BMW 325Ci CONVERTIBLE 2001 E46 Workshop Manual
Manufacturer: BMW, Model Year: 2001, Model line: 325Ci CONVERTIBLE, Model: BMW 325Ci CONVERTIBLE 2001 E46Pages: 215, PDF Size: 2.1 MB
Page 51 of 215
51n
IndexDataTechnologyRepairsCar careControlsOverview
Wind deflector
*
2 Flip out both side pieces and lock
into place (arrow).46cde098
Hold the wind deflector so that the
smaller half faces toward the
front.<
3 Guide the mounting pin for the side
piece into the proper opening.
4 Pull back on the mounting pin for the
other side piece by using the slide, so
that the mounting pin can be guided
into the opening provided.
5 Unlock the convertible top compart-
ment lid; see page 45 or 49, and
open the convertible top compart-
ment lid.
6 Flip the back half of the wind
deflector backward, so that the
mounts are lying on the vehicle.
46cde099
7 Close the convertible top compart-
ment lid. The wind deflector is now
attached so that it is theft-proof.
Operate the convertible top
compartment lid from above only
to avoid any pinching.
With the wind deflector in place: never
push the front seats all the way back to
avoid damaging the wind deflector.
Page 52 of 215
52n
For your personal safety when adjusting
the seat position, please follow the
instructions below carefully:
Never try to adjust your seat while
driving the vehicle. The seat could
respond with an unexpected move-
ment, and the ensuing loss of vehicle
control could lead to an accident.
Be sure that the safety belt remains
firmly against your body at all times. In
the event of a frontal impact, a loose lap
belt could slide over the hips, leading to
abdominal injury. In addition, the safety
belt's restraint effectiveness is reduced
if the belt is worn loosely.
Never ride with the backrest reclined to
an extreme angle (especially important
for the front passenger to remember),
otherwise, you run the risk of sliding
under the safety belt during an acci-
dent, thus negating the protection the
safety belt provides.<
Correct sitting postureTo reduce strain on the spinal column,
sit all the way back in the seat and rest
your back fully against the backrest.
The ideal sitting posture is achieved
with your head extending from your
spine in a straight line.
For long-distance driving, you may wish
to increase the backrest angle slightly
to reduce muscular tension. You should
be able to grasp the steering wheel at
its highest point with your arms slightly
bent.
1 Backward/Forward adjustment
2 Cushion height
3 Backrest angle
Follow the setting instructions on
this page. Failure to do so could
result in diminished personal safety.<
46cde012
Seat adjustment
Page 53 of 215
53n
IndexDataTechnologyRepairsCar careControlsOverview
Head restraints Front headrests1 Height
Head restraints reduce the risk of
injury to the cervical vertebra in
the event of an accident.
Adjust the head restraint so that its
center is approximately at the height of
your ears.
When moving the headrests up or
down, do not reach between the head-
rest and the upper edge of the backrest
to avoid the possibility of injury.<46cde029
2 Tilt angle
Position the headrest in the preferred
position. 46cde087
Rear headrests
The rear headrests are to be
lowered only if there are no
passengers riding in the back. Raise the
rear headrests before taking on any
passengers in the back.<
To completely lower the headrests in
the back:
1 Press the button (arrow) and hold it
down.
2 Push the headrest down from above.
46cde100
Page 54 of 215
54n
Head restraints BMW sports seat
*
Raising the rear headrestsRaise the headrests until you feel them
click into place.
Do not remove the rear headrests,
as this would damage them.<
For further information, please consult
your BMW center.
Do not use the rear headrests as
storage shelves. Always keep the
travel path clear for the rollover protec-
tion system. Under no circumstances
should you put any kind of protective
cover on the headrests (refer also to the
labeling on the headrests).<
1 Tilt angle
2 Backward/Forward adjustment
3 Cushion height
4 Backrest angle
Please refer to the adjustment
instructions on page 52 to reduce
the risk of personal injury.<46cde013
5 Thigh support
>Pull the lever and adjust the position
of the cushion for thigh support as
desired.46cde040
Page 55 of 215
55n
IndexDataTechnologyRepairsCar careControlsOverview
Entering the rear Lumbar support
*
The seat-integrated safety belt allows
easy access to the rear. You do not
need to adjust the safety belts. They
automatically adapt to various body
sizes.
