light BMW X3 3.0I 2004 E83 Owner's Manual
[x] Cancel search | Manufacturer: BMW, Model Year: 2004, Model line: X3 3.0I, Model: BMW X3 3.0I 2004 E83Pages: 132, PDF Size: 3.62 MB
Page 14 of 132
Cockpit
12
Indicator and warning
lamps
Technology that monitors itself
The indicator and warning lamps identified
by the
+ symbol are subjected to an oper-
ation check each time you switch on the
engine. They each light up once for differ-
ent periods of time.
When a malfunction occurs in a monitored
system, the corresponding lamp will either
fail to go out when the engine is started, or
it will come on again during normal driving.
Detailed information is provided on the
specified pages.
Please fasten safety belt
+ 30
Airbags
+ 54
Brake system
+
With handbrake released 52/ 96
With handbrake set 38
With other warning lamps 52
Brake warning lamp for Canadian
models
Driving stability control systems/
Antilock Brake System
+ 53
Antilock Brake System ABS/
Chassis control system for Cana-
dian models
Brake pads
+ 96
Dynamic Stability Control DSC/
xDrive
+ 50/ 52
Flat Tire Monitor
+ 53
Automatic transmission
+ 39
Engine oil + 94
Service Engine Soon
+ 98
Service Engine Soon
+ 37
warning lamp for Canadian
models.
Check Gas Cap
+
Engine electronics + 37
Battery charge current
+ 105
Topping up coolant 95
Topping up washer fluid 94
Lamp defective 57
Turn signal indicators 41
Fog lamps 58
Headlamp flasher 41
High beams 58
Cruise control 43
Page 15 of 132
At a glance
Controls
Driving tips
Mobility Reference
13
Colors
The indicator and warning lamps can light
up in different colors and combinations.
The following section explains the signifi-
cance of the individual colors as well as
how you should respond when they
appear.
>Red:
Stop the vehicle immediately
or
an important reminder
>Yellow:
Have the system inspected as soon as
possible
or
for your information
>Green:
For your information
>Blue
For your information.
Page 20 of 132
Opening and closing
18
Opening and closing
Key set
1Master keys with remote control deter-
mine the functions of the Key Memory,
refer to page 33.
You can mark the keys using the col-
ored decals you received on taking
delivery of the vehicle
There is an extended-life battery
in every master key which is
charged automatically in the ignition
lock as you drive.
If you have any master keys that are not
being used on a regular basis, you
should therefore remember to recharge
these units by using them to drive the
vehicle for an extended period at least
once a year.<
2Spare key for storage in a safe place,
such as in your wallet.
This key cannot be used to open the
lock for the glove compartment. This is
an advantage, e.g. at a hotel. The key is
not intended for constant use.
Central locking system
The concept
The central locking system is ready for
operation whenever the driver's door is
closed. The system engages or releases
the locks on the
>doors
>tailgate >fuel filler door.
The central locking system can be oper-
ated from the outside
>via the remote control
>via the driver's door lock
and from inside via the button for the cen-
tral locking system.
When the system is locked from inside, the
fuel filler door remains unlocked, refer to
page 20.
The anti-theft system is automatically acti-
vated whenever you activate the central
locking system from outside the vehicle.
This prevents the doors from being
unlocked via the safety lock buttons or
door handles. The alarm system is also
armed or disarmed.
In an accident, the central locking system
automatically unlocks the vehicle. In addi-
tion, the hazard warning flashers and inte-
rior lamps switch on.
You can have an acknowledgment
signal set to confirm that the vehicle is
correctly locked.<
Opening and closing Ð from
outside
Using the remote control
The remote control provides two additional
functions for the central locking system:
>Switching on the interior lamps, refer to
page 19.
You can also use this function to locate
your vehicle in parking garages etc.
>Opening the tailgate, refer to page 19.
The tailgate will open slightly, regard-
less of whether it was previously locked
or unlocked.
Page 21 of 132
Reference
At a glance
Controls
Driving tips
Mobility
19
In addition, the remote control offers you
another function:
>Panic mode
In case of danger, you can trigger an
alarm.
When you engage/release the vehicle
locks, you simultaneously activate/deacti-
vate the anti-theft system, arm/disarm the
alarm system, and switch the interior lamps
on/off.
