BMW X5 XDRIVE 30I 2010 E70 Owner's Manual
Manufacturer: BMW, Model Year: 2010, Model line: X5 XDRIVE 30I, Model: BMW X5 XDRIVE 30I 2010 E70Pages: 300, PDF Size: 12.41 MB
Page 131 of 300

Driving tips
This section is designed to provide you
with extra support by supplying information
useful in dealing with specific driving
and operating conditions.
Driving tips
ba8_e70ag.book  Seite 129  Freitag, 5. Juni 2009  11:42 11 
Page 132 of 300

Things to remember when driving
130
Things to remember when driving
Break-in period
Moving parts need breaking-in time to adjust to 
each other. To ensure that your vehicle contin-
ues to provide optimized economy of operation 
throughout an extended service life, we request 
that you devote careful attention to the follow-
ing section.
Engine and rear axle differential
Always obey all official speed limits.
Up to 1,200 miles/2,000 km
Drive at various engine and vehicle speeds, but 
do not exceed:
>Gasoline engine
4,500 rpm or 100 mph/160 km/h
>Diesel engine
3,500 rpm or 90 mph/150 km/h
Avoid full-throttle operation and use of the 
transmission's kick-down mode during these 
initial miles.
From 1,200 miles/2,000 km
The engine and vehicle speed can gradually be 
increased.
Tires
Due to technical factors associated with their 
manufacture, tires do not achieve their full trac-
tion potential until after an initial break-in 
period. Therefore, drive reservedly during the 
first 200 miles/300 km.
Brake system
Brakes require an initial break-in period of 
approx. 300 miles/500 km to achieve optimized 
contact and wear patterns between brake pads 
and rotors. Drive in a reserved manner during 
this break-in period.
Following part replacement
Observe the break-in instructions again if com-
ponents mentioned above must be replaced 
after subsequent driving operation.
Saving fuel
The fuel consumption of your vehicle depends 
on various factors. Through a few simple steps, 
your driving style, and regular maintenance, you 
can have a positive influence on your fuel con-
sumption and environmental impact.
Removing unnecessary cargo
Additional weight increases fuel consumption.
Removing add-on parts after use
Remove unneeded auxiliary mirrors, roof or rear 
luggage racks after use. Add-on parts attached 
to the vehicle impede the aerodynamics and 
increase the fuel consumption.
Closing windows and glass sunroof*/
panorama glass sunroof*
An open glass sunroof/panorama glass sunroof 
or open windows likewise increase the drag 
coefficient and therefore the fuel consumption.
Checking tire inflation pressures 
regularly
Check and correct the tire inflation pressure as 
needed at least twice a month and before long 
trips.
An insufficient tire inflation pressure increases 
the rolling resistance and thus increases the 
fuel consumption and tire wear.
Driving off immediately
Do not allow the engine to warm up by leaving it 
running while the vehicle remains stationary. 
Instead, begin to drive at a moderate engine 
ba8_e70ag.book  Seite 130  Freitag, 5. Juni 2009  11:42 11 
Page 133 of 300

