check engine BMW 3 SERIES SEDAN 2014 F30 Owner's Guide
[x] Cancel search | Manufacturer: BMW, Model Year: 2014, Model line: 3 SERIES SEDAN, Model: BMW 3 SERIES SEDAN 2014 F30Pages: 242, PDF Size: 7.25 MB
Page 203 of 242

correspondingly trained personnel and other
authorized persons. Otherwise, use may result
in operating problems for the vehicle.◀
Position
There is an OBD socket on the driver's side for
checking the primary components in the vehi‐
cle emissions.
Emissions
▷The warning lamp lights up:
Emissions are deteriorating. Have
the vehicle checked as soon as
possible.
Canadian model: warning light indi‐
cates the engine symbol.▷The warning lamp flashes under certain
circumstances:
This indicates that there is excessive mis‐
firing in the engine.
Reduce the vehicle speed and have the
system checked immediately; otherwise,
serious engine misfiring within a brief pe‐
riod can seriously damage emission con‐
trol components, in particular the catalytic
converter.Seite 203MaintenanceMobility203
Online Edition for Part no. 01 40 2 925 743 - II/14 
Page 213 of 242

After a battery replacement, have the battery
registered on the vehicle by your service cen‐
ter to ensure that all comfort functions are fully
available and that any Check Control mes‐
sages of these comfort functions are no longer
displayed.
Charging the battery
Note Do not connect charging devices to the12 volt socket in the vehicle
Do not connect battery chargers to the fac‐
tory-installed 12 volt sockets in the vehicle as
this may damage the vehicle battery due to an
increased power consumption.◀
General information Make sure that the battery is always suffi‐
ciently charged to guarantee that the battery
remains usable for its full service life.
The battery may need to be charged in the fol‐
lowing cases:▷When making frequent short-distance
drives.▷If the vehicle is not used for prolonged pe‐
riods, longer than a month.
Starting aid terminals
In the vehicle, only charge the battery via the
starting aid terminals, refer to page  217, in the
engine compartment with the engine off.
Power failure After a temporary power loss, some equipment
needs to be reinitialized.
Individual settings need to be reprogrammed:
▷Seat and mirror memory: store the posi‐
tions again.▷Time: update.▷Date: update.▷Navigation system: wait for the operability
of the navigation.
Disposing of old batteries
Have old batteries disposed of by your
service center or bring them to a recy‐
cling center.
Maintain the battery in an upright position for
transport and storage. Secure the battery so
that it does not tip over during transport.
Fuses Hints Replacing fuses
Never attempt to repair a blown fuse and
do not replace a defective fuse with a substi‐
tute of another color or amperage rating; this
could lead to a circuit overload, ultimately re‐
sulting in a fire in the vehicle.◀
Plastic tweezers and information on the fuse
types and locations are stored in the fuse box
in the cargo area.
In the engine compartment
1.Use the onboard vehicle tool kit to loosen
the three cover screws, arrow 1.2.Pull up the holder, arrow 2.Seite 213Replacing componentsMobility213
Online Edition for Part no. 01 40 2 925 743 - II/14 
Page 216 of 242

if it can be established, are transmitted to
the BMW Response Center.▷If the LED is flashing, but the BMW Re‐
sponse Center can no longer be heard via
the speaker, you can nevertheless still be
heard for the BMW Response Center.
Initiating an Emergency Request
automatically
Under certain conditions, an Emergency Re‐
quest is automatically initiated immediately af‐
ter a severe accident. Automatic Collision Noti‐
fication is not affected by pressing the SOS
button.
Warning triangle
The warning triangle is located on the inside of
the trunk lid.
To remove, loosen the bracket.
First aid kit NoteSome of the articles have a limited service life.
Check the expiration dates of the contents
regularly and replace any expired items
promptly.
Storage
The first aid kit is located in the cargo area in a
storage compartment.
Roadside Assistance
Service availability
Roadside Assistance can be reached around
the clock in many countries. You can obtain as‐
sistance there in the event of a vehicle break‐
down.
Roadside Assistance The Roadside Assistance phone number can
be viewed on the iDrive or a connection to
Roadside Assistance can be established di‐
rectly.
For additional information, see user's manual
for Navigation, Entertainment and Communi‐
cation.
Jump-starting
Notes
If the battery is discharged, an engine can be
started using the battery of another vehicle
and two jumper cables. Only use jumper ca‐
bles with fully insulated clamp handles.
To prevent personal injury or damage to both
vehicles, adhere strictly to the following proce‐
dure.
Seite 216MobilityBreakdown assistance216
Online Edition for Part no. 01 40 2 925 743 - II/14 
Page 217 of 242