As a reminder that the ignition key is
still in the ignition lock after you open
the driver's door, you can have a sound sig-
nal set.<
Protect the remote control against
unauthorized use by handing over
only the spare key, for example when using
hotel valet parking.<
Because any persons or animals left
unattended in a parked vehicle could
lock the doors from the inside, you should
always take the vehicle's keys with you so
that the vehicle can be opened again from
the outside at any time.<
Unlocking
Press the button.
Press the button once to unlock the driverÕs
door only; press a second time to unlock all
remaining doors as well as the tailgate and
the fuel filler door.
Convenience opening mode
Press and hold the button. The windows
and the sliding panel of the panorama glass
roof are opened.
Press the button a second time and hold.
The panorama glass roof is opened.
If you desire, you can have this spe-
cial feature activated/deactivated on
a vehicle-specific basis.<
Locking and securing
Press the button.
If you desire, the vehicle locks auto-
matically if no door or lid is opened
after unlocking. You may have this function
set on a vehicle-specific basis if you wish.<
Switching off the tilt alarm sensor*
and interior motion sensor*
Press the button once again directly
after locking.
For details, refer to page 25.
Switching on the interior lamps
If the vehicle is locked, press the
button.
Panic mode*
By pressing and holding the button for
more than approx. two seconds, you can
trigger the alarm system in response to any
impending danger.
To switch off the alarm: press any of the
buttons.
Unlocking tailgate
Press the button.
The tailgate will open slightly, regardless of
whether it was previously locked or
unlocked.
Before and after a trip, ensure that the
tailgate has not been opened uninten-
tionally.
A previously locked tailgate is also locked
after closing.<
If you desire, the tailgate can only be
opened using the remote control if the
vehicle is unlocked. This can be adjusted.<
Malfunctions
The remote control system may be affected
by other units or equipment operating in
the immediate vicinity of your vehicle.
Should the remote control fail to operate
owing to interference of this kind, you can
respond by using the master key to unlock
your vehicle at one of the doors.
In case of faults, please contact your BMW
Sports Activity Vehicle Center. You can
also obtain replacement keys there.
If it is no longer possible to lock the vehicle
via the remote control, the battery is dis-
charged. Use this remote control during an
extended drive; this will recharge the bat-
tery, refer to page 18.
Page 24 of 132
Opening and closing
22
Electric power windows
Opening and closing windows
As of ignition key position 1:
>Press the switch up to the resistance
point:
The window continues to move as long
as you continue to press the switch
>Press the switch beyond the resistance
point:
The window moves downward auto-
matically. Briefly press the switch again
to stop the opening movement.
You can close the windows in the same
manner by pulling the switch.
After switching off the ignition
You can operate the electric power win-
dows for up to 15 minutes as long as nei-
ther of the front doors has been opened.
When leaving the vehicle parked,
always remove the remote control
from the ignition lock and close the doors;
this precaution prevents children from
operating the electric power windows and
injuring themselves, etc.<
For convenience operation with the door
lock, refer to page 20.
Anti-trapping mechanism
If the closing force rises beyond a pre-
defined threshold during closing, the sys-
tem will immediately stop moving the win-
dow prior to lowering it slightly.
Despite the anti-trapping mechanism
you should always inspect the win-
dow's travel path prior to closing it, as the
safety system might fail to detect certain kinds of obstructions, such as very thin
objects, and the window would continue
closing.
You can disable the anti-trapping mecha-
nism by pressing the switch beyond the
resistance point and holding it.<
Following interruptions in electrical
power supply
After disconnecting the battery, the anti-
trapping mechanism must be reinitialized.
To do this, open and close the windows
once and continue pull the switch for 2 sec-
onds after closing.
Safety switch
With the safety switch, you can prevent the
rear windows from being opened or closed
via the switches in the rear passenger area,
by children, for example. The indicator
lamp lights up when this safety feature is
activated.
Press the safety switch whenever
children are riding in the rear of the
vehicle. Careless use of the electric power
windows can lead to injury.<
You can deactivate the function again
as of ignition key position 1.<
Accessories in the window area
After installing any accessory Ð such as a
clamp-on antenna for a portable phone Ð
within the window's travel range, you will
need to have the system reinitialized for
use under the new conditions. Please con-
tact your BMW Sports Activity Vehicle Cen-
ter.
Page 27 of 132
Reference
At a glance
Controls
Driving tips
Mobility
25
>The high beams, which flash on and off
in the same rhythm.
Arming and disarming the alarm
system
When the vehicle is locked or unlocked
with the key or the remote control, the
alarm system is also simultaneously armed
or disarmed.