Driving tips
 131Reference
At a glance
Controls
Communications
Navigation
Entertainment
Mobility
speed. This is the fastest way for the cold 
engine to reach its operating temperature.
Thinking ahead when driving
Avoid unnecessary acceleration and braking. 
To do so, maintain the appropriate distance 
from the vehicle in front of you. An anticipatory 
and smooth driving style reduces fuel con-
sumption.
Avoiding high engine speeds
Driving at a low engine speed reduces fuel con-
sumption and minimizes wear.
Taking advantage of coasting
The flow of fuel is interrupted when coasting.
Switching off engine during longer 
stops
Switch off the engine at longer stops such as 
traffic signals, railroad crossings, or in traffic 
congestions. You achieve fuel savings even if 
the standing time is as short as approx. 4 sec-
onds.
Switching off functions currently not 
required
Functions such as air conditioning, seat heat-
ing, or rear window defrosting consume a lot of 
energy and require additional fuel. Their influ-
ence is particularly pronounced in city traffic 
and stop & go operation. For this reason, it is a 
good idea to switch these functions off when 
they are not really needed.
Having maintenance carried out
Have the vehicle serviced regularly in order to 
achieve the optimum economy and service life 
of your vehicle. BMW recommends having the 
maintenance performed by a BMW Sports 
Activity Vehicle Center. Also pay attention to 
the BMW maintenance system, refer to 
page244.
General driving notes
Closing liftgate
Operate the vehicle only when the liftgate 
is completely closed. Otherwise, exhaust 
fumes could enter into the passenger compart-
ment.<
If it is absolutely necessary to drive with the lift-
gate open:
1.Close all windows as well as the glass sun-
roof
*/panorama glass sunroof*.
2.Increase the air volume of the automatic cli-
mate control to a high level, refer to 
page109.
Hot exhaust system
As in all vehicles, extremely high temper-
atures are generated on the exhaust sys-
tem. Do not remove the heat shields installed 
adjacent to it, and never apply undercoating to 
them. When driving, standing at idle and while 
parking take care to avoid possible contact 
between the hot exhaust system and any highly 
flammable materials such as hay, leaves, grass, 
etc. Such contact could lead to a fire, and with it 
the risk of serious property damage as well as 
personal injury. Do not touch hot tailpipes, as 
otherwise there is a danger of burns.<
Diesel particulate filter*
Soot particles are collected in the diesel partic-
ulate filter and periodically burned away at high 
temperatures. This cleaning process lasts a few 
minutes. You will notice it sometimes by the 
fact that the engine temporarily runs slightly 
less smoothly and requires a slightly higher 
engine speed to delivery the usual power. You 
may also hear sounds and observe a slight 
amount of smoke coming from the exhaust up 
to even a few moments after the engine is 
switched off.
ba8_e70ag.book  Seite 131  Freitag, 5. Juni 2009  11:42 11 
Page 134 of 300

Things to remember when driving
132
Hydroplaning
When driving on wet or slushy roads, 
reduce road speed. If you do not, a wedge 
of water can form between tires and road sur-
face. This phenomenon is referred to as hydro-
planing, and is characterized by a partial or 
complete loss of contact between the tires and 
the road surface, ultimately undermining your 
ability to steer and brake the vehicle.<
The risk of hydroplaning increases as the tread 
depth of the tires decreases, also refer to Mini-
mum tread depth on page236.
Driving through water
Maximum water depth:
>BMW X5 20 in/50 cm
>BMW X6 17 in/45 cm
Only drive through water up to the above-
mentioned depth at no greater than walk-
ing speed; otherwise, the engine, electrical sys-
tem, and transmission can be damaged.<
Braking safely
Your BMW is equipped with ABS as a standard 
feature. In situations that require it, it is best to 
brake with full force. Since the vehicle maintains 
steering responsiveness, you can still avoid 
possible obstacles with a minimum of steering 
effort.
Pulsation of the brake pedal, combined with 
sounds from the hydraulic circuits, indicate that 
ABS is in its active mode.
Do not drive with your foot resting on the 
brake pedal. Even light but consistent 
pedal pressure can lead to high temperatures, 
brake wear and possibly even brake failure.<
Driving in wet conditions
When roads are wet or there is heavy rain, 
briefly exert gentle pressure on the brake pedal 
every few miles. Monitor traffic conditions to 
ensure that this maneuver does not endanger 
other road users. The heat generated in this 
process helps dry the pads and rotors to ensure 
that full braking efficiency will then be available 
when you need it.
Hills
To prevent overheating and the resulting 
reduced efficiency of the brake system, 
drive long or steep downhill gradients in the 
gear in which the least braking is required. Even 
light but consistent pressure on the brake pedal 
can lead to high temperatures, brake wear and 
possibly even brake failure.<
The braking effect of the engine can be further 
increased by downshifting in the manual mode 
of the automatic transmission, if necessary into 
first gear, refer to page65. This prevents an 
excessive strain on the brakes.
Do not drive in idle or with the engine 
stopped, otherwise there will be no 
engine braking action or support of the braking 
force and steering. 
Never allow floor mats, carpets or any other 
objects to protrude into the area of movement 
of the pedals and impair their operation.<
Corrosion on brake rotors
When the vehicle is driven only occasionally, 
during extended periods when the vehicle is not 
used at all, and in operating conditions where 
brake applications are less frequent, there is an 
increased tendency for corrosion to form on 
rotors, while contaminants accumulate on the 
brake pads. This occurs because the minimum 
pressure which must be exerted by the pads 
during brake applications to clean the rotors is 
not reached.
Should corrosion form on the brake rotors, the 
brakes will tend to respond with a pulsating 
effect that even extended application will fail to 
cure.
When vehicle is parked
Condensation forms in the automatic climate 
control system during operation, and then exits 
under the vehicle. Traces of condensed water 
under the vehicle are therefore normal.
ba8_e70ag.book  Seite 132  Freitag, 5. Juni 2009  11:42 11 
Page 135 of 300