1 Lift the lever (1) up and tilt the back-
rest forward.
2 Press the switch (2) toward the front
of the car and hold it there until the
seat moves to the desired position.
You can lock a backrest that has
been tilted forward. This makes
sense when, for instance, someone is
climbing into the rear on an incline. To
do this, press against the backrest until
you hear it click into place. To move it
back into place, you do not need to
unlock it by moving the lever (1).<46cus029
If you tilt the backrest back and hold the
switch (2) pressed toward the back of
the vehicle, the seat will return to its
former position.
If you let go of the switch (2)
before the seat has returned to its
former position, it will remain in the
position where you leave it. To move it
back into place, you do not need to
unlock it by moving the lever (1).<
Lock both backrests while driving,
as otherwise there is danger of an
unexpected movement causing an
accident. The indicator lamp in the
instrument cluster flashes if the back-
rest is not locked, refer to page 21.
Then the indicator lamp comes on until
the safety belt is fastened.<
You can adjust the backrest's contour
for additional support in the curvature
of your spine's lumbar region.
The upper hips and spinal column
receive supplementary support to help
you maintain a relaxed, upright posture.
>Press front/rear of switch:
Increase/decrease curvature.
>Press the upper/lower end of the
switch:
Increase the upper/lower curvature.46cde011
Page 56 of 215
56n
Seat and mirror memory*You can store and recall three different
driver's seat and exterior mirror posi-
tions. The illustration shows the buttons
on the driver's seat for making these
adjustments.
The headrest setting is stored in
the memory, but the lumbar
support is not.
exterior mirror positions.
3 Press the
M
EMORY button: the indi-
cator lamp in the button lights up.
4 Press memory button 1, 2 or 3, as
desired: the indicator lamp goes out.
46cde014
To select a stored settingConvenience function:
1 Open the driver's door after
unlocking or turn the ignition key in
position 1.
2 Briefly press memory button 1, 2 or 3,
as desired.
The adjustment cycle is canceled
immediately if you press a seat
adjustment switch or one of the
memory buttons.
Security function:
1 With the driver's door closed and the
ignition key either removed or in posi-
tion 0 or 2.
2 Maintain pressure on the desired
memory button (1, 2 or 3) until the
adjustment process is completed.
If you accidentally press the
M
EMORY
button: press the button again; the
indicator lamp goes out.
Do not select a memory position
while the vehicle is moving. If you
do so, there is a risk of accident from
unexpected seat movement.<
Your BMW center can adjust your
vehicle's systems in such a
manner that your personalized settings
are automatically set for the seat, head-
rest and exterior mirror positions when
you unlock the vehicle with your
personal remote control.<
If you make use of this method of
adjustment, be sure that the foot-
well behind the driver's seat is unob-
structed before unlocking the vehicle.
If you fail to do so, persons or objects
could be injured or damaged if the seat
should move backward.<
Page 57 of 215
57n
IndexDataTechnologyRepairsCar careControlsOverview
Seat and mirror memory*
Adjusting steering wheel Mirrors
Passenger side exterior mirror tilt
function(automatic curb monitor
*)
1 Move the mirror selector switch 1 to
the "driver's mirror" position.
2 When the selector lever is placed in
"Reverse," the passenger-side mirror
tilts downward. This allows the driver
to see the area directly adjacent to
the vehicle during parking (curbs,
etc.).
You can deactivate this automatic
feature: set the mirror selection switch
to the "passenger side" position.
462us058
1 Push the locking lever downward.
2 Adjust the steering wheel (fore/aft
and up/down) to the desired position.
3 Pull back the lever again to clamp the
steering wheel in the new position.
Do not adjust the steering wheel
while the vehicle is moving. If you
do so, there is a risk of accident from
unexpected movement.<460de073
Exterior mirrors1 Switch for 4-way adjustment
2 Selection switch for changing
between mirrors462us057
Page 58 of 215
58n
MirrorsYou can also adjust the mirrors manu-
ally by pressing against the outer edges
of their lenses.
The mirror on the passenger's
side features a lens with a more
convex surface than the mirror installed
on the driver's side. When estimating
the distance between yourself and
other traffic, bear in mind that the
objects reflected in the mirror are closer
than they appear. Estimations of the
distance to following traffic should
therefore not be regarded as precise.