If the alarm system has been properly
armed, the hazard warning flashers light up
once.
You can have different acknowledg-
ment signals set to confirm arming
and disarming.<
You can also open the tailgate with the sys-
tem armed using the button on the
remote control, refer to page 19. When you
close the tailgate, the system is rearmed.<
Switching off the alarm
>Unlock the vehicle using the remote
control, refer to page 19
>Turn the ignition key to position 1.
Indicator lamp displays
>The indicator lamp below the interior
rearview mirror flashes continuously:
the system is armed
>The indicator lamp flashes during arm-
ing: door(s), the hood or tailgate are not
completely closed. Even if you do not
close the alerted area, the system
begins to monitor the remaining areas,
and the indicator lamp flashes continu-
ously after 10 seconds. However, the
interior motion sensor is not activated >If the indicator lamp goes out when the
system is disarmed: no manipulation or
attempted intrusions have been
detected in the period since the system
was armed
>If the indicator lamp flashes for 10 sec-
onds after the system is disarmed: an
attempted entry has been detected in
the period since the system was armed.
Following triggering of an alarm, the indica-
tor lamp will flash continuously.
Avoiding unintentional alarms
The tilt alarm sensor and interior motion
sensor may be switched off at the same
time. You can do this to prevent a false
alarm from being triggered in garages with
elevator ramps, for instance, or when the
vehicle is transported by trailer or train:
Lock twice:
>Press the button on the remote
control twice consecutively
>Lock using the door lock twice.
The indicator lamp lights up briefly and
then flashes continuously. The tilt alarm
sensor and the interior motion sensor are
deactivated as long as the system is
armed.
If you wish, the tilt alarm sensor and
interior motion sensor are perma-
nently switched off. You can have this set
at your BMW Sports Activity Vehicle Cen-
ter.<
Interior motion sensor
In order for the interior motion sensor to
function properly, the windows and pan-
orama glass roof must be completely
closed.
However, be sure to switch off the interior
motion sensor Ð refer to Avoiding uninten-
tional alarms Ð when you
>leave children or animals in the vehicle
>the windows or panorama glass roof
are to remain open.
The tilt alarm sensor and interior
motion sensor are switched off inad-
Page 30 of 132
Adjustments
28 the ensuing loss of vehicle control could
lead to an accident.
Especially on the passenger's side, do not
incline the backrest too far to the rear while
the vehicle is being driven, as otherwise
there is a danger in the event of an accident
of sliding under the safety belt, eliminating
the protection normally provided by the
belt.<
Please observe the information on using
safety belts provided on page 30 and the
information on the head restraints on
page 28.
Seat adjustment
To ensure that the safety systems
continue to provide optimized protec-
tion, please observe the adjustment
instructions above.<
1Longitudinal direction
Pull the lever and slide the seat into the
desired position.
After you release the lever, move the
seat forward or backward slightly so
that it engages fully
2Height
Pull the lever and apply weight to or
remove weight from the seat as
required3Backrest angle
Pull the lever and apply weight to or
remove weight from the backrest as
requiredAdjusting the BMW sports seat*
You can also adjust the tilt and the thigh
support:
1Upward tilt:
Pull the lever as many times as required
to set the desired tilt
2Downward tilt:
Press the lever as many times as
required to set the desired tilt
3Thigh support:
Pull the lever and move the thigh sup-
port in the longitudinal direction
Head restraints
Align the head restraints so that their
center is approximately at ear level,
as otherwise the risk of spinal injuries is
increased in the event of an accident.<
Page 32 of 132
Adjustments
30 3.Press MEMORY button:
The indicator lamp in the button lights
up
4.Press the desired memory button 1, 2
or 3:
The indicator lamp goes out.
Selecting a stored setting
Do not call up a position from the
memory while the vehicle is moving,
as otherwise there is a risk of accident from
unexpected seat movement.<
Convenience mode
1.Open the driver's door after unlocking
or turn the ignition key to position 1
2.Briefly press the desired memory but-
ton 1, 2 or 3.
The system immediately cancels the
adjustment procedure when you press
one of the seat adjustment buttons or
use one of the memory buttons.
Safety feature
1.Close the driver's door and turn the
ignition key to position 0 or 2
2.Press the desired memory button 1, 2
or 3 and maintain pressure until the
adjustment process has been com-
pleted.
