change time BMW 760LI 2001 E66 Level Control System Manual

31
Level Control Systems
The pressure accumulator decreases the load on the compressor and significantly reduces
the time required for large changes in ride height.
The EHC 2 control module monitors system pressure via a pressure sensor mounted on
the accumulator. Normal system pressure is 15.7 +/- 0.7 bar. Minimum system pressure
is 9 bar.
The pressure accumulator's charge is sufficient to fill the four suspension struts once from
the Access position to the normal position and compensate for vehicle load up to maximum
gross weight.
Valve Unit
In the valve unit, four bellows valves and the pressure accumulator valve are activated.
The bellows valves and the pressure accumulator valve are solenoid valves which are
closed under spring pressure when de-energized.
Accumulator/Valve Unit
1. Air Lines
Yellow-Black Front
Red-Blue Rear
2. Pressure Accumulator
3. Connecting Cable
4. Pressure Sensor
5. Valve Unit
Valve Unit
1. Connections for Air Lines
2. Pressure Accumulator valve
Pneumatic Layout of Control Valve
1. Pressure Accumulator
2. Accumulator Pressure Sensor
3. Pressure Accumulator Valve
4. Bellows Valves
5. From the Air Supply Unit
NW Size of opening/tubing size in mm.

36
Level Control Systems
The various levels can be preselected while travelling. Changeover between ride levels is
effected at the speed threshold values defined in the control unit. The control unit monitors
the change-over.
As soon as the driver sets a new target ride level by pressing a button or when a change-
over is initiated automatically by a specific driving condition, the LED for the current ride
level remains lit and the LED for the target ride level begins to flash.
When the new level is reached, the LED for the previous level goes out and the LED for the
new level reached stays lit permanently.
If a ride level selection is not allowed, the LED indicating the momentary ride level of the
vehicle flashes for 3 seconds.
A special case is preselection of Access levels while travelling. The Access LED flashes and
the LED for the original ride level is lit permanently. However, this does not mean that a con-
trol operation has already begun. The control operation does not actually begin until the
speed threshold which the Access level allows is reached or undershot.
Off-Road
(+25 mm)
Standard
(0 mm)
Access
(-35 mm)
Up button
and
<50km/h
Up button
or
>35km/h Up button
or
60 s time period
Access
Preselection
<25km/h Down Button and
<80km/h
and
Accumulator pressure
>threshold
and/or
compressor temperature
Down button
or
>50km/h

37
Level Control Systems
In addition to the LED indicator, the following text messages can
be displayed in the instrument cluster:
T TR
RA
AI
IL
LE
ER
R
M
MO
OD
DE
E
A coupled trailer is identified via the trailer connector. To avoid damaging the trailer and
the vehicle, changes of vehicle level are generally avoided. The standard level is "frozen."
If the trailer is coupled at a level other than the Standard level, the vehicle ride level is
not changed to Standard unless a button is pressed or the speed threshold for auto-
matic change-over is reached. The standard level is then "frozen" until the trailer con-
nector is disconnected.
R RI
ID
DE
E
H
HE
EI
IG
GH
HT
T
C
CO
ON
NT
TR
RO
OL
L
I
IN
NA
AC
CT
TI
IV
VE
E
Faults in the system and on the control unit which are only identified by the instrument
cluster, e.g. control unit disconnected
R RI
ID
DE
E
H
HE
EI
IG
GH
HT
T
C
CO
ON
NT
TR
RO
OL
L
I
IN
NA
AC
CT
TI
IV
VE
E
+
+
M
MA
AX
X.
.
6
60
0
k
km
m/
/h
h
For safety-critical faults (vehicle is too high or at inclination)
Control Modes
Sleep mode
If the vehicle is parked, it enters Sleep mode after 16 minutes. No further control opera-
tions are executed. A "watch dog" wakes up the control unit for a few minutes every 6
hours (wakeup mode) in order to compensate for possible inclination of the vehicle. (Vehicle
height may only be corrected once as air supply unit only operates with engine running.)
Wake-up
In wake-up mode, the control unit is woken up for a set period of time in order to com-
pensate for possible inclination of the vehicle. Inclination of the vehicle can be caused by
large temperature differences or by minor leaks. Adjustments to the front and rear axles
ensure that the vehicle is visually level. To minimize power consumption, the vehicle is low-
ered only. The nominal level of the lowest wheel serves as the nominal level for all other
wheels. The lowest nominal level to which the vehicle is lowered is the Access level (-35
mm).
Exception:if the vehicle is parked at Access level, the vehicle is lowered to max. -50 mm
in wake-up mode. If the vehicle is parked for a prolonged period of time and there is a leak
in the system, further loss of pressure does not produce a change of ride level since the
weight of the body is born by the auxiliary suspension and the residual tire pressure.
Advance /Overrun
When the vehicle is woken out of sleep mode by the load-cutout signal (VA), it normally
enters advance / overrun mode. Since the engine is not (no longer) running in this mode,
however, there are restrictions on the control operations that can be performed in order to
conserve the battery. Ride level compensation is restricted to tolerance ranges of 20 mm
and 25 mm in the up and down directions respectively. This serves to reduce the frequen-
cy of control operations.

