ECO AUDI TT 2007 8J / 2.G RNS_E Navigation System Manual

Drives43
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
CD changerApplies to vehicles: with Audi cd changerLoading your CDs into the CD changerLoading just one CD
– Press the button . As soon as the CD changer
is ready for you to load a CD, the red LEDs on the inside
sides of the CD tray (not shown in the illustration)
start to blink.
– Insert the CD (printed side up and straight) into the CD
tray . The CD automatically loads into the next free slot
in the CD changer. The LED in the button will stop
blinking.Loading all CDs
– Press and hold the button for longer than 2
seconds.
– Wait until the red LEDs on the inside sides of the CD tray
(not shown in the illustration) start to blink.
– Now insert your other CDs (printed side up and straight)
o n e a t a t i m e i n t o t h e C D t r a y . Th e L E D s i n e a ch b u t t o n
will stop blinking once a CD has been loaded into the
slot.
Loading the CD into a specific empty slot
– Press the button . The LED in the button of
any empty slot will start to blink.
– If you want to load a CD into a specific slot, you can also
p r e s s a b u t t o n , w h e r e t h e L E D i s not lit a n d i n s e r t y o u r
CD.
– Wait until the red LEDs on the inside sides of the CD tray
(not shown in the illustration) start to blink.
– Now insert your CDs (printed side up and straight) into
the CD tray .
Loading the CD into a specific slot
– Press the button . The LEDs in the buttons
for the slots that already have CDs loaded blink.
– If you press an illuminated button that is not blinking
then that CD will be ejected.
– Remove the ejected CD from the CD tray .
Fig. 42 Audi cd
changer: Loading CDs
LOA D
A2
A;
A;
A3
LOA D
A2
A1
A;
A3
LOA D
A2
A
A3
A1
A;LOA D
A2
A A3
A1

Drives 44
– Insert a CD that you want to load, label up, into the CD
tray .If you press the button again while you are loading all CDs,
the loading process will be interrupted.
Make sure you load your CDs label side up and straight page 43, fig.42.
The CDs should never be forced into the slot. The CD will be pulled
into the CD changer automatically.
Aft e r a C D h as b e e n l o a d e d in to t h e CD ch a n g e r, yo u s h o u ld w a i t fo r
a moment until the red L ED on the inside side o f the tray blinks. The
CD tray is then ready to be loaded with the next CD.
If you choose a slot which already has a CD loaded in it, the CD will
be ejected. Remove the CD, and insert the new CD you want to have
in this slot.
I f yo u w a i t l o n g e r t h a n 3 0 s e c o n d s w i th o u t r e mo v in g t h e CD, th e C D
will be pulled back into the CD changer automatically.Tips


The CD is played through the main CD/SD function
page 78.


If you have accidently ins er ted a CD upside down (with the label
side facing down), the Display will show a read-error-message.


Never force the CDs into the CD tray. The CD will be pulled into
the CD changer automatically.


Do not use any non circular CDs (for example, Shape CDs)
page 49.
Applies to vehicles: with Audi cd changerEjecting CDsEjecting a CD
– Press the CD EJECT button
fig.43.
– Press the button (LED on) to eject an individual CD, or
– Press the CD EJECT button again to eject the CD you
are playing.
Ejecting all CDs
– Hold down the button for more than two seconds. All
CDs that are currently in the CD changer will be ejected.
Note

Always keep your CDs in their original cases to protect them
from dirt, dust, scratches or other damage.
A1
LOAD
A1
Fig. 43 Audi cd
changer: Ejecting CDs
A1A2A2
A1

Drives 50 Do not place an adhesive label on a CD.
Do not place an adhesive label on your CDs. Due to heat build-up
inside the CD player, the label could come loose and jam up the CD
player or CD changer.
Do not use protective rings.
Do not use commerically available protective rings. They could jam
up the player.
Cleaning your CDs
Use a soft, lint-free cloth to clean your CDs. Wipe the disc starting
f r o m t h e c e n t e r a n d w o r k i n g y o u r w a y o u t . Yo u c a n p u r c h as e s p e c i a l
cleaners to remove stubborn stains from your CD.
Never use CD cleaners which contain benzine or other corrosive
properties. They could damage your CD!Note


Never place an adhesive label on your CDs.


To prevent the CD player from malfunctioning, never use CD
protectors or stabilizers (available in most stores).


Never insert an out-of-round CD (shape CDs) in the CD slot.


Never leave your CDs exposed to direct sunlight.


