headlamp BMW X3 3.0I 2004 E83 Owner's Manual
[x] Cancel search | Manufacturer: BMW, Model Year: 2004, Model line: X3 3.0I, Model: BMW X3 3.0I 2004 E83Pages: 132, PDF Size: 3.62 MB
Page 12 of 132
Cockpit
10
Cockpit
Controls
1
Parking lamps/low beams57
2
>
Turn signal indicators41
>
Standing lamps58
>
High beams58
>
Headlamp flasher41
>
Computer47
3
Fog lamps58
4
Horn
5
Washer/Wiper system/Rain sensor41
6
Hazard warning flashers
7
Central locking system18
8
Unlocking the engine hood92
Page 14 of 132
Cockpit
12
Indicator and warning
lamps
Technology that monitors itself
The indicator and warning lamps identified
by the
+ symbol are subjected to an oper-
ation check each time you switch on the
engine. They each light up once for differ-
ent periods of time.
When a malfunction occurs in a monitored
system, the corresponding lamp will either
fail to go out when the engine is started, or
it will come on again during normal driving.
Detailed information is provided on the
specified pages.
Please fasten safety belt
+ 30
Airbags
+ 54
Brake system
+
With handbrake released 52/ 96
With handbrake set 38
With other warning lamps 52
Brake warning lamp for Canadian
models
Driving stability control systems/
Antilock Brake System
+ 53
Antilock Brake System ABS/
Chassis control system for Cana-
dian models
Brake pads
+ 96
Dynamic Stability Control DSC/
xDrive
+ 50/ 52
Flat Tire Monitor
+ 53
Automatic transmission
+ 39
Engine oil + 94
Service Engine Soon
+ 98
Service Engine Soon
+ 37
warning lamp for Canadian
models.
Check Gas Cap
+
Engine electronics + 37
Battery charge current
+ 105
Topping up coolant 95
Topping up washer fluid 94
Lamp defective 57
Turn signal indicators 41
Fog lamps 58
Headlamp flasher 41
High beams 58
Cruise control 43
Page 43 of 132
Reference
At a glance
Controls
Driving tips
Mobility
41
appear briefly in the instrument cluster fol-
lowed by the current gear.
To obtain maximum acceleration, for
passing maneuvers, etc., during
operation in the manual mode, use the
kickdown or downshift manually.<
Shifting from M/S to the selector-lever
positions P, R and N is only possible by
going through D.
Possible displays
P R N D SD M1 M2 M3 M4 M5
Malfunctions
If the indicator lamp lights up, there
is a function fault in the transmis-
sion system.
While it will remain still possible to move
the selector lever to any desired position,
the transmission will revert to operation in
its default mode with only a limited number
of forward gears.
Avoid high loads and drive to the nearest
BMW Sports Activity Vehicle Center.
Never work in the engine compart-
ment with any of the forward or
reverse gears engaged, as the vehicle
could start to move.<
Information on jump-starting and towing
starts on page 108.
Turn signal indicators/
headlamp flasher
1High beams Ð blue indicator lamp
2Headlamp flasher Ð blue indicator lamp
3Turn signal indicators Ð green indicator
accompanied by periodic clicking
sound from the relay
If the flashing indicator lamp and the
clicking from the relay are both faster
than normal, this indicates that one of the
turn signal indicator bulbs is defective.<
Signaling briefly
Press the lever up to but not beyond the
resistance point. It then returns to the cen-
ter position when released.
Washer/wiper system/Rain
sensor*
0Wipers retracted
1Intermittent or rain sensor operation
2Normal wipe
3Fast wipe
4Brief wipe
Page 44 of 132
Driving
42 5Serrated dial for adjustment of the wipe
interval or the sensitivity of the rain sen-
sor
Retracted position
The right wiper is partially concealed by the
hood.
To move the wipers into a vertical position:
1.Switch on wipers in lever position 1
2.When the wipers are approximately
vertical, move the ignition key to
position 0.
