buttons BMW 328Ci CONVERTIBLE 2000 E46 Owner's Manual

24n
Multifunction steering wheel (MFL)The buttons integrated in the multifunc-
tion steering wheel are provided so that
you can operate a number of accesso-
ries quickly and without being distracted
from traffic conditions. You can operate:
>selected radio functions
>the cruise control
>selected cellular phone functions.
In order to operate a system via
the MFL, the corresponding sys-
tems must be switched on.<
1 Radio/Cellular phone: select
2 Cellular phone: receive a call, start
dialing, terminate a call
3 Radio/Cellular phone: volume
4 Radio/Cellular phone: scan backward
or station buttons or scroll through
the phone listings
5 Radio/Cellular phone: scan forward
or station buttons or scroll through
the phone listings46cde085
6 Horn: the entire surface
7 Cruise control: activate stored
setting (resume)
8 Cruise control: store and accele-
rate (+); decelerate and store (–)
9 Cruise control: activate/interrupt/
cancel.

34n
Central locking system Opening and closing – from outside The conceptThe central locking system is ready for
operation whenever the driver's door is
closed. The system engages and re-
leases the locks on the
>doors
>luggage compartment lid
>fuel filler door
>glove compartment.
The central locking system can be
operated
>from outside via the door lock and
using the remote control
>from inside by pressing a button.
Activating the central locking system
from inside does not lock the fuel filler
door (refer to page 38). Operating it
from the outside simultaneously acti-
vates the anti-theft protection. Both the
door locks and release handles remain
locked. The alarm system
* is also
armed or disarmed.
In the event of an accident, the central
locking system unlocks automatically
(only those doors that were not locked
separately with the safety lock buttons).
Refer to page 38. In addition, the ha-
zard warning flashers and interior lamps
come on.
Using the keyTurning the key in the driver's door
once unlocks the driver's door only.
Turning the key a second time unlocks
all of the remaining doors, the luggage
compartment lid, the fuel filler door and
the glove compartment.
You can have a signal set as an
acknowledgement message that
the vehicle is closed correctly.<460de006
Convenience operating modeYou can also operate the power win-
dows and the fully automatic convert-
ible top
* using the door lock.
>To open: with the door closed, turn
the key to the "Unlock" position and
hold it
>To close: with the door closed, turn
the key to the "Lock" position and
hold it.
Watch during the closing process
to make sure that nobody is in-
jured accidentally. Releasing the key
stops the operation.<
Manual operation (in the event of electrical malfunction)
Turn the key all the way to the extreme
left or right to unlock/lock the door.

50n
The fully automatic convertible top
*
Opening and closing1 Closing
2 Opening
Keep pressing the button for operating
the convertible top until the opening or
closing process has ended.
The side windows will lower slightly
during the opening process. If you
continue to press the button after the
convertible top has been closed and
locked, the side windows will close,
too.
The red indicator lamp lights up while
the convertible top is being operated.
After releasing the button, the lamp will
start blinking if the opening or closing
process has not been fully completed.46cus004
If the convertible top compartment
panel has been raised, then the con-
vertible top cannot be moved. In this
event, the yellow indicator lamp stays
on when the button is pressed and indi-
cates that it is not possible to operate
the convertible top.
Flip the convertible top compartment
panel down, refer to page 41.
If the opening or closing process
has been interrupted, then the
convertible top will remain stationary
in that position for 15 minutes.
After that, the convertible top can be
operated manually. This can also be
carried out with the ignition key in
position 0.
The luggage compartment cannot be
opened while operating the convertible
top.
The side windows are lowered slightly
when pressing the convertible top but-
ton and are raised back up after com-
pleting the opening process, if you have
continued holding the button down for
more than 2 seconds after the indicator
lamp has gone out.c
While the convertible top is
moving, the side windows lower
slightly. If the convertible top closing
or opening operation is interrupted, do
not close the side windows by using the
power window buttons.
Sometimes the luggage compartment
lid cannot be opened, either, if the
opening or closing process has been
interrupted.
To avoid any damage from constant
damp, never put the convertible top
away wet.
The rear window will move toward the
passenger area while the convertible
top is in operation, and it will also lightly
press the heads of the passengers sit-
ting in the rear toward the front. As a
rule, there is no danger in this. To avoid
any possible pinching, however, the
rear passengers should tilt their heads
slightly forward while the convertible
top is in motion.c

