clutch BMW 7 SERIES 1986 E23 Cruise Control With Electric Acutator

CRUISE CONTROL WITH ELECTRIC ACTUATOR

The electric actuator type cruise control system was intro-

duced on the BMW 733i and 528e models in 1982. From 1983 all

six-cylinder models will use this type.

The system is designed to operate at between 20 and approximately

90 mph. An electronic control unit (E.C.U.) controls an

electric actuator which maintains the desired road speed via

the throttle linkage.

Driver control is through a three-function switch operated by

a lever mounted on the right side of the steering column be-

hind the wiper lever.

Pushing the lever forward in the CONST position engages the

system and the car will accelerate until the lever is re-

leased. The E.C.U. contains a memory circuit which will hold

the speed that exists when the lever is released from the

CONST. position. Momentary operation of the lever in the CONST.

position will also cause engagement and lock the prevailing

speed into the memory.

Cruise control may be disengaged in any of five different

ways; momentarily moving the control switch up or down to OFF,

applying the foot brake, shifting the automatic transmission to

neutral, depressing the clutch, or whenever the actual speed

drops more than 15 mph below the memory speed.

Following disengagement, the car can be returned to the pre-

viously selected speed by pulling the control lever to RESUME.

The memory circuits in the E.C.U. are reset whenever the

lever is moved to CONST, but the only time the memory is cleared

is when ignition is turned off.

The E.C.U. receives a processed signal from the electronic

speedometer, which is equivalent to actual road speed. Con-

sequently, speedometer problems will affect cruise control.

ACTUATOR

CLUTCH SWITCH
BRAKE SWITCH

CRUISE CONTROL SCHEMATIC

(ELECTRIC ACTUATOR)
OFF

61-09/1
CABLE

GAS LINKAGE

BRIDGE

(AUTOMATIC)

ECU

SPEEDO

OFF

REED SWITCH

RESUME
CONST.
R

N

D
2
1

P

Test at ECU Plug

Component/Circuit
Result

4. Ignition on—check volt-

age at Terminal #5.
Control switch RESUME.
Move lever to RESUME.

Voltage jumps 0 to 12V.

If not, check wiring and

switch.

5. Measure resistance Term-

inal #3 to ground. (Auto

transmission in neutral.)

(Ignition off.)
A.) Automatic Trans-

mission

B.) Manual Trans-

mission
A.) Approximately 4

B.) < 1

6. Apply voltage to term.

#8 and ground term. #9.
Actuator solenoid

(Clutch)
Listen for click in actuator

7. Measure resistance

Terminal #8 to ground.
Actuator and clutch

switch.
Resistance approx. 30

Press clutch pedal, then

resistance = oo

If not, check wiring, clutch

switch, and brake lights.

8. Apply voltage to term.

#13 and ground term. #25.
Actuator motor

Listen for motor running.

9. Measure resistance

Terminal #24 to Terminal

#23.
Actuator potentiometer.

Resistance approx. 3000

If not, check wiring/

replace actuator.

10. Measure resistance

Terminal #23 to ground.
Ground
Resistance = 0

If not, check wiring and

ground.

11. Measure resistance

Terminal #26 to ground.
Actuator.
Resistance approx. 3000

If not, check wiring/

replace actuator.

12. Measure voltage at

term. #9 (Ignition on)
Brake light switch
0 Volts then depress brake

pedal voltage = 12V.

61-09/3

FOR CRUISE CONTROL TO BE ENGAGED

PIN 9 MUST SENSE GROUND THROUGH

STOPLIGHTS.

WHEN BRAKE SWITCH IS CLOSED OR

CLUTCH SWITCH IS OPEN, GROUND IS

ELECTRONICALLY REMOVED.

CRUISE CONTROL ELECTRICAL SCHEMATIC
BRAKE

SWITCH

CLOSED WITH BRAKE

PEDAL DEPRESSED
POWER

DISTRIBUTION

BOX

CLUTCH

SWITCH

OPENS WHEN

CLUTCH PEDAL

IS DEPRESSED
POWER

DISTRIBUTION

BOX

AUTOMATIC

TRANSMISSION

RANGE SWITCH
AUTOMATIC TRANSMISSION

CRUISE

CONTROL

SWITCH

C210

CRUISE CONTROL

CONTROL UNIT

TRANSMISSION

RANGE

DISPLAY

TO THROTTLE

VALVE
FEEDBACK

POTENTIOMETER
INSTRUMENT

CLUSTER

CRUISE

CONTROL

ACTUATOR

CLUTCH

SOLENOID
CANCEL RESUME ACCELERATE/

SPEED SET SPEED

CONTROL INPUTS
INSTRUMENT

CLUSTER

MANUAL

TRANSMISSION
IDLE

SPEED

CONTROL
FUSE 6

8 AMP

POWER

DISTRIBUTION
POWER

DISTRIBUTION

ACCELERATE/

SET
OFF RESUME
OFF
S217 C206 S309 C301
.75 GN/WT

.5 VI/WT C210 GN/WT

CLUTCH CONTROL CONTROL MOTOR CRUISE

OUTPUT OUTPUT ENABLE

SEE DASH LIGHTS
GROUND
"N"

OUTPUT

BAND
1.5 GN/WT

1 GN/WT
11

1 GN/WT
.75 GN/WT

.75 GN/WT
1

.75 8U/3R

.75 BU/BR
S234
3

15

1

2

D

6
N
R
P

S
W
0

GN
BU

.5 YL
.5 GN

.5 BU

4
5
SPEEDOMETER

SOLID STATE

2

C8

.5 BU/YL
CRUISE CONTROL

CONTROL UNIT

POWER INPUT
.5 VI/WT
C250

STOP LIGHTS
.5 GN/RD

.5 GN/RD
MANUAL

TRANSMISSION
AUTOMATIC

TRANSMISSION
C208

.5 GN/RD
C208
61-09/5

S224
.5 GN/RD
.5 GN/RD
9

G200
.5 BR
SPEEDOMETER
.5 VI/WT
1.5 VI/WT

S241
FUSE 12

8 AMP

.5 VI/WT

VEHICLE SPEED

INPUT

CRUISE

ENABLE

.75

BU/BR

C8
GROUND
FEEDBACK

REFERENCE
FEEDBACK

INPUT
SOLID STATE

24

26

.5 GY/RD
.5 GN/YL

4

.5 RD
7

.5 YL

.5 BR

3

S233
(-)

12

16

C1
C6
.5 BR

.5 BR

G200
.5 BR
.75 BU/BR

6

7
.75 BU/BR

.5 BU
C209
.5 BU/WT

2
3

G200
13

.5 BK

5

.5 BK
.5 GN
.5 WT

.5 WT
CONTROL

MOTOR
1