For changing the wiper blades, refer to
page 99.
Fold the wipers back down onto the
windshield before you turn the igni-
tion key to position 1 or 2 again. If you do
not, they could be damaged.<
Intermittent mode
Not on vehicles with rain sensor.
You can set the wipe interval to four stages
with the serrated dial 5.
In addition, the wipe interval is varied auto-
matically depending on road speed.
Rain sensor*
The rain sensor is positioned on the wind-
shield, directly in front of the interior rear-
view mirror.
Deactivate the rain sensor when
passing through an automatic car
wash. Failure to do so could result in dam-
age caused by undesired wiper activa-
tion.<
Activating
>Move the lever to position 1 with the
ignition key in position 1 or higher. The
wipers travel once across the wind-
shield, regardless of the weather condi-
tions.
You can leave the lever permanently in
position 1 and then only need to activate
the rain sensor as of ignition key position 1.
To do so:
>Briefly turn the serrated dial 5 or>Cleaning windshield 1, refer to next
section.
Adjust sensitivity: turn the serrated dial 5.
Deactivating
>Move lever to position 0.
Normal wipe
The system switches automatically to inter-
mittent mode when the vehicle is not mov-
ing, not on vehicles with rain sensor.
Fast wipe
The wipers operate at normal speed when
the vehicle is not moving, not on vehicles
with rain sensor.
Cleaning windshield, rear window
and headlamps*
0Wipers retracted
1To clean windshield and headlamps
2Rear window wiper intermittent mode
3Clean the rear window
Do not use the washers if there is any
danger that the fluid will freeze on the
windshield. If you do so, your vision could
be obscured. To avoid freezing, use a
washer fluid antifreeze, refer to page 94.
Do not use the washers when the reservoir
is empty. This could cause damage to the
washer pump.<
Cleaning the windshield
The system sprays washer fluid against the
windshield and activates the wipers for a
brief period.
The windshield washer nozzles are auto-
Page 45 of 132
Reference
At a glance
Controls
Driving tips
Mobility
43
matically heated as of ignition key
position 2.
Cleaning headlamps*
When the vehicle lighting system is
switched on, the headlamps are cleaned at
regular and appropriate intervals.
Rear window wiper
Rear window wiper in intermittent mode.
When reverse gear is engaged, the wiper
operates continuously.
You can also program the interval:
1.Briefly move the wiper lever from posi-
tion 0 to position 2
2.Wait for desired interval; maximum of
30 seconds
3.Move the wiper lever from position 0 to
position 2 again
To change the wiper blades, refer to
page 99.
Cruise control*
The vehicle maintains and stores the speed
that you set as of a speed of approx.
20 mph/30 km/h.
You can use cruise control whenever the
system is active while the engine is run-
ning.
Indicator lamp
Indicator lamp in the instrument
cluster lights up green:
System ready for operation using
the buttons in the steering wheel.
Activating the system
From ignition key position 2:
Press button in steering wheel; the indica-
tor lamp in the instrument cluster comes
on. You are able to use the cruise control.
Do not use the cruise control when
driving on winding roads, in heavy
traffic or in poor road conditions Ð e.g. snow, rain, ice, loose road surface Ð that do
not permit a constant speed.<
Deactivating system
Press the button repeatedly until the indi-
cator lamp in the instrument cluster goes
out.
The cruise control is also deactivated when
the ignition key is turned to position 0. The
speed stored in the memory is deleted in
the process.
Maintaining and storing speed or
accelerating
Briefly press button +:
The system maintains and stores the cur-
rent vehicle speed. Every time you briefly
press the button, the vehicle's speed
increases by roughly 1Ðmph/1 km/h.
Press and hold button
+:
The vehicle accelerates without pressure
on the accelerator pedal. When you release
the button, the system maintains and
stores the current speed.