Interior rearview mirror To reduce glare from vehicles behind
you when driving at night, tilt the mirror
by turning the rotary button.Sun visorsThese can be folded down toward the
windshield and swiveled out against the
side window.46cus034
Interior rearview mirror with
automatic dimming feature
*
By responding to the effects of ambient
light and the glare from following traffic,
this mirror automatically dims through
an infinitely-variable range.
The mirror switches to its clear,
undimmed mode whenever the trans-
mission is placed in reverse gear
(selector lever in "Reverse").
To ensure that the mirror continues to
operate properly, keep the two photo-
cells clean and unobstructed. One
photocell (arrow) is in the mirror glass,
while the other is offset somewhat on
the other side of the mirror.
For addition information on the electro-
chromic technology used in this mirror,
refer to page 191.46cde023
Page 59 of 215
59n
IndexDataTechnologyRepairsCar careControlsOverview
Car Memory, Key Memory How the system functionsYou have probably frequently wished
that you could configure individual
functions of your vehicle to reflect your
own personal requirements. In engi-
neering your vehicle, BMW has
included several user-defined func-
tions in the vehicle's design. Your BMW
center can make these settings for you
in accordance with your wishes.
There are settings related to the vehicle
("Car Memory") and settings related to
individuals ("Key Memory"). You can
have up to four different basic settings
adjusted for four different persons. The
only requirement is that each person
uses his or her own remote control key. 463de029
When your vehicle is unlocked with the
remote control, the vehicle recognizes
the individual user by means of a data
exchange with the key, and makes
adjustments accordingly.
In order for you to distinguish between
different keys, colored decals are
supplied together with the keys.
What the system can doYour BMW center can provide you with
details on the capabilities of the Car
Memory and Key Memory systems.
A few examples follow below:
Examples for Car Memory:
>Various signals used as acknowl-
edgement when locking or unlocking
your vehicle.
>Deactivating/activating the Follow-
Me-Home lamps function.
>Activating/deactivating daytime
running lamps
*.
Examples for Key Memory:
>Automatic adjustment of the driver's
power seat.
>Locking your vehicle after starting off.
>When unlocking your vehicle, first
unlock the driver's door, then the rest
of the vehicle.
You will see this symbol
throughout the Owner's Manual. It
is to remind you at appropriate places
of the settings that are available to
you.<
Page 60 of 215
60n
Drive with your safety belt onFasten your safety belt at the beginning
of every trip.
To fasten:
Make sure you hear the catch engage in
the belt buckle.
To release:
Press the red button in the buckle, hold
the belt firmly and guide it back into its
reel.
The safety belt system will automati-
cally adapt to your body contours.
Before putting on your safety belts
in the rear, take them out of the
holder.<
For care instructions, refer to page 154.46cus022
For your safety, please comply
with the following instructions for
wearing safety belts. If you do not, the
safety belts may not be able to provide
their maximum protection. The
following information also applies to
your passengers:
Never allow more than one person to
wear a single safety belt. Never allow
infants or small children to ride in a
passenger's lap.
Avoid twisting the belt while routing it
firmly across your hips and shoulder.
Do not allow the belt to rest against
hard or fragile objects in your pockets.
Never route the belt across your neck,
do not run it across sharp edges and
ensure that the belt does not become
caught or jammed.
Avoid wearing clothing that prevents
the belt from fitting properly. Pull on the
belt periodically to readjust the tension
across your shoulder. In the event of a
frontal impact, a loose lap belt could
slide over your hips, leading to abdom-
inal injury. In addition, the safety belt's
restraint effectiveness is reduced if the
belt is worn loosely.
Expectant mothers should always wear
the safety belt, taking special care to
place the lap belt over the lower hips,
where it does not exert pressure on the
abdominal area.
Leave the rear safety belts in the
holders if they are not needed to avoid
unwanted movement from the safety
belts at high speeds.<
For child restraint system installation,
refer to page 64.
If the safety belt system has been
subjected to the stresses involved
in an accident or otherwise damaged:
Have the entire safety belt mechanism
replaced by your BMW center,
including the safety belt tensioner. In
addition, have your BMW center
inspect the safety belt anchors. If a
child restraint system was in the vehicle
during an accident, consult the manu-
facturer's instructions regarding
replacement.<
Safety belts