e t h e s e ro a d s w h e n
planning the route. But only the seasonally closed roads identified
on the Navigation DVD can be avoided.
Tips
If you would like to avoid a route criterion, but this makes route
guidance impossible, this criterion is still included when calculating
the route. In this case, a voice message will inform you of this.

Navigation (NAV)147
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Changing scale with inactive side menu:
–Press the Map control button in the navigation menu.
– Rotate the control knob counterclockwise to zoom into
the map (smaller scale, display of details), or
– Rotate the control knob clockwise, to zoom out of the
map (larger scale, more overview). You are shown the
scale
page 146, fig.154 in the side menu.
Changing scale with inactive side menu:
–Press the Map control button in the navigation menu.
– Press the control knob to switch to the side menu.
– Rotate the control knob to the second menu item.
– Press the control knob to activate the map menu item
Zoom (white highlight)
page 146, fig.155.
– Rotate the control knob counterclockwise to zoom into
the map (smaller scale, display of details), or
– Rotate the control knob clockwise, to zoom out of the
map (larger scale, more overview). You are shown the
scale
page 146, fig.155 in the side menu.
–Press the button
page 18, to leave the map
side menu.The scale can be set from 50 m to 600 km.
When you change the scale with the side menu active, this change
in scale remains only for the time the side menu is active.By pressing the button once, you leave Zoom mode and
you can use other map menu items. Pressing the button
again deactivates the active side menu.
The scales recommended for driving are:


on freeways 3.5 km


on secondary roads 750 m


in cities 200 mTips
If you have activated automatic intersection zoom
page 159, the
map display automatically changes the scale to intersections or
turn points.
A1
A
A
RETURN
RETURN
RETURN

Navigation (NAV)149
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Move map
A new destination or stopover can be set using the
map by moving the crosshairs horizontally and verti-
cally.Fig. 158 Navigation: Moving the crosshairs horizontallyFig. 159 Navigation: Moving the crosshairs vertically
–Press the Map control button in the navigation menu.
– Press the control knob to switch to the side menu.
– Rotate the control knob to the fourth menu item.
– Press the control knob, the horizontal line in the
crosshairs is highlighted in white
fig.158.
– Rotate the control knob to the desired point.
– Press the control knob, the ver tical line in the crosshairs
is highlighted in white
fig.159.
– By pressing the control knob you can switch back and
forth between horizontal and vertical movement.If the crosshairs remain in a new position, detailed information
(street or city name) is displayed for the current position .