BMW 750IL 1992 E32 Level Control System Manual

11
Level Control Systems
LAD Module
With a high pressure applied to the control piston,
the flow resistance is high and the damping force
will be stiff.
The load dependent module is a control valve
that regulates the flow of oil between the strut
and the pressure reservoir.
The control piston in the (LAD) moves in rela-
tion to the pressure applied from the pump.
This movement will regulate the tension on the
inner spring of the module. With only a low
pressure applied, a small amount of tension
will be applied to the spring. Little flow resis-
tance will be developed between the strut and
pressure reservoir. The damping force is soft.

12
Level Control Systems
Camber Warning Switch (E32 AND E34 Touring)
The self-leveling suspension systems used in the E32 and the E34 Touring are equipped
with a camber warning switch. The switch is mounted on the right rear axle support and
connected through a rod to the semi-trailing arm.
The function of the switch is to warn the driver of an
overload condition or an unsafe driving situation.
If the switch detects a rear wheel camber of -3.5 deg.
A signal is sent to the check control module and dis-
played on the dash.
A time delay of 8 minutes is incorporated to prevent
the warning from being displayed while driving
through turns.
The E38 does not use the camber warning switch
due to the design of the rear suspension.

13
Level Control Systems
Air Suspension Systems (EHC)
Purpose of the System
Air Suspension systems were first introduced on the 1999 E39 Sportwagon. Since then
the E53 (X5) and E65/E66 (7Series) models were available with this new system. EHC are
available is two configurations, the Single Axle Air Suspension System and the Dual Axle
Air Suspension System. The Dual Axle (EHC II) system is only available on E53 X5 models
from the 2002 model year.
EHC systems can be found on the following vehicles:
 E39 Sportwagon 528i, 525i and 540i from the 1999 Model Year (Single Axle)
 E53 X5 3.0i and 4.4i from the 2000 Model Year (Single Axle)
 E53 X5 4.6iS from 2002 (Single Axle)
 E53 X5 3.0i and 4.4i from 2002 (Dual Axle EHC II)
 E65/E66 from 2003 Model Year (Single Axle)
There are some functional changes with these systems. On EHC, the entire axle load is
borne by the air suspension. The underlying control philosophy of EHC is “Control only
when absolutely necessary”. This means that brief changes in the ride height are not com-
pensated (such as potholes). This avoids any unnecessary control operations.
The advantages of air suspension are as follows:
 Control is independent of the vehicle engine
 Single-wheel control is possible
 Lateral locking is affected
 A distinction is made between load and drive states
 An inclined load is identified and corrected
 However, an inclination is not compensated
 Self diagnosis can be performed
 Diagnosis with DISplus or GT-1 is possible
 An automatic interruption of control takes place in case of cornering and wheel
changes.

14
Level Control Systems
EHC System Overview
EHC I Single Axle Air Suspension E39/E53
EHC II Dual Axle Air Suspension E53
1. Air Supply Unit
2. Rear Axle Air Bellows
3. Ride Height Sensors
4. Pressure Accumulator/
Valve Unit
5. Front Axle Air Bellows
6. Control Unit

15
Level Control Systems
Single Axle EHC I System Components (E39/E53)
The EHC system consists of the following components:
 EHC Control Module
 Air Springs (2) with Air Reservoirs
 Rear Axle Level Sensors
 Encapsulated Air Supply (LVA)
 Warning Indicator
Control Module
The Control Module is mounted in the module carrier box in the luggage compartment on
the right side. It contains the processing electronics and final stages for operation of the
EHC system.
The control module receives the following inputs for its processing functions:
 KL 30 & 31 (Power/Ground)
 KL 15
 Left & Right Ride Height Sensors
 K Bus for;
- Vehicle speed
- Engine running
- Door/tailgate - open/closed
E39 Features 06
EHC Module (E39)

16
Level Control Systems
The control module incorporates two filters (slow/rapid) for processing the input signals
from the ride height sensors. Depending on the operating mode, either the slow or rapid fil-
ter is used to check the need for a regulating sequence.
The slow filter is used during the normal operation mode to prevent normal suspension trav-
el from causing the system to make adjustments.
The rapid filter is used during the pre-run and tailgate (LID) modes to ensure that the sus-
pension is adjusted quickly while the vehicle is being loaded or checked prior to operation.

17
Level Control Systems
Air Springs
The air spring is made from a flexible rubber material. It
forms an air tight cavity which provides the calculated
spring rate required for the sport wagon.
As the spring compresses downward the bottom edge
of the rubber material rolls along the vertical surface of
the base mount cylinder.
Air is added or removed from the air spring through its
top port. The top port of each spring is connected to a
reservoir and the air supply pipes. The reservoirs are
required to hold additional air due to the compact design
of the springs.
Rear Axle Level Sensors
Hall effect sensors are mounted on the left
and right sides of the rear suspension for
ride height detection. They are pivoted by a
coupling rod through the rear axle swing
arms.
The hall sensors produce a varying voltage
input to the control module as the suspen-
sion height changes.
If the vehicle is equipped with Xenon head-
lights the right side sensor contains an
additional sensor for the automatic head-
light level adjustment system.
Warning Displays
If the system is faulted and off-line or set in the transport mode, the following is displayed:
Basic Cluster:A warning lamp indicator is illuminated used on the basic cluster.
High Cluster: A message is posted in the high cluster matrix display.
E39 Features 07

18
Level Control Systems
Air Supply System (LVA)
The air supply system is identified as the LVA in the diagnosis program and in the repair
manual. It is mounted in the spare tire well compartment. The components are housed in
a sound deadening carrier, through rubber bushings, to prevent operating noises from
being transmitted through the vehicle’s interior.
With the exception of the compressor relay, individual replacement parts for the air supply
system are not available. If diagnosis determines a defect in any of the other air system
components, complete replacement is necessary.
The air supply system consists of the following components:
 Compressor assembly with;
- Piston compressor
- Electric motor
- Air dryer (desiccator)
- Pressure relief solenoid valve
- Pressure maintenance valve
- Check valves
 Compressor Relay (Replaceable)
 Solenoid Valve Block (2 - two way
valves)
 Lines - including distributor
E39 Features 05

19
Level Control Systems
Air Supply System (LVA) Operation
The single stage piston compressor produces a maximum pressure of 13.5 Bar. The com-
pressor is maintenance free - provided it is used in a dust free environment. This includes
the compressor’s intake air filter.
The compressor is driven by a DC motor that is controlled by the compressor relay through
the control module.
When the compressor is activated, the pressure builds up to a working pressure of 11.4
Bar (+0.8/-1.5 Bar). This is controlled through the pressure maintenance valve. The air
under pressure is fed through the dryer and check valve to the solenoid valve block for the
air springs.
There is one solenoid valve in the valve block for each air strut. This allows the system to
compensate for uneven loads in the vehicle and maintain the vehicles ride height at all
times.
Pressure is drained through the left or right solenoid valve (energized open) the pressure
relief solenoid valve, restrictor, check valve and dryer back to the inlet side of the compres-
sor pump.
LVA Location X5

20
Level Control Systems