The use of cleaning CDs can lead to mechanical damage to the
drive.
Tips on handling navigation DVDsTo ensure p erfect, high-quality navigatio n DVD playb ack, only clean
navigation DVDs should be used. In addition, observe the following:Do not use a damaged navigation DVD
You should not use a scratched or damaged navigation DVD. To
avoid damage, never expose the navigation DVD to direct sunlight.
Always keep the navigation DVD in a suitable jewel case (e.g. CD
case).
Do not attach labels
Do not attach labels to the navigation DVD. Attaching labels can
cause an imbalance. If the labels are exposed to heat, they can
become detached and cause damage to the navigation DVD drive.
Do not use protective rings
Co mm e r c i a ll y a v a i l a b l e p ro t e c t i v e r i n g s m u s t n o t b e us e d . Th e y c a n
jam in the navigation DVD drive and damage the drive mechanism.
Cleaning the navigation DVD
Use only a soft, lint-free cloth to clean the navigation DVD. Wipe the
DVD in a straight line from the center outwards. Heavy soiling can
be removed with a commercial CD cleaner or isopropyl alcohol.
Please never use fluids such as gasoline, paint thinner or vinyl
record cleaner or the surface of the DVD could be damaged!
Note


Never place an adhesive label on your Navigation DVD.


To a v o id d a ma g e to t h e DV D d ri v e , n e v e r us e a CD p ro t e c t i v e fi l m
or stabilizer (available in stores as a CD accessory).


Always keep the navigation DVD in a suitable jewel case (e.g. CD
case) to protect it from dirt, dust particles, scratches and other
damage.


Never expose the navigation DVD to direct sunlight.


The use of cleaning CDs can lead to mechanical damage to the
drive.
ACA

RADIO 64
–Press the Tu n i n g control button in the FM/AM radio
menu.
– Using “Manual station search”
page 62 or “Automatic
seek”
page 63, select the station (or frequency) that
you wish to save.
– By rotating and pressing the control knob, select STORE
(“Store station”)
page 63, fig.61.
– Select your desired memory location by rotating the
control knob.
– Press the control knob to save the station.Using the control wheel, you can also save manually set radio
stations
page 62.
When you save a new station, an empty memory location will be
offered automatically. You can also choose any other memory loca-
tion.
You can find additional information about radio stations starting on
page 61. In Setup radio you can delete saved radio stations from
the memory list
page 67.
Automatic station scan (SCAN)Fig. 63 Radio: SCAN function–Press the Tuning control button in the FM/AM radio
menu.
– By rotating the control knob, select SCAN
fig.63.
– Press the control knob to begin scan. The receivable
stations are played for a few seconds.To s e l e c t t h e s t a t io n t h a t i s c urre n t l y b e i n g p l a y e d , p re s s t h e c o n t ro l
knob again.

RADIO65
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Setup Radio (FM/AM range)Opening and closing SetupFig. 64 Setup Radio: Main menu– In a Radio menu, press the button to open the
main Setup menu for the radio function
fig.64.
– Press the button again to close the main Setup
menu again.The following settings are possible in Setup Radio:

Station reception
page 65


Station display
page 66


Delete stored stations
page 67The sound and tuning settings and the brightness of the display can
be entered using the control buttons
page 169.
Tips
We recommend that you enter these settings when the vehicle is
stationary. In this way, you can be sure that you are not unneces-
sarily distracted from traffic when performing the procedures that
follow. Please note
page 9, “Notes on Traffic Safety”.
Station reception (FM/AM range)
The selectivity for the automatic seek function can also
be adjusted.Fig. 65 Setup Radio: Station reception
SETUP
SETUP

RADIO 70Setup Satellite radioOpening and closing SetupFig. 70 Setup Radio XM: Main menu– In a radio menu, press the button to open the
main Setup menu for satellite radio
page 65, fig.64.
– Press the button again to close the main Setup
menu again.The following settings are possible in Setup Radio:

Sorting stations
page 70


Station info
page 71


Category filter
page 72


Receiver serial number
page 68


Delete stored entries
page 73
The sound and tuning settings and the brightness of the display can
be entered using the control buttons
page 169.
Tips
We recommend that you enter these settings when the vehicle is
stationary. In this way, you can be sure that you are not unneces-
sarily distracted from traffic when performing the procedures that
follow. Please note
page 9, “Notes on Traffic Safety”.
Applies to vehicles: with Satellite Digital Audio Radio ServiceSorting stations
S t a t i o ns c a n b e s o r t e d b y c a t e g or y o r ch a n ne l n u mb e r.Fig. 71 Setup Radio XM: Sort station by
SETUP
SETUP

