installing AC BMW 528i 2000 E39 Workshop Manual

Downloaded from www.Manualslib.com manuals search engine
41 2 Trunk Lid. Tailgate
........................... General
......................... Trunk Lid
Trunlc lid. removing and installing ........
Trunk lid. adjusting ...................
Trunk lid support strut.
removing and installing
................
Tailgate (Sport Wagon Models) .....
Tailgate. emergency release ...........
Tailgate and window strut diagram .......
Window strut removal diagram .......... 412-8
Rear window gas strut.
removing and installing
................ 412-9
Tailgate gas strut. removing and installing
............... 412-10
Tailgate. removing and installing
........ 412-1 1
Rear window. removing and installing
.... 412-12
Rear window and tailgate. alignment
..... 412-13

Downloaded from www.Manualslib.com manuals search engine
41 2-2
Trunk Lid, Tailgate
This repair group covers trunk lid and tailgate removal and in-
stallation. Also included here are replacement proceduresfor
the gas-charged support struts that hold the trunk lid or tail-
gate in the open position.
NO JE -
The body is painted at the factory after assembly. Realign-
ment of body panels may expose unpainted metal. Paint all
exposed metal once the
work is complete.
Trunk lid, removing and installing
4 Raise trunlc lid.
Open tool ltit cover and remove screws attaching tool kit to
trunlc lid (black arrows).
Disconnect tool ltit cover retaining strap from
trunk lid and
remove tool kit.
Remove insulating liner expansion rivets (white arrows).
4 Pry out moulded trim cover (arrow).

Downloaded from www.Manualslib.com manuals search engine
. .- -
l~runk Lid, Tailgate
Trunk lid support strut, removing and
installing
/ Make sure to supporf trunk lid before removing struts. I
Open trunk lid and support in open position.
Remove trunk strut retaining clip
(arrow) and disconnect
struts.
4 Remove spring clip (arrow) from lower end of strut and re-
move strut.
- Installation is reverse of removal. Replace retaining clips
damaged during removal.
Tailgate, emergency release
The tailgate of the E39 Sport Wagon has no ltey cylinder. An
emergency release mechanism is incorporated into the tail-
gate latch. This allows mechanical opening of the latch in
case of an electrical failure. The release is located in the rear
cargo area, along the lower edge of the rear apron behind a
small access cover.
Working inside car, at base of tailgate:
Open tool compartment cover.
Pry out emergency release cable cover.
Pull plastic cable to release rear tailgate latch

Downloaded from www.Manualslib.com manuals search engine
. .- -
Trunk Lid, Tailgate
Rear window gas strut, removing and
installing
- Tailgate and window struts are located in left and right sides
of roof.
- Open rear window.
WARNING-
The tailgate is very heavy and will close without both pressu-
rized lifting struts installed. Properly support tailgate prior to
removal of the lifting struts.
< Remove fasteners (A) from rear window hinge trim cover,
< While pressing detents (A) and (6) pull down (arrow) on trim
panel to remove.
- Close rear window and open tailgate and support.
- Remove weather stripping along rear of roof panel.
< Remove tailgate hinge trim panel fasteners (A).

Downloaded from www.Manualslib.com manuals search engine
.-
l~runk Lid, Tailgate
Starting at top, pull down (arrow) on trim cover. Carefully re-
move wiring harness support clip from trim cover.
NOTE-
Tailgate window trim cover and weather stripping shown in
place.
Insert BMW special tool 51 2
153 into body cavity below
hinge.
WARNING-
Tlie tailgate is ve!y heavy and will close without both pressu-
rized liftinq struts installed. Properly support
tailgafe prior to r
1 removal of the lifting struts.
- Working at hinge end of strut, remove strut retaining clip and
remove strut from mounting pin.
Slide BMW special tool 51 2 152 over strut until end of tool is
aligned with strut pin
(arrow).
Press down on outer end of special tool to release inner
strut mount.
Remove special tool with strut.
When installing strut make sure ball cup is pointing straight
down.
Rema~nder of installation 1s reverse of removal.
Tailgate gas strut, removing and installing
- Open tailgate and support.
Remove tailgate hinge trim panel fasteners
(A).