Do not touch live parts
To avoid the risk of potentially fatal in‐
jury, always avoid all contact with electrical
components while the engine is running.◀
Preparation1.Check whether the battery of the other ve‐
hicle has a voltage of 12 volts. This infor‐
mation can be found on the battery.2.Switch off the engine of the assisting vehi‐
cle.3.Switch off any electronic systems/power
consumers in both vehicles.
Bodywork contact between vehicles
Make sure that there is no contact be‐
tween the bodywork of the two vehicles; other‐
wise, there is the danger of short circuits.◀
Starting aid terminals Connecting order
Connect the jumper cables in the correct
order; otherwise, there is the danger of injury
from sparking.◀
The so-called starting aid terminal in the en‐
gine compartment acts as the battery's posi‐
tive terminal.
Open the cover of the starting aid terminal.
The body ground or a special nut acts as the
battery negative terminal.
Connecting the cables
1.Open the cover of the BMW starting aid
terminal.2.Attach one terminal clamp of the positive
jumper cable to the positive terminal of the
battery, or to the corresponding starting
aid terminal of the vehicle providing assis‐
tance.3.Attach the terminal clamp on the other end
of the cable to the positive terminal of the
battery, or to the corresponding starting
aid terminal of the vehicle to be started.4.Attach one terminal clamp of the negative
jumper cable to the negative terminal of
the battery, or to the corresponding engine
or body ground of assisting vehicle.5.Attach the second terminal clamp to the
negative terminal of the battery, or to the
corresponding engine or body ground of
the vehicle to be started.
Starting the engine
Never use spray fluids to start the engine.
1.Start the engine of the assisting vehicle
and let it run for several minutes at an in‐
creased idle speed.
If the vehicle being started has a diesel en‐
gine: let the engine of the assisting vehicle
run for approx. 10 minutes.2.Start the engine of the vehicle being
started in the usual way.Seite 217Breakdown assistanceMobility217
Online Edition for Part no. 01 40 2 925 743 - II/14 
Page 218 of 242

If the first starting attempt is not success‐
ful, wait a few minutes before making an‐
other attempt in order to allow the dis‐
charged battery to recharge.3.Let both engines run for several minutes.4.Disconnect the jumper cables in the re‐
verse order.
Check the battery and recharge if necessary.
Tow-starting and towing Note Tow-starting and towing
When tow-starting and towing the vehi‐
cle, switch off the Intelligent Safety systems;
otherwise, improper behavior of the braking
function of individual systems could result in
an accident.◀
Switching off Intelligent Safety systems, refer
to page  102.
Manual transmission Gearshift lever in neutral position.
Towing Follow the towing instructions
Follow all towing instructions; otherwise,
vehicle damage or accidents may occur.◀
▷Make sure that the ignition is switched on;
otherwise, the low beams, tail lamps, turn
signals, and windshield wipers may be un‐
available.▷Do not tow the vehicle with the rear axle
tilted, as the front wheels could turn.▷When the engine is stopped, there is no
power assist. Consequently, more force
needs to be applied when braking and
steering.▷Larger steering wheel movements are re‐
quired.▷The towing vehicle must not be lighter
than the vehicle being towed; otherwise,
it will not be possible to control the vehicle
response.
Tow truck
Your vehicle should be transported with a tow
truck with a so-called lift bar or on a flat bed.
Do not lift the vehicle
Do not lift the vehicle by the tow fitting or
body and chassis parts; otherwise, damage
may result.◀
Automatic transmission: transporting
your vehicle
Note Your vehicle is not permitted to be towed.
Therefore, contact a service center in the
event of a breakdown.
Do not have the vehicle towed
Have your vehicle transported on a load‐
ing platform only; otherwise, damage may oc‐
cur.◀
Seite 218MobilityBreakdown assistance218
Online Edition for Part no. 01 40 2 925 743 - II/14 
Page 220 of 242