If you press the
MEMORY button
accidentally:
Press the button a second time Ñ the indi-
cator lamp goes out.<
You can have your vehicle pro-
grammed to automatically dial in your
own individual adjustment settings for the
seat and exterior mirror position whenever
you use your personal remote control to
unlock the vehicle.<
If you make use of this adjustment, be
sure that the footwell behind the
driver's seat is unobstructed before
unlocking the vehicle. If you fail to do so,
any persons, animals or objects behind the
seat could be injured or damaged by a
rearward movement of the seat.<
Heated seats*
The seat cushion and backrest can be
heated when the ignition key is in
position 2.
To call up different temperature levels:
Press the button repeatedly.
To switch off from a higher heat setting:
Press the button and hold it slightly longer.
Safety belts
Even though there is an airbag, wear a
safety belt every time you get in the vehi-
cle. Although airbags enhance safety by
providing added protection, they are not a
substitute for safety belts.
Fastening
Make sure you hear the latch plate engage
in the belt buckle.
Please fasten safety belt warning
lamp:
Lights up for a few seconds or until
safety belts are fastened. Depending on
you vehicle version, a signal
* sounds
simultaneously.
Page 33 of 132
Reference
At a glance
Controls
Driving tips
Mobility
31
Releasing
1.Press the red button in the buckle
2.Hold the belt
3.Guide the belt back into its reel.
The upper shoulder strap's anchorage
point will be in the correct position for seat
occupants of every build if the seat is cor-
rectly adjusted, refer to page 27.
The two rear safety belt buckles integrated
in the rear seat are for passengers sitting
on the left and right. The belt buckle
embossed with the word CENTER is
intended exclusively for use by passengers
riding in the center position.<
Damage to safety belts
If the safety belts are damaged or
stretched in an accident: have the
entire belt system, including the tensioning
mechanisms, replaced at your BMW Sports
Activity Vehicle Center. Have the belt
anchorage points inspected for damage at
the same time. Failure to observe this pre-
caution may prevent the safety belts from
effectively providing optimal protection
when needed. If a child-restraint system
was in the vehicle during an accident, con-
sult the manufacturer's instructions regard-
ing replacement.<
Steering wheel
Adjustments
Do not adjust the steering wheel while
the vehicle is moving. There is a risk
of accident from unexpected movement.< 1.Fold the clamping lever downward
2.Adapt the steering wheel in the longitu-
dinal direction and height of the seat
position
3.Fold the clamping lever back up.
Steering wheel heating*
The button for steering wheel heating is
located in the steering wheel, refer to
page 14.
Steering wheel heating: switching on/off.
The steering wheel heating operates from
ignition key position 2.
Press the button to activate or deactivate
this system.
The indicator lamp within the button lights
up when the steering wheel heating is in
operation.
Mirrors
Adjusting exterior mirrors
1Mirror switch for 4-way adjustment
2Left/right selector switch
Page 34 of 132
Adjustments
32 To prevent the exterior mirrors on this
vehicle from being damaged, always
fold them in by hand before entering an
automatic car wash.<
Adjusting manually
You can also adjust the mirrors manually:
Press the edges of the mirror glass.
Storing the mirror positions, refer to Seat
and mirror memory on page 29.
Convex mirror
The mirror on the passenger's side
features a lens with a more convex
surface than the mirror installed on the
driver's side. When estimating the distance
between yourself and other traffic, bear in
mind that the objects reflected in the mirror
are closer than they appear. This means
that estimations of the distance to following
traffic should not be regarded as precise.<
Electric heaters
Both mirrors are heated automatically in
ignition key position 2.
Passenger-side exterior mirror tilt
function
Automatic curb monitor*
1.Select the driver's exterior mirror with
the switch 1
2.When you engage reverse gear or
selector-lever position R, the exterior
mirror on the front passenger side tilts
downward slightly. This allows the
driver to see the area immediately adja-
cent to the vehicle Ð such as a curb Ð
when parking, etc.You can have the angle of downward
tilt set in dependence on the key
used.<
Interior rearview mirror
To reduce the dazzle effect of following
vehicles at night, turn the knob.
Interior and exterior mirrors,
automatic dimming feature*
These mirrors automatically dim through an
infinitely-variable range. They automatically
revert to their undimmed mode whenever
the transmission is placed in reverse gear
or selector lever in position R.
For trouble-free operation, keep the
photocells unobstructed and clean
and do not cover the area between the
interior rearview mirror and the windshield.
Do not attach any kind of stickers on the
windshield in front of the mirror, either.<