If, on a downhill gradient, the engine's
braking effect is not sufficient, the
controlled speed can be exceeded. Speed
can drop on uphill grades if the engine out-
put is insufficient.<
Decelerating
Briefly press button Ð:
Every time you briefly press the button,
the vehicle's speed decreases by roughly
1 mph/1 km/h if you are already driving
with cruise control.
Press and hold button
Ð:
With the cruise control active, the system
automatically reduces the throttle opening
to slow the vehicle. When you release the
button, the system maintains and stores
the current speed.
Page 59 of 132
Reference
At a glance
Controls
Driving tips
Mobility
57
Lamps
Parking lamps/low beams
Parking lamps
The front, rear and side vehicle
lighting is switched on. You can use
the parking lamps for parking. For
lighting on one side for parking as an addi-
tional feature, refer to page 58.
Low beams
When you switch on the ignition
with the headlamps on, the head-
lamps go out and only the parking
lamps remain on.
Lamp defective
The indicator lamp lights up:
At least one bulb of the exterior
lighting on the vehicle is defective.
Replacing the bulbs, refer to page 99.
Pathway lighting
When you activate the headlamp flasher
after parking the vehicle and switching off
the lamps, the low beams will come on for
a brief period.
You may also have this function deac-
tivated if you wish.<
Lights on warning
If you turn the ignition key to position 0, an
acoustic signal sounds when you open the
driver's door for a few seconds to remind
you that the light has not yet been switched
off
.
Daytime driving lamps*
You can leave the light switch in the second
position: all external lamps go out when
you switch off the ignition.
Always observe all applicable laws govern-
ing the use of daytime driving lamps.
You can switch on the parking lamps when
needed using the standard procedure
described under Parking lamps.
You can have the daytime driving
lamp circuit activated on your vehi-
cle.<
Automatic headlamp control*
When you set the switch to this
position, the system activates and
switches on and off the low beams
in response to changes in ambient light
conditions, for instance, in tunnels, at dawn
and dusk, and in rain and snow.
Following automatic activation the
vehicle's external lighting remains on
when you switch on the fog lamps.<
Automatic headlamp control cannot
serve as a substitute for the driver's
judgment in determining when the vehicle
lamps should be switched on. For example,
the system cannot detect fog. To avoid
safety risks, you should always switch on
the lamps manually under these condi-
tions.<
You can have the sensitivity of the
headlamp control adjusted.<
Adaptive Head Light*
The concept
Adaptive Head Light is a variable headlamp
control system that enables dynamic illumi-
nation of the road surface. Depending on
the steering angle and other assumptions,
the light from the headlamp follows the
course of the road.
Page 60 of 132
Lamps
58
Activating the Adaptive Head Light
In ignition key position 2, turn the
light switch to the position 'Auto-
matic headlamp control'.
When the vehicle is backing up, the
Adaptive Head Light is inactive; when
the vehicle is at a standstill, it is only active
in one direction.<
Malfunction
The LED above the symbol for automatic
headlamp control flashes. Please have it
checked by your BMW Sports Activity
Vehicle Center.
Instrument lighting
Turn the serrated dial to adjust the illumina-
tion intensity.
High beams/standing lamps
1High beams Ð blue indicator lamp
2Headlamp flasher Ð blue indicator lamp
3Standing lamps
Standing lamps, left or right*
You also enjoy the option of lighting up just
one side of your vehicle when parking.
When using this function, comply with
national regulations:
In ignition key position 0 or with ignition key
removed:
Allow the lever to engage in the corre-
sponding turn signal indicator position.
Fog lamps*
A green indicator lamp appears in
the instrument cluster to indicate
that the front fog lamps are on.
If the automatic headlamp control is
activated, the low beams will come on
automatically when you switch on the fog
lamps.<
Interior lamps
The interior lamps operate automatically.
