Chain BMW 528i 2000 E39 Repair Manual

Downloaded from www.Manualslib.com manuals search engine
116-12
I Cylinder Head and Valvetrain
Camshaft and lifter removal and installation
(M52 engine)
Camshafts and lifters, removing (M52 engine)
WARNING
-
The process of evenly loosening the camshaft bearing cap
nuts is NOT an acceptable method of removing the cam-
shafts. Special tools should always be used to remove the
camshafts. Be sure to read the procedure
tlirough before
starting a job.
I Allow engine to cool before beginning this procedure. /
- Disconnect negative (-) cable from battery.
CAUTION-
Prior to disconnecting the batfew read the battery discon-
nection cautions given in
001 General Cautions and
Warnings.
- Remove VANOS control unit from cylinder head. See 117
Camshaft Timing Chain.
I I 4 Remove loosened bolts (arrows) from front of exhaust
sprocket
nuts
(arrows) from intake camshaft

Downloaded from www.Manualslib.com manuals search engine
Cylinder Head and Valvetrain
I I < Remove outer thrust washer, sprinq plate, and inner thrust
washer.
4 Remove both camshait sprockets with secondary timing
chain.
NOTE-
Keep chain and sprockets together as an assembly for easier
installation.
< Remove thrust washer studs (arrows) and remove thrust
washer.

Downloaded from www.Manualslib.com manuals search engine
116-14
I Cylinder Head and Valvetrain
4 Remove sensor gear (arrow).
Remove secondary timing chain tensioner retaining bolts
(arrows) and remove tensioner.
Remove timing chain guide
reta~ning bolts (arrows) and
remove guide.

Downloaded from www.Manualslib.com manuals search engine
116-15
Cylinder Head and Valvetrain
4 Remove primary timing chain tensioner plug (arrow) and pri-
mary tensioner.
CAUTION-
Primary timinq chain tensioner is under sarina aressure.
4 Remove primary timing chain sprocket and timing chain from
exhaust camshaft.
- Remove crankshaft locking tool (BMW 11 2 300) from
flywheel (installed during
VANOS removal).
Lift timing chain (holding under tension) and rotate engine
counterclockwise 30" from
TDC.
- Suspend timing chain with mechanic's wire

Downloaded from www.Manualslib.com manuals search engine
Cylinder Head and valvetrain1
- Remainder of installation is reverse of removal, noting the
following:
See
117 Camshaft Timing Chain for VANOS control unit
installation.
Tightening torques
Camshaft bearing caps
to cylinder head (M7) 15 Nm (1 1 ft-lb)
Cylinder head cover to cylinder head (M6) 10 Nm (89 in-lb)
Sparic plugs (M12) 23 Nm (17 ft-lb)
Camshaft and lifter, removal and
installation
(M52 TU and M54 engine)
Camshafts and lifters, removing
(M52 TU and M54 engine)
WARNING-
Allow engine fo cool before beginning this procedure.
- Disconnect negative (-) cable from battery.
CAUTION--
Prior to disconnecting the battea read the battery discon-
nection cautions in
001 General Cautions and Warnings.
Remove VANOS control unit. See 117 Camshaii Timing
Chain.
Remove primary timing chain tensioner (arrow).
CAUTION-
Primary timing chain tensioner is under spring pressure. 1

Downloaded from www.Manualslib.com manuals search engine
/Cylinder Head and Valvetrain
Press down on secondary chain tensionerand loclc into place
using
BMW special tool 11 3 292, or a thin drift or pin.
4 Remove exhaust camshaft impulse wheel mounting nuts
(arrows). Remove impulse wheel (A).
< Remove spring plate (A).
4 Remove intake camshaft sprocket mounting nuts (arrows)
and remove spring plate (labelled
FRONT).

Downloaded from www.Manualslib.com manuals search engine
I_
-.
Cylinder Head and Valvetrain
Remove torx
(arrows). screws
from
exhausl
: camshaft : sprocket
Lift off exhaust and intalte sprockets together with secondary
chain, thrust spacer
(A) from exhaust camshaft, and splined
shaft (B) from intake camshaft.
CAUTIOf+
Splined shafts share the same part number for both intake
and exhaust camshafts. Used splined shafts must be rein-
stalled in their
oriqinal locations.
Place intalte and exhaust sprockets in
BMW special tool 11 6
/ 180. Position spline gap on intake sprocket (arrow) as
shown.
4 Remove exhaust camshaft splined sleeve (A) and shaft (B).

Downloaded from www.Manualslib.com manuals search engine
11 6-22
Cylinder Head and Valvetrain
Remove secondary chain tensioner mounting bolts (arrows)
and remove tensioner with locking tool in place.
Remove primary chain sprocket mounting studs
(arrows) on
exhaust camshaft.
NOTE-
Counterhold camshafts when loosening.
Lifl primary chain sprocket off exhaust camshaft. Remove
sprocket from chain.

Downloaded from www.Manualslib.com manuals search engine
11 6-23
Cylinder Head and Valvetrain
Place timing
chain on end of exhaust camshaft
4 Do not remove end spline retaining screws from camshafts
(arrows).
CAUTION-
The end spline retaining screws precisely locate the end
splines to the camshafts. Do not loosen these screws.
Remove locating studs (arrows) from
intake camshaft. Lift
off intake
camshaft thrust spacer (A) and impulse wheel (B)
4 Remove cylinder head cover mounting studs (arrows) from
center of cylinder head.
- Remove crankshaft locking tool (BMW special tool 11 2 300)
from cranltcase.

Downloaded from www.Manualslib.com manuals search engine
..--.
I Cylinder Head and Valvetrain - I
4 Lift primary chain and hold under tension, rotate engine
against direction of rotation (counterclockwise) approximate-
ly 30".
To prevent damaging valves while
worlcing on camshafts, no
aistons should be in the TDC position.
- Remove BMW special tool set 1 I 3 240 from rear of cylinder
head.
Remove retaining nuts (arrows) and bearing cap
1 of intake
camshaft.
Intake camshaft bearing cap
1 is centered with adapter
sleeves. To avoid camshaft damage, it must be removed be-
fore anv other caos.
4 Fit BMW special tools 11 3 260 (A) and 11 3 270 (B) to cylin-
der head and screw long bolts (aiiows) into spark plug
threads. Tensioners will align with the bearing caps on the in-
take camshaft.
CA UTION--
Do not over torque bolts into spark plug holes. 1
4 Turn eccentric shaft of special tool to pretension intake carn-
shaft bearing caps. Remove nuts on remaining bearing caps.
- Slowly release tension on eccentric shaft and remove BMW
special tools. Remove bearing caps and set aside in order.
Remove camshaft and store safely.
CA U TIOW-
Camshaft bearing caps must be installed in their original lo-
cations.