RADIO73
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Applies to vehicles: with Satellite Digital Audio Radio ServiceDelete stored stationsDelete individual stations
– Press the function button in the satellite radio
menu.
–Select Delete stored stations
page 71, fig.72.
–Select Delete individually.
– Rotate and press the control knob to delete individual
stations from the memory list.
Delete all stations
– Press the function button in the satellite radio
menu.
–Select Delete stored stations.
–Select Delete all. All entries on the memory list are
deleted.Applies to vehicles: with Satellite Digital Audio Radio ServiceSystem informationThe following system messages can be displayed:XM Satellite Radio
Sirius Satellite Radio
SETUPSETUP
System mes-
sages
Meaning
ANTENNA
No antenna is connected to the tuner, or
there are loose plug contacts on the
antenna cable.
UPDATING
Your system is being updating.
NO SIGNAL
The tuner is presently not receiving any
satellite signal.
LOADING
Yo u r p ro v i d e r i s s e n d i n g i n fo r ma t i o n w h ich
the system is currently storing.
OFF AIR
The station selected has shut down its pro-
gram (e.g. children's channel at night)
INVALID
The channel is invalid or not used.
System mes-
sages
Meaning
LINKING
The tuner is presently not receiving any
satellite signal.
CALL 888-539-SIRIUS
TO SUBSCRIBE
First possibility: the tuner has not been
enabled yet. Second possibility: the station
selected is not enabled, for example
because the station requires a subscrip-
tion.

CD/SD81
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
CD Random play
CD tracks can also be played in random order.Fig. 81 CD: Random–Press the CD control button in the CD menu.
– By rotating the control knob, select MIX (“Random”)

fig.81.
– Press the control knob.The possibilities for Random play depend on the different settings
available for Repeat in the Setup CD menu
page 82.
I f y o u h a v e s w i t ch e d t he Repeat function off in Setup CD, the CDs in
a CD changer* are played one after the other in random order. The
tracks on the current CD are first played in random order. After all
the tracks have been played, the next CD is loaded.I f y o u s e t Repeat in Setup CD for only a single CD, only the tracks on
the current CD will be played in random order.
I f y o u h a v e s e t Repeat fo r a s i n g l e Tra c k in Setup CD, you cannot use
random play. The Scan function also cannot be used
page 81.
Scan CD tracksFig. 82 CD: Scanning a track–Press the CD control button in the CD menu.
– By rotating and pressing the control knob, select SCAN

fig.82.Pressing the control knob activates automatic track scan. Each track
on the CD will be played for a few seconds.

CD/SD 82When the button is pressed again, the scanning stops and the title
currently being played will continue to play.
Tips
If you have set Repeat fo r a s i n g l e Tra c k in Setup CD, you cannot use
the Scan function
page 82.
Setup CDOpening and closing SetupFig. 83 Setup CD Repeat CD (main Setup menu)– I n a C D m e n u , p r e s s t h e b u t t o n t o o p e n t h e m a i n
Setup menu for the CD function
fig.83.– Press the button again to close the main Setup
menu again.
The Repeat options
page 82 can be set in Setup CD.
The sound and tuning settings and the brightness of the display can
be entered using the control buttons
page 169.
Tips
We recommend that you enter these settings when the vehicle is
stationary. In this way, you can be sure that you are not unneces-
sarily distracted from traffic when performing the procedures that
follow. Please note
page 9, “Notes on Traffic Safety”.
Repeating CD–Press the function button
page 16 in the CD
menu.
– Select Repeat
fig.83.
– Select CD, off or Tr a c k.

Function CD: The current CD tracks are repeated.


Function off: The Repeat function is switched off.


Function Tr a c k: The CD track currently entered is repeated.Tips
The Repeat options can be combined with the Random function.
You can find more information in the description of the Random
function
page 81.
SETUP
SETUPSETUP

CD/SD87
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
– By rotating and pressing the control knob, select NAME
(“Details”) to open more detailed information about the
current track
page 86, fig.89.If information about the current track, performer, album, year of
issue, specific comments and the category has been stored in the
MP3 file, you can bring up this information using NAME (“Details”).
Tips
Because there are different methods of generating MP3 files, it is
possible that MP3 files cannot be played or information cannot be
read. You can find additional hints starting on
page 37.
Scan MP3 track (SCAN)Fig. 90 MP3: Scanning tracks on a MP3
–Press the MP3 ctrl control button in the MP3 menu.
– By rotating and pressing the control knob, select SCAN

fig.90.Pressing the control knob activates automatic track scan. Each track
on the MP3 data carrier will be played for a few seconds.
When the button is pressed again, the scanning stops and the title
currently being played will continue to play.
Tips
Because there are different methods of generating MP3 files, it is
possible that MP3 files cannot be played or information cannot be
read. You can find additional hints starting on
page 37.