▷Avoid lateral loading of the tow fitting, e.g.,
do not lift the vehicle by the tow fitting.
Otherwise, damage to the tow fitting and the
vehicle can occur.◀
Screw thread
Press on the mark on the edge of the cover to
push it out.
Tow-starting
Automatic transmission
Do not tow-start the vehicle.
Due to the automatic transmission, the engine
cannot be started by tow-starting.
Have the cause of the starting difficulties rem‐
edied.
Manual transmission
If possible, do not tow-start the vehicle but
start the engine by jump-starting, refer to
page  216. If the vehicle is equipped with a cat‐
alytic converter, only tow-start while the en‐
gine is cold.
1.Switch on the hazard warning system and
comply with local regulations.2.Ignition, refer to page  61, on.3.Engage third gear.4.Have the vehicle tow-started with the
clutch pedal pressed and slowly release
the pedal. After the engine starts, immedi‐
ately press on the clutch pedal again.5.Stop at a suitable location, remove the tow
bar or rope, and switch off the hazard
warning system.6.Have the vehicle checked.Seite 220MobilityBreakdown assistance220
Online Edition for Part no. 01 40 2 925 743 - II/14 
Page 222 of 242

2.Engage selector lever position N.3.Switch the engine off.
In this way, the ignition remains switched
on, and a Check-Control message is dis‐
played.
Do not turn off the ignition in the car
wash
Do not turn off the ignition in the car wash;
otherwise, selector lever position P is en‐
gaged and damages can result.◀
To start the engine:
1.Depress the brake pedal.2.Press the Start/Stop button.
Pressing the Start/Stop button without step‐
ping on the brake turns the ignition off.
The vehicle cannot be locked from the outside
when in selector lever position N. A signal is
sounded when an attempt is made to lock the
vehicle.
Selector lever position Selector lever position P is engaged automati‐
cally:
▷When the ignition is switched off.▷After approx. 15 minutes.
Headlamps
▷Do not rub dry and do not use abrasive or
caustic cleansers.▷Soak areas that have been soiled e.g. due
to insects, with shampoo and wash off with
water.▷Thaw ice with deicing spray; do not use an
ice scraper.
After washing the vehicle
After washing the vehicle, apply the brakes
briefly to dry them; otherwise, braking action
can be reduced and corrosion of the brake
discs can occur.
Completely remove all residues on the win‐
dows, to minimize loss of visibility due to
smearing and to reduce wiper noises and
wiper blade wear.
Vehicle care
Car care products BMW recommends using cleaning and care
products from BMW, since these have been
tested and approved.
Car care and cleaning products
Follow the instructions on the container.
When cleaning the interior, open the doors or
windows.
Only use products intended for cleaning vehi‐
cles.
Cleansers can contain substances that are
dangerous and harmful to your health.◀
Vehicle paint
Regular care contributes to driving safety and
value retention. Environmental influences in
areas with elevated air pollution or natural con‐
taminants, such as tree resin or pollen can af‐
fect the vehicle's paintwork. Tailor the fre‐
quency and extent of your car care to these
influences.
Aggressive substances, such as spilled fuel,
oil, grease or bird droppings, must be removed
immediately to prevent the finish from being
altered or discolored.
Leather care
Remove dust from the leather often, using a
cloth or vacuum cleaner.
Otherwise, particles of dust and road grime
chafe in pores and folds, and lead to increased
wear and premature degradation of the leather
surface.Seite 222MobilityCare222
Online Edition for Part no. 01 40 2 925 743 - II/14 
Page 233 of 242