38
Level Control Systems
All control operations in advance / overrun mode are executed as long as pressure is avail-
able in the accumulator. When the accumulator is empty and the engine is turned off, con-
trol operations are directly driven by the compressor. User-activated changes of ride level
and filling of the accumulator are not possible.
Terminal 15
As soon as the ignition is turned on (terminal 15), the user is allowed to lower the ride level
as required.
However, it is still not possible to raise the ride level or fill the accumulator.
Ride level is compensated outside a narrow tolerance range of 10 mm upwards and 10 mm
downwards.
Engine "on"
Ride level compensation, raising and lowering the vehicle's ride height as well as filling the
accumulator are permitted when the engine is running. The compressor also starts up dur-
ing every control operation.
Ride level is still compensated outside the narrow tolerance range of ±10 mm.
As long as the vehicle is stationary, high speed filtered ride level signals are used to detect
a change of load. This allows the system to react immediately to changes in ride level.
As soon as the vehicle is travelling, it changes over to low speed filtered ride-level signals.
The system no longer reacts to bump movements caused by road surface unevenness. A
mean value is formed over a prolonged period of time, i.e. payload is only altered by the
progressive emptying of the fuel tank.
The high speed filter is not used until the vehicle is stationary again and a lid is opened. If
no lid is opened, the vehicle logically cannot be loaded or unloaded.
SleepWake-Up
Power Down
Watch Dog
Ignition “ON”Advance/
Overrun
VA = Load Cutout Signal
Sleep = Temporary Power Down of Control Unit
Wake-up = Activating the Control Unit
Watch Dog = Monitoring
Engine Off
Engine On
Engine Running
Terminal 15 “ON” VA up
VA Down
Terminal 15 “OFF”

49
Level Control Systems
Post Mode
The Post-mode is adopted in order to compensate any inclination or to adjust the ride
height after driving and between the Pre-mode and Sleep mode.
The Post-mode is limited in time to 1 minute. The Post-mode is only executed if the engine
has been running before the system switches into this mode. If the engine has not been
previously running, the system switches directly from Pre-mode into Sleep mode.
The control operation is performed in a narrow tolerance band of +/- 6mm and is terminat-
ed at +/- 4mm. The fast signal filter is used.
In the event of an inclination (Kerb Mode), the control operation takes place for the nominal
heights applicable in this situation.
Pre-Mode
The Pre-mode is activated by the “Load Cutoff” signal (e.g. by opening the door or unlock-
ing with the remote control). The Pre-mode then stays set for 16 minutes and is restarted
with a change in status.
The ride height of the vehicle is monitored and evaluated with a wide tolerance band.
In Pre-mode, the vehicle is only controlled un to the nominal height if the level is significantly
below the nominal height. The control tolerance band is -40mm from the mean value for
the single axle air suspension and -20mm for the dual axle system. This control tolerance
ensures that the vehicle is only controlled up in the case of large loads in order to increase
the ground clearance prior to departure. Small loads give rise to small compression travel
and this is compensated only when the engine is started. This control setting helps reduce
the battery load.
With the single axle air suspension, the vehicle is controlled down when the mean value
derived from both ride height signals is > 0mm and one side is in excess of +10mm. With
twin axle air suspension, the vehicle is controlled down when one side is >15mm.
In this mode, only the mean value of the two height signals is considered when deciding
whether there is an need for control operation.
The control operation is executed as long as pressure is available in the accumulator. When
the accumulator is empty and the engine is turned off, the control operation is driven direct-
ly by the compressor. User-activated changes of ride level and filling of the accumulator are
not possible.
Control operations which were started in other modes are continued with the inner toler-
ance bands applicable to these modes.
There is no inclination identification in Pre-mode.

