coolant level BMW 745i 2005 E65 N62B44 Engine Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 41
N62 Engine
Leakage Restraint System in the Water Pump
The water pump has a leakage restraint system for the functional leakage from the pump
shaft piston ring type seal. The coolant which escapes through the pump shaft sliding ring
seal usually accumulates and evaporates through a hold in the leakage chamber (evapora-
tion area).
If the sliding ring seal is faulty, the leakage chamber fills
completely with coolant. Sliding ring seal leakages can
be detected by monitoring the fluid level in the leakage
chamber (inspection hole).
N No
ot
te
e:
:

In the past, fully functional water pumps were often replaced because the functional
sliding ring seal leakage which is necessary for water pump operation resulted in evapora-
tion residues being left on the external walls of the water pump.
The leakage restraint system has the advantage in that the coolant escaping from the slid-
ing ring seal (normal, functional leakage) evaporates without a trace and cannot be mis-
takenly identified as a water pump defect during visual inspections.
Timing Chain Cover Lower Section
The waterpump mounts to the lower section to
channel coolant to the engine block.
42-02-61 Water Pump
1. Impeller
2. Sliding Ring Seal
3. Leakage Chamber / Evaporation Space
4. Leakage Chamber Cover
5. Delivery from the sliding ring seal to the leakage chamber
6. Hub of pulley and viscous clutch
Timing Chain Cover Lower Section
1. Coolant to Engine
2. Rear Water Pump Housing in Lower Section
3. Mount for Drive Belt Tensioner Pulley
4. Crankshaft Radial Seal
42-02-62

Downloaded from www.Manualslib.com manuals search engine 44
N62 Engine
Transmission Oil/Coolant Heat Exchanger
The transmission oil/coolant heat exchanger ensures that the transmission oil is heated up
quickly and also that it is appropriately cooled. When the engine is cold, the transmission
oil/coolant heat exchanger thermostat switches into the engine's recirculated coolant cir-
cuit. This allows the transmission oil to heat up as quickly as possible (with the engine
coolant).
When the return flow water temperature reaches 82 ºC, the thermostat switches the trans-
mission oil/coolant heat exchanger to the low-temperature coolant radiator circuit (refer to
the cooling circuit diagram) to cool the transmission oil.
Electrically Operated Fan
The electric fan is integrated in the cooling module and is mounted directly in front of the
radiator. The speed is regulated by the ECM.
Viscous Coupling Fan
The viscous coupling fan is driven by the water pump. The noise output and the perfor-
mance of the fan coupling and the fan wheel have been optimized as compared with the
E38M62. The viscous coupling fan is used as the final level of cooling and switches on at
an air temperature of 92 ºC.
N No
ot
te
es
s:
:

Downloaded from www.Manualslib.com manuals search engine 45
N62 Engine
Engine Block
Oil Sump
The oil sump consists of two parts. The upper section of the oil sump is made from cast
aluminum and is sealed to the crankcase with a rubber-coated sheet steel gasket. This
section of the oil sump has a cross shaped cut out oil filter element recess. The upper sec-
tion of the oil sump is inter connected to the oil pump and is sealed with a sealing ring. The
double panel (noise insulation) lower section of the oil sump is flanged to the upper section
of the oil sump.
Crankcase
The crankcase has a one-piece “open deck” design and is made entirely from AluSil. The
cylinder walls are hardened using a specific procedure (exposure honing). Exposure hon-
ing involves treating the cylinders with a special “soft stripping”. This removes the aluminum
from the cylinder surface and the hard silicone particles remain.
O Op
pe
en
n
D
De
ec
ck
k
=
=
E
Ex
xp
po
os
se
ed
d
c
cy
yl
li
in
nd
de
er
r
c
co
oo
ol
la
an
nt
t
c
ch
ha
am
mb
be
er
r








1. Flow to engine “V” (return coolant collection area) 2. External cylinder bank wall
Oil Sump Components
1. Upper Section of The Oil Sump
2. Oil Pump
3. Oil Level / Condition Sensor
4. Lower Section of The Oil Sump
5. Oil Filter Housing
6. Oil Drain Plug
42-03-65
42-03-66 42-02-67