57n
IndexDataTechnologyRepairsCar careControlsOverview
Seat and mirror memory
*
You can store and recall three different
driver's seat and outside mirror posi-
tions. The illustration shows the buttons
on the driver's seat, for making these
position adjustments.
The setting for the head restraint
is stored in memory, but the set-
ting for the lumbar support is not. 1 or 2
2 Set the desired positions for the seat,
head restraint and outside mirror
3 Press the
M
EMORY button: the indi-
cator lamp in the button lights up
4 Press memory button 1, 2 or 3, as
desired. Indicator lamp goes out.
46cde014
To select a stored setting Convenience function:
1 Open the driver's door after unlock-
ing or set the ignition key in posi-
tion 1
2 Briefly press memory button 1, 2 or 3,
as desired.
The adjustment cycle is canceled im-
mediately if you press a seat adjust-
ment switch or one of the memory
buttons.
Security function:
1 With the driver's door closed and the
ignition key either removed or in posi-
tion 0 or 2
2 Maintain pressure on the desired
memory button (1, 2 or 3) until the
adjustment process is completed.
If you press the
M
EMORY button acci-
dentally: press the button again; the
indicator lamp goes out.
Do not select a memory position
while the vehicle is moving. If you
do so, there is a risk of accident from
unexpected seat movement.<
Your BMW center can adjust your
vehicle's systems in such a man-
ner that your personalized settings are
automatically set for the seat, head
restraint and outside mirror positions
when you unlock the vehicle with your
personal remote control.<
If you make use of this method of
adjustment, be sure that the foot-
well behind the driver's seat is unob-
structed before unlocking the vehicle.
If you fail to do so, any persons or ob-
jects behind the seat could be injured
or damaged by a rearward movement
of the seat.<

88n
Dynamic Stability Control (DSC) The conceptDSC helps maintain vehicle stability,
even in critical driving situations.
The system optimizes vehicle stability
during acceleration and when starting
from a full stop, as well as optimizing
traction. In addition, the system recog-
nizes unstable vehicle conditions (un-
dersteering or oversteering, for exam-
ple) and helps hold the vehicle on a
sure course by intervening via the
engine and by braking intervention at
the individual wheels.
The system activates automatically
each time you start the engine.46cus012
Indicator lamp
The indicator lamp in the instru-
ment cluster goes out shortly
after you switch on the ignition.
Refer to pages 21 and 22.
Indicator lamp flashes:
The system is active and governs drive
force and braking force.
If the indicator lamp fails to go out after
the engine is started, or if it comes on
during normal driving and stays on:
There is a system malfunction or the
system was deactivated with the but-
ton. You can continue to drive the vehi-
cle normally, but without DSC. Please
consult your BMW center for repairs.
To deactivate the systemPress the button, the indicator lamp
comes on.
The illustration depicts the arrangement
of the buttons if the vehicle is fully
equipped. This may vary, depending on
the equipment actually installed.
When the DSC is deactivated, you are
operating the vehicle in the conven-
tional drive mode.
In the following exceptional circum-
stances, it may be effective to deacti-
vate the DSC for a short period:
>When rocking the vehicle or starting
off in deep snow or on loose surfaces
>or when driving with snow chains.
Refer also to page 118.To reactivate the systemPress the button again; the indicator
lamp goes out.
The laws of physics cannot be re-
pealed, even with DSC. Any con-
sequences arising from traction loss
due to excessive vehicle speed remain
the responsibility of the driver. For this
reason, do not take risks by using the
additional safety margin provided by
the system as an excuse.<
For additional details concerning DSC,
please refer to the chapter describing
"Advanced technology" on page 173.