Brake discs, breaking in 162 
Brake force display  113 
Brake lamps, brake force dis‐ play  113 
Brake lights, adaptive  113 
Brake pads, breaking in  162 
Braking, hints  163 
Breakdown assis‐ tance  215, 216  
Breaking in  162 
Brightness of Control Dis‐ play  87 
Bulb replacement  204 
Bulb replacement, front  205 
Bulb replacement, halogen headlamps  205 
Bulb replacement, rear  210 
Bulb replacement, xenon headlamps  208 
Bulbs and lamps  204 
Button, RES  122 
Button, Start/Stop  61 
Bypassing, refer to Jump- starting  216 
C
California Proposition 65 Warning  7 
Camera, care  224 
Camera, rearview cam‐ era  131  
Camera, Side View  133 
Camera, Top View  135 
Can holder, refer to Cu‐ pholder  158 
Car battery  212 
Car care products  222 
Care, displays  224 
Care, vehicle  222 
Cargo  165 
Cargo area, enlarging  154 
Cargo area, storage compart‐ ments  159 
Cargo, securing  166 Cargo straps, securing
cargo  166 
Car key, refer to Remote con‐ trol  32 
Carpet, care  224 
Car wash  221 
Catalytic converter, refer to Hot exhaust system  163 
CBS Condition Based Serv‐ ice  202  
CD/Multimedia, see user's manual for Navigation, En‐
tertainment and Communi‐
cation 
Center armrest  157 
Center console  14 
Central locking system  37 
Central screen, refer to Con‐ trol Display  16 
Changes, technical, refer to Safety  7 
Changing parts  204 
Changing wheels  212 
Changing wheels/tires  193 
Check Control  76 
Checking the oil level elec‐ tronically  198 
Children, seating position  57 
Children, transporting safely  57 
Child restraint fixing sys‐ tem  57 
Child restraint fixing system LATCH  58 
Child restraint fixing systems, mounting  57 
Child safety locks  60 
Child seat, mounting  57 
Child seats  57 
Chrome parts, care  223 
Cigarette lighter  152 
Cleaning, displays  224 
Climate control  141, 144  
Clock  79 
Closing/opening via door lock  37 Closing/opening with remote
control  35 
Clothes hooks  158 
Coasting  172 
Coasting with engine decou‐ pled, coasting  172 
Coasting with idling en‐ gine  172 
Cockpit  12 
Cold starting, refer to Starting the engine  62 
Collision warning with braking function  106 
Collision warning with City Braking function  103 
Combination switch, refer to Turn signals  65 
Combination switch, refer to Wiper system  66 
Comfort Access  39 
COMFORT program, Dy‐ namic Driving Control  117 
Compartments in the doors  157 
Compass  150 
Computer  83 
Condensation on win‐ dows  146 
Condensation under the vehi‐ cle  164  
Condition Based Service CBS  202 
Configuring drive pro‐ gram  117 
Confirmation signal  41 
ConnectedDrive, see user's manual for Navigation, En‐
tertainment and Communi‐
cation 
ConnectedDrive Services 
Connecting electrical devi‐ ces  152 
Control Display  16 
Control Display, settings  86 
Controller  16, 17  Seite 233Everything from A to ZReference233
Online Edition for Part no. 01 40 2 925 743 - II/14 
Page 235 of 242

Engine oil types, alterna‐tive  200 
Engine oil types, ap‐ proved  200 
Engine start during malfunc‐ tion  33 
Engine start, jump-start‐ ing  216  
Engine start, refer to Starting the engine  62 
Engine stop  62 
Engine temperature  78 
Entering a car wash  221 
Equipment, interior  148 
ESP Electronic Stability Pro‐ gram, refer to DSC  114 
Exchanging wheels/tires  193 
Exhaust system  163 
Exterior mirror, automatic dimming feature  55 
Exterior mirrors  54 
External start  216 
External temperature dis‐ play  79 
External temperature warn‐ ing  79 
Eyes for securing cargo  166 
F
Failure message, refer to Check Control  76 
False alarm, refer to Uninten‐ tional alarm  43 
Fan, refer to Air flow  142, 146  
Fault displays, refer to Check Control  76 
Filler neck for engine oil  199 
Fine wood, care  223 
First aid kit  216 
Fitting for towing, refer to Tow fitting  219 
Flat tire, changing wheels  212 
Flat Tire Monitor FTM  100 Flat tire, Tire Pressure Moni‐
tor TPM  97 
Flat tire, warning lamp  98, 101  
Flooding  163 
Floor carpet, care  224 
Floor mats, care  224 
Fogged up windows  142 
Fold down the rear seat back‐ rest, see Though-loading
system  154 
Fold-out position, windshield wipers  68 
Foot brake  163 
Front airbags  94 
Front fog lamps  92 
Front fog lamps, bulb replace‐ ment  209 
Front lamps  205 
Front passenger airbags, au‐ tomatic deactivation  96 
Front passenger airbags, indi‐ cator lamp  96 
FTM Flat Tire Monitor  100 
Fuel  180 
Fuel cap  178 
Fuel consumption, current  80 
Fuel consumption, refer to Average fuel consump‐
tion  84 
Fuel filler flap  178 
Fuel gauge  78 
Fuel quality  180 
Fuel recommendation  180 
Fuel, tank capacity  231 
Fuse  213 
G
Garage door opener, refer to Universal garage door
opener  148 
Gasoline  180 
Gear change, automatic transmission  70 
Gear shift indicator  81 General driving notes  162 
Glass sunroof, powered  45 
Glove compartment  156 
Gross vehicle weight, ap‐ proved  228 
H
Handbrake, refer to parking brake  65 
Hand-held transmitter, alter‐ nating code  149 
Hazard warning flashers  215 
Head airbags  94 
Headlamp control, auto‐ matic  90 
Headlamp courtesy delay fea‐ ture  89 
Headlamp flasher  66 
Headlamp glass  205 
Headlamps  205 
Headlamps, care  222 
Headlamp washer system  66 
Headliner  15 
Head restraints  47 
Head restraints, front  51 
Head restraints, rear  52 
Head-up Display  87 
Head-up Display, care  224 
Heavy cargo, stowing  166 
Height, vehicle  228 
High-beam Assistant  91 
High beams  66 
High beams/low beams, refer to High-beam Assistant  91 
Hills  164 
Hill start assistant, refer to Drive-off assistant  118 
Hints  6 
Holder for beverages  158 
Homepage  6 
Hood  197 
Horn  12 
Hotel function, trunk lid  38 
Hot exhaust system  163 
HUD Head-up Display  87 Seite 235Everything from A to ZReference235
Online Edition for Part no. 01 40 2 925 743 - II/14 
Page 237 of 242

