heater BMW 525I 1998 E39 Central Body Electronics ZKE Manual

12
Central Body Electronics ZKE III
Rain Sensor (AIC - if equipped)
Purpose of the System
The Windshield Wiping System is also available with an optionally equipped Rain Sensor.
The Rain Sensor provides added driver convenience and enhances safety by automatical-
ly activating the intermittent function of the windshield wipers when water droplets are
detected on the windshield.
System Components
Rain Sensor: The unit is mounted on the top center area of the interior windshield surface
directly behind the rear view mirror. The unit contains:
• Optical Prism Body:This portion of the unit is per-
manently fixed to the windshield. It can not be
removed and can only be replaced with a replacement
windshield.
The prism body has a reflective surface that faces the
back of the windshield. The prism body also acts as
the windshield mount for the Rain Sensor Control
Module.
• Rain Sensor Control Module:The control module incorporates the following;
- Infra Red Emitter and Detector Diodes
- Optics heater (prevents condensation from forming on diodes and prism)
- Optics evaluation and control electronics
- Photo cell to detect night driving
The control module requires four signals for operation; KLR, KL31, Windshield Wiper Motor
Park Signal Feedback and K-Bus interface.
12510112.jpg
GM III
12510113.eps

The Remote Entry System incorporated minor changes since the original introduction
which includes:
• The control electronics are incorporated into the GM III.
• The antenna is incorporated into the rear window lower heater grid.
• The remote key receiver is installed in the left “C” pillar. The receiver produces a digital
signal based on the transmitter command and sends it to the GM for processing. The GM
then carries out all remote entry operations either directly or through the door modules
for the front doors. The frequency at which the key transmits the radio signal to the ant-
enna amplifier is 315 MHz.
Vehicle/Key Memory
The Vehicle/Key Memory feature provides the flexibility of allowing the owner to customize
certain functions of select vehicle systems and automatically identifies users of the vehicle
by a key identification signal provided by the remote keyless entry system (FZV).
Vehicle & Key memory is marketed as a combined feature but is actually two separate func-
tions of the select vehicle control systems.
27
Central Body Electronics ZKE III
A
IHKA
K-BUSKEY #1
KEY #2
KEY #3
KEY #4
GMV
SM
Adjust Setting of Seat
For Key #1 IHKA Features Key #1
Being Used
KEY 4
KEY 3
KEY 2
KEY 1
KEY 1
- Selective Unlocking
- Automatic Locking
615200099.eps

67
Central Body Electronics ZKE III
Seat Heating Operation (from 99 MY)
Principle of Operation
The front seat heaters are adjustable through three ranges of
heating output temperature.
Pressing the respective seat heater button once provides
stage 1:
• All three LEDs illuminate and the heating elements are provided regulated output current
producing a seat temperature of 111
OF.
Pressing the button a second time provides stage 2:
• The top LED switches off and the heating elements are regulated to an output tempera-
ture of 102
OF.
Pressing the button a third time provides stage 3.
• The top and middle LEDs are off and the heating elements are regulated to an output tem-
perature of 95
OF.
The SZM monitors the seat heating element temperature via an NTC feedback signal to
regulate the output current which maintains the seat temperature.
Seat heating is switched off by pressing the button a fourth time,
pressing and holding the
button for more than 1 second or when the ignition is switched off.
System Components
Carbon Fiber Heating Pads:In each seat is a two
section heating pad wired in parallel. The heating pads
are resistors which when powered produce radiant
heat.
The seat base heating element also contains a temper-
ature sensor for feedback to provide the temperature
regulation output control.
KL31
KL15
TEMPERATURE
SENSOR
615200139.eps