50
Level Control Systems
Normal
The normal mode is the starting point for the vehicle’s normal operating state. It is obtained
by way of the engine running signal.
Ride level compensation, changing the vehicle’s ride height and filling the accumulator are
possible. The compressor starts up as required.
A narrower tolerance band than that in Pre-mode cab be used because the battery capac-
ity does not have to be protected. The fast filter is used with a narrow tolerance band of
+/- 10mm. In this way, ride level compensation takes place outside a narrow band of 10+/-
10mm. The faster filter allows the system to respond immediately to changes in ride level.
Evaluation and control are performed separately for each wheel.
When a speed signal is recognized, the control unit switches into Drive mode. When the
vehicle is stopped, the control unit remains in Drive mode. The system switches back into
Normal mode when a door or the boot (trunk) lid is also opened. If none of the doors or
the boot lid is opened, the vehicle cannot be loaded or unloaded.
This prevents a control operation happening when the vehicle (for example) is stopped at
traffic lights and the ride height is above the mean axle due to the pitching motion on the
rear axle.
Drive
The Drive mode is activated for E39/E53 single axle air suspension when a speed signal of
>4km/h is recognized. The Drive mode is recognized from >1km/h for the E65/E66 single
axle air suspension and for the E53 twin-axle air suspension system.
Low pass filters are used. In this way, only changes in ride height over a prolonged period
of time (1000 seconds) are corrected. These are merely the changes in ride height, caused
by vehicle compression and a reduction in vehicle mass due to fuel consumption. The high
pass (fast) filter is used during the control operation. The slow filters are recognized at the
end of the control operation. The slow filters are re-initialized at the end of the control oper-
ation. The markedly dynamic height signals caused by uneven road surfaces are filtered
out.

52
Level Control Systems
Lift
The Lift mode is used to prevent control operations when a wheel is changed or during
work on the vehicle while it is on a lifting platform.
This mode is recognized when the permitted rebound travel at one or more wheels is
exceeded. For the E65/E66 the limit is > 55mm.
A “jack” situation is also recognized when the ride level is stored and the lowering speed
drops below the value of 2 mm/s for 3 seconds.
If the vehicle has been raised slightly and the permitted rebound travel has not yet been
achieved, the control operation attempts to readjust the ride height. If the vehicle is not low-
ered, a car jack situation is recognized after a specific period of time and this ride height is
stored.
A reset is performed if the vehicle is again 10 mm below this stored ride height.
Transport
The Transport mode is set and cleared by means of a diagnosis activation. It serves to
increase the ground clearance in order to ensure a safe transportation of vehicles on trans-
porter trucks. The nominal height of the vehicle is raised in this mode by 30 mm.
When the Transport mode is activated, the air suspension symbol is indicated in the vari-
able telltale in the instrument cluster and a text message is output in the Check Control
Display.
Control operations do not take place in this mode because the vehicle mass does not
change during transportation.
Belt
The Belt mode is set for mounting on the belt in order to avoid control operations.
When the Belt mode is activated, the air suspension symbol is indicated in the variable tell-
tale in the instrument cluster and a text message is output in the Check Control display.
The Belt mode is cleared by means of a diagnostic activation only. The Belt mode can no
longer be set.
New control units are supplied with the Belt mode set.
Control operations are not performed, the safety concept only operates with limited effect.
The Belt Mode is also known as “Band Mode” or “Assembly Line Mode”.