radiator BMW 745i 2002 E65 N62B44 Engine Workshop Manual
[x] Cancel search | Manufacturer: BMW, Model Year: 2002, Model line: 745i, Model: BMW 745i 2002 E65Pages: 55, PDF Size: 1.05 MB
Page 2 of 55
Downloaded from www.Manualslib.com manuals search engine SubjectPage
Components
Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
- Coolant Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
- Water Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
- Map-Controlled Thermostat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
- Cooling Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
- Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
- Expansion Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
- Transmission Oil/Water Heat Exchanger . . . . . . . . . . . . . . . . . . . . . . . . .44
- Electrically-Operated Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
- Viscous Coupling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Engine block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
- Oil Sump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
- Crankcase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
- Crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
- Connecting Rods and Pistons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
- Flywheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
- Vibration Damper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Lubrication System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
- Oil Jets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
- Oil Check Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
- Oil Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
- Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
- Pressure Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
- Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Review Questions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Page 40 of 55
Downloaded from www.Manualslib.com manuals search engine 38
N62 Engine
Cooling System
Coolant Circuit - 14 Liter Coolant Capacity
42-02-56
Cooling System (Circuit Flow)
1. Cylinder Head Bank 5-8 12. Radiator
2. Coolant Supply (heater core) 13. Radiator Partition (low temp section)
3. Water valve with electric water pump 14. Temperature Sensor
4. Cylinder Head Gasket 15. Water Pump
5. Coolant Supply Line 16. Radiator Return Flow
6. Cylinder Head Ventilation Lines 17. Radiator Ventilation Line
7. Hole (crankcase venting system) 18. Expansion Tank
8. Transmission oil lines 19. Thermostat
9. Oil/water heater exchanger for automatic transmission 20. Cylinder Head Bank 1-4
10. Thermostat for transmission oil heat exchanger 21. Vehicle Heater
11. Alternator Housing 22. Radiator (High Temperature Area)
Page 41 of 55
Downloaded from www.Manualslib.com manuals search engine 39
N62 Engine
Coolant Circuit
The coolant flow has been optimized allowing the engine to warm up as quickly as possi-
ble after a cold start as well as even and sufficient engine cooling while the engine is run-
ning. The cylinder heads are supplied with coolant in a cross-flow pattern. This ensures
more even temperature distribution to all cylinders. The cooling system ventilation has been
improved and is enhanced by using ventilation ports in the cylinder heads and in the radi-
ator. The air in the cooling system accumulates in the expansion tank. When a pressure of
2 bar is reached in the expansion tank, the air is bled out by the pressure relief valve in the
reservoir cap.
N No
ot
te
e:
:
The ventilation ports in the front of the cylinder heads provide quicker “self bleeding”
during a routine coolant exchange. The complex cooling system and the small ventilation
ports require that time should be allowed after the cooling system has been filled for the air
to escape.
Coolant flow in the Engine Block
The coolant flows from the water pump through the feed pipe (1) in the engine's V and to
the rear of the engine block. This area has a cast aluminum cover (see following illustration).
From the rear of the engine, the coolant flows to the external cylinder walls and from there
into the cylinder heads.
The coolant then flows from the cylinder heads into the engine block V and through the
return connection (3) to the thermostat housing. When the coolant is cold it flows from the
thermostat (closed) directly into the water pump and back to the engine (recirculating for
faster warm up).
When the engine reaches operating tempera-
ture (85 ºC-110 ºC), the thermostat opens the
entire cooling circuit to include the radiator.
42-02-57
Engine Block Coolant Flow
1. Coolant from the water pump through the feed pipe
to the rear of the engine.
2. Coolant from the cylinder walls to the thermostat
housing.
3. Return connection to water pump/thermostat.
Page 42 of 55
Downloaded from www.Manualslib.com manuals search engine 40
N62 Engine
The coolant flows to the rear of the engine block, from there through the side channels to
the cylinder walls and then into the cylinder heads (lower left picture). The cast aluminum
cover at the rear of the engine block (with sealing bead) is shown on the lower right.
Water Pump/Thermostat Housing
The water pump is combined with the thermostat housing and is bolted to the timing case
lower section.
C Ca
au
ut
ti
io
on
n
d
du
ur
ri
in
ng
g
i
in
ns
st
ta
al
ll
la
at
ti
io
on
n
o
of
f
t
th
he
e
w
wa
at
te
er
r
p
pu
um
mp
p:
:
The impeller is made from reinforced plastic.
42-02-59
Water Pump / Thermostat Housing
1. Map-controlled themostat (radiator cool return flow).
2. Electrical connection for Thermostat Heating element.
3. Thermostat Mixing Chamber
4. Temperature Sensor (hot coolant from engine)
5. Radiator in-flow (hot coolant from engine)
6. Heat exchanger (transmission oil return flow)
7. Leakage Chamber (evaporation space)
8. Alternator in-flow (cool supply)
9. Water Pump
10. Expansion Tank Connection
Page 44 of 55
Downloaded from www.Manualslib.com manuals search engine 42
N62 Engine
Map-controlled Thermostat
The map-controlled thermostat allows the engine to be cooled relevant to operating con-
ditions. This reduces fuel consumption by approximately 1-6%. The electrical connections,
the design and the map-controlled thermostat response have been enhanced. The map-
controlled thermostat function is the same as previous engines (M62).