101n
IndexDataTechnologyRepairsCar careControlsOverview
BMW Universal Transmitter
*
Programming 1 Channel keys
2 Indicator lamp
Read and comply with the safety
precautions on the previous
page.<
1 Turn the ignition key to position 2
2 To initialize: press and hold both out-
side keys 1 until the indicator lamp 2
flashes, and then release them. The
three channel keys are cleared46cus023
3 Hold the original hand-held transmit-
ter to the receiver embedded in the
mirror, e. g. right near the buttons, no
further than 2 inches away (5 cm)
4 Press the transmission key of the orig-
inal hand-held transmitter (arrow 2)
and the desired channel key of the
Integrated Universal Remote Control
(arrow 1) simultaneously. Release
both keys as soon as the indicator
lamp flashes rapidly
5 To program other original hand-held
transmitters, repeat steps 3 and 4.
The corresponding channel key is now
programmed using the signal from the
original hand-held transmitter. 46cus024
Programming a hand-held
transmitter with conversion code
Read and comply with the safety
precautions on previous page.<
When programming the BMW Universal
Transmitter, consult the instructions for
the specific device. For using the BMW
Universal Transmitter with a conver-
sion-code system, note the following
supplemental programming instruc-
tions:
A second person facilitates pro-
gramming of the BMW Universal
Transmitter.<
1 Program the BMW Universal Trans-
mitter as described previously under
"Programming"
2 Press and hold the programming key
on the receiver of the device for ap-
proximately two seconds until the
programming lamp on the device
comes on
3 Press the desired channel key of the
BMW Universal Transmitter three
times.
If you have additional questions,
please consult your BMW center.<

122n
Hardtop
*
4 Open both front locking levers. To do
this press the buttons. The levers will
loosen somewhat. Flip the levers
open until they hit the stop46cde0089
5 Fold the cover panels that are on
the right and left side and below the
interior lamps downward before
mounting the hardtop. Press against
the small bulge on the cover panel.
There is a bracket in the cover panel
for secure storage of the the trim
pieces that have been removed (1)
6 Open the red locking lever all the
way (2)
7 Position the hardtop onto the sup-
ports with the help of a second per-
son. Be sure to place the supports
right in the brackets provided
8 In the back, close the red locking
levers by turning them inward until
they hit the stop behind the trim. Fold
the cover panels back 46cde077
9 To lock the hardtop in front, keep
closing the front locking levers until
you hear them engage.
Raise the hardtop carefully. Be
very careful not to displace the
seals. Seals that have been accidentally
displaced or pulled out lead to leaks.cRemovingRemove the hardtop in the opposite
order of installation.

Everything from A to Z
193n
IndexDataTechnologyRepairsCar careControlsOverview
Manual transmission73
Manually controlled
recirculated-air97
Memory57
MFL (Multifunction steering
wheel)24
Mirror memory57
Mirrors58
Mobile phones120
Modifications,
technical6, 148
Multifunction steering wheel
(MFL)24NNavigation system, refer to
the Radio Owner's ManualOOBD interface socket149
Odometer82
Oil
additives133
capacity185
consumption133
dipstick133
quality134
specifications134
viscosity134
Oil change intervals, see the
Service and Warranty
Information BookletOil filter change185
Oil level
check133
Indicator lamp20
Oil pressure, indicator
lamp20
OILSERVICE83
Onboard computer85
also refer to separate
Owner's Manual
Onboard tool kit152
Opening and closing
from inside38
from outside34
Operating the convertible
top
manual convertible top45
Outlets, ventilation94
Outside temperature
display85
PPaint blemishes140
Paint, care140
Paintwork, minor
repairs141
Paintwork, waxing141
Park Distance Control
(PDC)87
Parking brake72
Parking help87
Parking lamps92Parking, winter119
PDC (Park Distance
Control)87
Performance182
Pocket lamp99
Pollen98
Power seats53
Power steering120
Power windows44
Pressure monitoring,
tires89, 177
Pressure, tires27, 123
RRadiator185
Radio Data System
(RDS)174
Radio reception120, 174
Radio, refer to the separate
Owner's Manual
Rain sensor78, 176
RDC (Tire Pressure
Control)89, 177
RDS (Radio Data
System)174
Reading lamps93
Rear lamp155
Rear window
defroster79, 98
Rearview mirror58, 59
Reclining seat53
Refueling26Remote control35
Remote control key32
Remove condensation,
windows97
Replacement key32
Reporting safety defects7
Restraint system61, 66
Reverse17, 73
Rollover protection
system68, 179
lowering68
Roof load capacity184
Roof luggage rack108
Roof-carrier assembly121
Rubber parts118
SSafety belt tensioners174
Safety belts61
Safety buttons38
Seat heating99
Seat memory57
Seat-integrated safety belt
system56
Seats
sitting properly53, 64
Securing cargo107
Securing loads107
Selector lever, automatic
transmission74
Self-defrosting mirrors59
Self-diagnostics178