Driving tips
 133Reference
At a glance
Controls
Communications
Navigation
Entertainment
Mobility
Loading
To avoid loading the tires beyond their 
approved carrying capacity, never over-
load the vehicle. Overloading can lead to over-
heating and increases the rate at which damage 
develops inside the tires. The ultimate result 
can assume the form of a sudden blow-out.<
Make sure that no fluids leak in the cargo 
bay; otherwise the vehicle could be dam-
aged.<
Determining loading limit
1.Locate the following statement on your 
vehicle's placard
*:
The combined weight of occupants 
and cargo should never exceed 
YYY lbs. or XXX kg. Otherwise, this could 
damage the vehicle and produce unstable 
vehicle operating conditions.<
2.Determine the combined weight of the 
driver and passengers that will be riding in 
your vehicle.
3.Subtract the combined weight of the driver 
and passengers from YYY lbs. or XXX kg.
4.The resulting figure equals the available 
amount of cargo and luggage load capacity. 
For example, if the YYY amount equals 
1,400 lbs. and there will be five 150 lbs. 
passengers in your vehicle, the amount of 
available cargo and luggage load capacity is 
650 lbs.: 
1,400 lbs. minus 750 lbs. = 650 lbs.5.Determine the combined weight of luggage 
and cargo being loaded on the vehicle. That 
weight may not safely exceed the available 
cargo and luggage load capacity calculated 
in step 4.
6.If your vehicle will be towing a trailer, part of 
the load from your trailer will be transferred 
to your vehicle. Consult the manual for 
transporting a trailer to determine how this 
may reduce the available cargo and luggage 
load capacity of your vehicle.
Load
BMW X5:
BMW X6:
The permissible load is the total of the weight of 
occupants and cargo/luggage. The greater the 
weight of occupants, the less cargo/luggage 
can be transported.
ba8_e70ag.book  Seite 133  Freitag, 5. Juni 2009  11:42 11 
Page 136 of 300

Things to remember when driving
134
Stowing cargo
BMW X5
BMW X6
>Load heavy cargo as far forward and as low 
as possible, placing it directly behind the 
backrest.
>Cover sharp edges and corners.>When transporting very heavy cargo with 
unoccupied rear seats, insert the safety 
belts, the outer safety belts in the BMW X5, 
into the buckles on the opposite sides.
>Do not pile objects higher than the top edge 
of the backrest.
>Wrap sharp-edged or pointed objects 
which could strike the rear window while 
driving.
Securing cargo
BMW X5
BMW X6
>Use the luggage net*, retaining straps*, or 
securing straps to hold down small and 
lightweight luggage and cargo.
>For larger and heavier pieces, heavy-duty 
cargo straps
* are available from your BMW 
Sports Activity Vehicle Center. Four lashing 
eyes
* mounted in the cargo bay are used to 
secure these heavy-duty cargo straps, refer 
to illustrations.
>Observe the special instructions supplied 
with the heavy-duty cargo straps.
Position and secure the cargo as 
described above, so that it cannot endan-
ba8_e70ag.book  Seite 134  Freitag, 5. Juni 2009  11:42 11 
Page 137 of 300