If you desire, the interior lamps are
switched on after mechanical unlock-
ing of the vehicle. You may have this func-
tion activated/deactivated if you wish.<
Page 95 of 132
Reference
At a glance
Controls
Driving tips
Mobility
93
Engine compartment
1Reservoir for windshield and headlamp
washer system94
2Body ground Ð negative terminal108
3Auxiliary terminal for jump-starting108
4Engine oil filler neck95 5Brake fluid reservoir96
6Dipstick for engine oil94
7Coolant expansion tank96
Page 96 of 132
Under the engine hood
94
Washer fluid
Windshield and headlamp washer
system
Antifreeze agent for the washer sys-
tems is inflammable. For this reason,
keep it away from sources of flame and
store it only in its original containers. Store
it so that it is inaccessible to children.
Always observe the instructions for use
provided on the containers.<
We recommend that you mix the
washer ßuid before adding it to the
reservoir.<
Capacity:
approx. 6.9 US quarts/6.5 liters.
Fill with water and, if required, with an anti-
freeze additive according to manufac-
turer's recommendations.
Engine oil
Indicator lamp
Engine oil pressure
The indicator lamp lights up red:
Stop the vehicle immediately and
switch off the engine. Check the
engine oil level; top up as required. If the oil
level is correct: contact the nearest BMW
Sports Activity Vehicle Center.
Do not continue driving. The engine
could be damaged because of inade-
quate lubrication.<
Engine oil level
The indicator lamp lights up yellow
while driving:
The oil level is at the absolute mini-
mum. Add engine oil as soon as possible.
Until then, do not drive more than
approx. 30 miles/50 km.
The indicator lamp lights up yellow
after the engine is switched off:
Top up engine oil at the earliest
opportunity Ð when refueling.
Engine oil sensor
The indicator lamp lights up yellow
within 20 seconds after starting the
engine:
The oil level sensor is defective. Please
have it checked by a BMW Sports Activity
Vehicle Center.
Checking oil level
1.Park the vehicle on a level surface
2.Switch the engine off after it has
reached normal operating temperature
3.After approx. 5 minutes, pull the dip-
stick out and wipe it off with a clean lint-
free cloth, paper towel, or similar mate-
rial
4.Carefully push the dipstick all the way
into the guide tube and pull it out again
5.The oil should extend to between the
two marks on the dipstick.
As is the case with fuel economy, the rate
at which the engine uses oil is strongly
influenced by driving style and operating
conditions.
The oil quantity between the two marks of
the dipstick is approx. 1.1 US quarts/1 liter.
Page 102 of 132
Replacing components
100 When maintaining the headlamps,
please comply with the instructions in
the separate Caring for your vehicle bro-
chure.<
Halogen low beams
H7 bulb, 55 Watts
Always wear gloves and eye protec-
tion Ð the atmosphere within the bulb
is pressurized. Failure to observe this pre-
caution can lead to personal injury should
the bulb be damaged.<
Driver's side
1.Apply the screwdriver from the on-
board tool kit and pull off the lamp
cover
Caution when handling the screw-
driver, as otherwise personal
injury can occur or the vehicle can be
damaged.<
2.Press the bulb holder downward and
remove
3.Remove the bulb, mount a new bulb
4.Apply the bulb holder with the lower
edge to the bracket and press it in until
the lamp base locks in place.
Front passenger side
Before replacing the bulb, remove the res-
ervoir for the windshield washing system
from the bracket. To do so, loosen the bolt,
refer to arrow, and place the reservoir to
one side.
Bear in mind that the windshield
washing system reservoir is heavy. If
you do not, injuries or damage to the vehi-
cle can occur.<
For bulb replacement procedure, refer to
Driver's side.
Halogen high beams
H7 bulb, 55 Watts
Always wear gloves and eye protec-
tion Ð the atmosphere within the bulb
is pressurized. Failure to observe this pre-
caution can lead to personal injury should
the bulb be damaged.<
Driver's side
1.Open the clip and remove the lamp
cover
2.Press the bulb holder downward and
remove, refer to Low beams
3.Pull off the lamp base; fit a new lamp
base