Downloaded from www.Manualslib.com manuals search engine
Trunk Lid, Tailgate
Starting at top, pull down (arrow) on trim cover. Carefully re-
move wiring harness support clip from trim cover.
Install protective plate
(BMW special tool 51 2 153) between
roof panel and hinges.
WARNING -
The tailgate is very heavy and will close without both pressu-
rized lifting
struts installed. Properly support tailgate prior to
removal of the lifting struts.
Worlting at left side:
Remove gas strut retaining clip and pin (arrow).
4 Insert BMW special tool 51 2 151 over strut.
NOTE-
BMW special tool 51 2 151 must be chamfered in area (A).
Press tool down to release inner end of gas strut.
Push strut forward and toward center of vehicle to remove.
- When installing strut make sure ball cup is pointing straight
down.
- Remainder of installation is reverse of removal.
Tailgate, removing and installing
- Remove radio antenna amplifier. See 650 Radio.
- Disconnect outer end of window and tailgate gas struts. See
Rear window gas strut, removing and installing and Tail-
gate gas strut, removing and installing.
WARNING-
The tailgate is very heaq and will close without both pressu-
rized lifling struts installed. Properly support tailgate prior to
removal of the lifling struts.
- Remove trim panel from tailgate.

Downloaded from www.Manualslib.com manuals search engine
Trunk Lid, Tailgate I
4 Remove rubber grommet and applicable connectors. Discon-
nect rear window washer hose.
NOTE-
To facilitate installation, mark position of hinges for tailgate
and rear window frame on body
WARNING-
The tailgate is very heavy and will close without both pres-
surized lifting struts installed. Properly support tailgate pri-
or to removal of the lifting struts.
There is risk of fingers being trapped once tailgate fas-
teners are removed.
CAUTION-
Protect body opening for tailgate with fabric tape.
4 Remove hinge fasteners for tailgate and rear window frame.
Lower tailgate so that hinge for tailgate and rear window
can be tilted.
- Tilt hinge for tailgate and rear window frame so that tailgate
can be moved towards the rear with rear window frame.
- Remove tailgate with rear window frame towards rear.
- Installation is the reverse of removal
Rear window, removing and installing
- Disconnect electrical harnesses.
- Support window in open position.
Loosen fasteners on each window hinge.
NOTE-
Note positions of any spacers for reinstallation
CAUTION-
Rear window is heavy Use a second person to support win-
dow prior to releasing from hinges.
- Remove window hinge fasteners and lift off window.
- Installation is reverse of removal. Replace waterprooiing
sheeting where disturbed.
See Rear window and tailgate, alignment.

Downloaded from www.Manualslib.com manuals search engine
51 0 Exterior Trim. Bumpers
General ........................... .51 0.2 Exterior Trim ...................... 51 0-1 3
Outside Rear View Mirrors
Outside mirror glass. replacing
Outside mirror housing.
removing and installing
......
Outside mirror assemblv .
BMW emblem. removing and installing ... 510-13 .......... .51 0.2
Body side molding. replacing ........... 51 0-13 .......... .51 0.2
Radiator grill. removing and installing .... 51 0-1 4
Headlight housing trim panel.
.......... .51 0.3
removing and installing ............... 510-14 . .
removing and installing ................ .51 0.4
Bumpers ......................... .51 0.5
Front bumper assembly
............... .51 0.6
Front bumper, removing and installing
.... .51 0.7
Front bumper impact absorber. replacing
. .51 0.8
Rear bumper assembly ............... .51 0.9
Rear bumper. removing and installing
... .51 0.10
Rear bumper impact absorber. replacing
. .51 0.1 1
Front bumper height. adjusting
......... .51 0.12

Downloaded from www.Manualslib.com manuals search engine
-.- -
Exterior Trim, Bumpers
Outside mirror glass with automatic dip control,
replacing
4 Slide locking pin (arrow) right to release glass (A).
- If equipped with heated mirrors: remove heating element har-
ness connectors from
back of mirror glass.
4 Install mirror glass by placing glass on lugs (arrows) and turn
loclting pin until glass is locked in place.
Outside mirror housing, removing and
installing
- Remove mirror glass as described above.
4 Compress plastic retainers (arrows)
NOTE-
The front mirror housing is retained by either three or four
clips, depending on model.

Downloaded from www.Manualslib.com manuals search engine
51 0-4
I Exterior Trim. Bumpers
4 Carefully remove mirror housing from frame
- Installation is reverse of removal.
NOTE-
Check mirror function before installing covering parts
Outside mirror assembly, removing and
installing
- Remove front door panel trim. See 41 1 Doors
4 Carefully lift inner trim panel up to remove from retaining clip
(arrow).
Disconnect electrical harness connectors for window anti-
trapping protection (B) and speaker (A), if equipped.