Driving tips
 135Reference
At a glance
Controls
Communications
Navigation
Entertainment
Mobility
ger the car's occupants, for example if sudden 
braking or evasive maneuvers are necessary.
Never exceed either the approved gross vehicle 
weight or either of the approved axle weights, 
refer to page271, as excessive loads can pose 
a safety hazard, and may also place you in viola-
tion of traffic safety laws. 
You should never transport unsecured heavy or 
hard objects in the passenger compartment, as 
they could fly around and pose a safety hazard 
to the vehicle's occupants during abrupt brak-
ing or evasive maneuvers.
Use only the lashing eyes pictured to fasten the 
heavy-duty cargo straps. Do not secure cargo 
with the attachment points for the top tether, 
refer to page56; otherwise they could be dam-
aged.<
Roof-mounted luggage rack*
A special rack system is available as an option 
for your BMW. Please comply with the precau-
tions included with the installation instructions.
Loading roof-mounted luggage rack
Because roof racks raise the vehicle's center of 
gravity when loaded, they have a major effect on 
its handling and steering response. You should 
therefore always remember not to exceed the 
approved roof load capacity, the approved 
gross vehicle weight or the axle weights when 
loading the rack.
You can find the specified weights under 
Weights on page271.
The load on the roof must be evenly distributed 
and must not extend outward beyond the limits 
of the loading surface. Always stow the heaviest 
pieces on the bottom. Be sure that adequate 
clearance is maintained for raising the glass 
sunroof
*/panorama glass sunroof* and that 
objects do not project into the opening path of 
the liftgate.
Secure roof-mounted cargo correctly and 
securely to prevent it from shifting or falling off 
during the trip.
Drive smoothly. Avoid sudden acceleration and 
braking maneuvers. Take corners gently.
Driving on poor roads
Y our B MW  is at hom e on a ll r oa ds a nd surfac e s. 
It combines a 4-wheel drive system with the 
advantages of a normal passenger car.
Do not drive on unpaved terrain, as other-
wise the vehicle may be damaged.<
When you are driving on poor roads, there are a 
few points which you should strictly observe for 
your own safety, for that of your passengers, 
and for the safety of the vehicle:
>Familiarize yourself with the vehicle before 
driving off and avoid taking risks at all costs.
>Adapt your driving speed to the road condi-
tions. The steeper and rougher the road 
surface is, the lower the speed should be.
>If you want to drive on very steep uphill or 
downhill gradients, make sure beforehand 
that the engine oil and coolant levels are 
near the MAX mark, refer to page240.
BMW X5: you can operate your vehicle on 
uphill and downhill gradients with a maxi-
mum slope of 50 %.
>On very steep downhill slopes, use Hill 
Descent Control HDC, refer to page90. 
BMW X5: it is possible to start off on inclines 
of up to 33 %. The permissible body roll is 
50 %.
>While driving, watch carefully for obstacles 
such as rocks or holes. Try to avoid these 
obstacles whenever possible.
>Make sure that the undercarriage does not 
touch the ground, for example on crests and 
bumpy roads. The ground clearance of the 
vehicle is a maximum of approx. 8 in/20 cm. 
Please note that the ground clearance can 
vary depending on loading and the driving 
conditions of the vehicle.
>Only drive through road surface water up to 
a maximum water depth of
>BMW X5 20 in/50 cm
>BMW X6 17 in/45 cm
and only drive at walking speed; do not 
remain stationary.
ba8_e70ag.book  Seite 135  Freitag, 5. Juni 2009  11:42 11 
Page 138 of 300

Things to remember when driving
136 >After driving through water at low speed, 
lightly press the brake pedal several times 
to dry the brakes and to prevent the braking 
effect from being reduced by wetness.
>Depending on the condition of the surface, 
it may be practical to briefly activate DTC, 
refer to DTC Dynamic Traction Control on 
page89.
>If the drive wheels spin on one side, depress 
the accelerator pedal sufficiently so that the 
driving stability control systems can distrib-
ute the drive forces to the individual wheels.
Please note the following points after driving on 
poor roads to maintain the driving safety of your 
BMW:
>Clean the coarsest dirt from the body.
>Clean mud, snow, ice etc. from the wheels 
and tires and check the tires for damage.
ba8_e70ag.book  Seite 136  Freitag, 5. Juni 2009  11:42 11 
Page 139 of 300

Driving tips
 137Reference
At a glance
Controls
Communications
Navigation
Entertainment
Mobility
ba8_e70ag.book  Seite 137  Freitag, 5. Juni 2009  11:42 11 
Page 140 of 300

ba8_e70ag.book Seite 138 Freitag, 5. Juni 2009 11:42 11