Maintenance system,BMW  202 
Malfunction displays, refer to Check Control  76 
Manual air distribu‐ tion  142, 146  
Manual air flow  142, 146  
Manual mode, transmis‐ sion  71 
Manual operation, door lock  37 
Manual operation, exterior mirrors  55 
Manual operation, fuel filler flap  178 
Manual operation, Park Dis‐ tance Control PDC  129 
Manual operation, rearview camera  131 
Manual operation, Side View  133 
Manual operation, Top View  135 
Manual transmission  69 
Marking on approved tires  194 
Marking, run-flat tires  195 
Master key, refer to Remote control  32 
Maximum cooling  145 
Maximum speed, display  81 
Maximum speed, winter tires  194 
Measure, units of  87 
Medical kit  216 
Memory, seat, mirror  53 
Menu, EfficientDynamics  171 
Menu in instrument clus‐ ter  83 
Menus, operating, iDrive  16 
Menus, refer to iDrive operat‐ ing concept  18 
Messages, refer to Check Control  76 
Microfilter  143, 146  
Minimum tread, tires  193 Mirror  54 
Mirror memory  53 
Mobile communication devi‐ ces in the vehicle  163 
Modifications, technical, refer to Safety  7 
Moisture in headlamp  205 
Monitor, refer to Control Dis‐ play  16 
Mounting of child restraint fix‐ ing systems  57 
Multifunction steering wheel, buttons  12 
N Navigation, see user's manual for Navigation, Entertain‐
ment and Communication 
Neck restraints, front, refer to Head restraints  51 
Neck restraints, rear, refer to Head restraints  52 
Neutral cleaner, see wheel cleaner  223 
New wheels and tires  193 
No Passing Information  81 
Nylon rope for tow-starting/ towing  219 
O OBD Onboard Diagnosis  202 
OBD, see OBD Onboard Di‐ agnosis  202 
Obstacle marking, rearview camera  132 
Octane rating, refer to Rec‐ ommended fuel grade  180 
Odometer  79 
Office, see user's manual for Navigation, Entertainment
and Communication 
Oil  198  
Oil, adding  199 
Oil additives  199 Oil change  200 
Oil change interval, service requirements  80 
Oil filler neck  199 
Oil types, alternative  200 
Oil types, approved  200 
Old batteries, disposal  213 
Onboard monitor, refer to Control Display  16 
Onboard vehicle tool kit  204 
Opening/closing via door lock  37 
Opening and closing  32 
Opening and closing, without remote control  37 
Opening and closing, with re‐ mote control  35 
Operating concept, iDrive  16 
Optional equipment, standard equipment  6 
Outside air, refer to Auto‐ matic recirculated-air con‐
trol  145  
Overheating of engine, refer to Coolant temperature  78 
P Paint, vehicle  222 
Parallel parking assistant  136 
Park Distance Control PDC  128 
Parked-car ventilation  147 
Parked vehicle, condensa‐ tion  164 
Parking aid, refer to PDC  128 
Parking assistant  136 
Parking brake  65 
Parking lamps  89 
Particulate filter  163 
Parts and accessories  7 
Passenger side mirror, tilting downward  55 
Pathway lines, rearview cam‐ era  131  Seite 237Everything from A to ZReference237
Online Edition for Part no. 01 40 2 925 743 - II/14