ABS BMW 745LI 2007 E66 Level Control System Manual

8
Level Control Systems
Pressure Reservoirs
The oil pressure reservoirs (2) on each strut incorporate a membrane and are nitrogen gas
filled. They are designed to absorb the oil which is expelled from the struts during down-
ward movement, the gas in the reservoirs is compressed and pushes the oil back into the
struts during upward movement.
Gas Chamber
Membrane
Oil Chamber

13
Level Control Systems
Air Suspension Systems (EHC)
Purpose of the System
Air Suspension systems were first introduced on the 1999 E39 Sportwagon. Since then
the E53 (X5) and E65/E66 (7Series) models were available with this new system. EHC are
available is two configurations, the Single Axle Air Suspension System and the Dual Axle
Air Suspension System. The Dual Axle (EHC II) system is only available on E53 X5 models
from the 2002 model year.
EHC systems can be found on the following vehicles:
 E39 Sportwagon 528i, 525i and 540i from the 1999 Model Year (Single Axle)
 E53 X5 3.0i and 4.4i from the 2000 Model Year (Single Axle)
 E53 X5 4.6iS from 2002 (Single Axle)
 E53 X5 3.0i and 4.4i from 2002 (Dual Axle EHC II)
 E65/E66 from 2003 Model Year (Single Axle)
There are some functional changes with these systems. On EHC, the entire axle load is
borne by the air suspension. The underlying control philosophy of EHC is “Control only
when absolutely necessary”. This means that brief changes in the ride height are not com-
pensated (such as potholes). This avoids any unnecessary control operations.
The advantages of air suspension are as follows:
 Control is independent of the vehicle engine
 Single-wheel control is possible
 Lateral locking is affected
 A distinction is made between load and drive states
 An inclined load is identified and corrected
 However, an inclination is not compensated
 Self diagnosis can be performed
 Diagnosis with DISplus or GT-1 is possible
 An automatic interruption of control takes place in case of cornering and wheel
changes.

29
Level Control Systems
Pneumatic Drain Valve
The Pneumatic Drain Valve is activated pneumatically by pressure from the control valve.
This causes the drain valve to open allowing the pressure supply line to vent to atmosphere.
This design allows for large air volumes to be discharged quickly and eliminates the need
for a solenoid valve with high current consumption.
The 21 bar pressure limiting valve is integrated in the drain valve.
Electric Pressure Relief Valve
The electrically activated pressure relief valve controls normal system pressure. The con-
trol valve performs this function in conjunction with the drain valve.
HIgh Pressure Vent Valve
The High Pressure Vent Valve serves as a comfort valve and is used to release system pres-
sure after the accumulator has closed and the compressor is still running. When the high
pressure vent valve has opened the compressor can be stopped quietly.
Air Drier
In the air drier, the air which is drawn in passes over a water absorptive filter material in the
form of filter nodules which extract moisture from the air. As long as the air contains more
moisture than the filter material, the individual nodules absorb and accumulate the mois-
ture. When the air flows back, it is drier than the filter material, with the result that the air is
re-humidified and the moisture is discharged into the open air. The maximum
water storage capacity of the filter is 30 g.
1. Pneumatic Drain Valve
2. Electric Pilot Control Valve
3. High Pressure Vent Valve
4. Air Drier
5. Compressor
6. Sintered filter
7. To Pressure Accumulator/Valve Unit NW Size of
opening/tubing in mm.
Air Supply Unit

33
Level Control Systems
Air Suspension Strut
Rear
Minor modifications were made to the rear axle air springs. The air springs and the dampers
are configured separately at the rear axle.
Front
The air suspension replaces the steel suspension at the front axle, i.e. the spring bellows is
attached to the damper. The front air suspension strut and the impact absorber form a
complete unit.
Control Unit
The EHC2 Control Unit is located behind the glovebox adjacent to the General Module.
The connector is a black 54 pin connector.
Inputs received directly into the control unit are:
Ride Height Level Sensor (X4) Up and Down requests from the switch assy.
General Module (Load cutout signal) CAN Bus Inputs
K Bus Inputs Pressure Sensor
Compressor Temperature
O Ou
ut
tp
pu
ut
ts
s
i
in
nc
cl
lu
ud
de
e:
:
Air Unit Control (Activation) Front and Rear Axle Valves
LED’s for Switch Unit Compressor Relay
Pressure Accumulator
Air Suspension Strut
1. Auxiliary Spring
2. Air Bellows
3. Damper