Cooling Module
The cooling module contains the following main cooling system components:
• Cooling radiator
• Air conditioning condenser
• Transmission oil/water heat exchanger
• Hydraulic fluid radiator
• Engine oil radiator
• Main electric fan
• Fan shroud for viscous coupling fan
All the components (with the exception of the transmission oil radiator) can be removed for
repairs without disassembling any other coolant circuit. All connections have been fitted
with the quick-release coupling which are used in current models.
Maped-Controlled Thermostat
1. Radiator Return Flow To Thermostat
2. Connection for Thermostat Heating Element
3. Temperature Sensor
4. Radiator in-flow (hot coolant from engine)
Page 45 of 55
Downloaded from www.Manualslib.com manuals search engine 43
N62 Engine
Cooling Radiator
The radiator is made from aluminum and is divided into a high-temperature section and a
low-temperature section by a partition wall (see coolant circuit diagram). The coolant first
flows into the high-temperature section and then back to the engine, cooled.
Some of the coolant flows through an opening in the radiator partition wall to the low-tem-
perature section where it is cooled further. The coolant then flows from the low-tempera-
ture section (when the ÖWT thermostat is open) into the oil/coolant heat exchanger.
Coolant Expansion Tank
The expansion tank is mounted on the right hand wheel housing (engine compartment).
N No
ot
te
e:
:
The expansion tank should never be filled above the Max marking. Excess coolant is
expelled by the pressure relief valve in the cap as it heats up. Avoid overfilling the expan-
sion tank because the cooling circuit design ensures very good “self bleeding”.
Cooling Components
1. Cooling Radiator 4. Engine oil/air heat exchanger connection
2. Expansion Tank (hot countries only)
3. Water Pump 5. Transmission oil/coolant heat exchanger
Page 46 of 55
Downloaded from www.Manualslib.com manuals search engine 44
N62 Engine
Transmission Oil/Coolant Heat Exchanger
The transmission oil/coolant heat exchanger ensures that the transmission oil is heated up
quickly and also that it is appropriately cooled. When the engine is cold, the transmission
oil/coolant heat exchanger thermostat switches into the engine's recirculated coolant cir-
cuit. This allows the transmission oil to heat up as quickly as possible (with the engine
coolant).
When the return flow water temperature reaches 82 ºC, the thermostat switches the trans-
mission oil/coolant heat exchanger to the low-temperature coolant radiator circuit (refer to
the cooling circuit diagram) to cool the transmission oil.
Electrically Operated Fan
The electric fan is integrated in the cooling module and is mounted directly in front of the
radiator. The speed is regulated by the ECM.
Viscous Coupling Fan
The viscous coupling fan is driven by the water pump. The noise output and the perfor-
mance of the fan coupling and the fan wheel have been optimized as compared with the
E38M62. The viscous coupling fan is used as the final level of cooling and switches on at
an air temperature of 92 ºC.
N No
ot
te
es
s:
:
Page 54 of 55
Downloaded from www.Manualslib.com manuals search engine 52
N62 Engine
Oil Cooling (if equipped)
An oil cooler is used in hot countries. The oil cooler is located in front of the radiator above
the A/C condenser. The engine oil flows from the oil pump through a channel in the
crankcase to a connection on the generator support. The generator support has an oil ther-
mostat. A wax element in the oil thermostat continuously opens the inflow to the oil cooler
when the oil temperature is between 100 ºC to 130 ºC.
Some of the engine oil always flows past the oil thermostat and through the engine with-
out being cooled, even when the oil thermostat is fully open. This ensures a minimum
amount of oil is supplied when the cooler is faulty. A modified generator support, without
connections for the oil thermostat, is fitted to vehicles which do not have an oil cooler.
Technical Data - Lubrication System
The recommended oil is BMW High Performance 5W-30 Synthetic Oil
* P/N 07 51 0 017 866
O Oi
il
l
C
Ca
ap
pa
ac
ci
it
ty
y
i
in
n
L
Li
it
te
er
rs
s
E
Ex
xp
pl
la
an
na
at
ti
io
on
n
8.0 Filling Capacity for Service with Oil Filter Change
O Oi
il
l
P
Pr
re
es
ss
su
ur
re
e
E
Ex
xp
pl
la
an
na
at
ti
io
on
n
1.0 Minimum Oil Pressure at 20ºC
4.0 - 8.0 Bar Maximum Oil Pressure at 20ºC
O Oi
il
l
D
De
el
li
iv
ve
er
ry
y
C
Ca
ap
pa
ac
ci
it
ty
y
E
Ex
xp
pl
la
an
na
at
ti
io
on
n
9-12 I/Min At Idle Speed (700 rpm) at 20ºC
50-55 I/Min At Maximum Engine Speed (6500 rpm) and 20ºC