ESP BMW Z4M COUPE 2007 E86 User Guide

Reference
At a glance
Controls
Driving tips
Mobility
33
9Connecting hose for connecting compres-
sor and sealant bottle or compressor and
wheel
Connector, cable and connecting hose are
attached to the bottom of the compressor.
Using the M Mobility System
To repair a flat tire with the M Mobility System,
proceed as follows:
>Fill sealant into wheel
>Distribute sealant
>Restore tire inflation pressure
Filling sealant into wheel
Strictly adhere to the specified order, oth-
erwise highly pressurized sealant could
escape.<
1.Shake sealant bottle.
2.Screw hose9 onto connection of sealant
bottle.
3.Unscrew and remove dust cap from valve of
defective wheel and screw filler hose2 of
sealant bottle onto valve.
4.Insert sealant bottle on compressor hous-
ing so that the bottle is in an upright posi-
tion.
5.Make sure that the device is switched off,
position 0.
6.Insert connector 3 into cigarette lighter
socket inside the vehicle.
7.With the ignition switched on:
Switch on the device and allow it to run for
approx. 3 minutes to fill the wheel with seal-
ant. It is not important what inflation pres-
sure the tire has after this.8.Switch off device.
9.Remove connecting hoses from connection
of sealant bottle and tire valve.
Stow the M Mobility System in the vehicle
again.
Distributing sealant
Immediately drive approx. 2 miles/3 km so that
the sealant is evenly distributed in the tire.
Do not exceed a speed of 35 mph or
60 km/h. Do not drive slower than 12 mph
or 20 km/h if possible.<
Restoring tire inflation pressure
1.After approx. 2 miles/3 km, pull over at a
suitable location.
2.Screw compressor hose9 directly onto tire
valve.
3.Insert connector 3 into cigarette lighter
socket inside the vehicle.
4.Correct tire inflation pressure to 29 psi/
200 kPa. With the ignition switched on:
>To increase inflation pressure: switch on
the compressor, position I. To check the
current pressure setting, briefly switch
off the device.
Do not allow the compressor to run
for more than 10 minutes, otherwise
the device will overheat and may be dam-
aged.<
>To reduce inflation pressure: press but-
ton 8.
If the inflation pressure is not maintained,
drive the vehicle again, refer to Distribut-
ing sealant. Then repeat steps 1 to 4 once.
Using the M Mobility System can be ineffective
with tire punctures larger than approx. 1/6 in/
4 mm. Please contact the nearest BMW center
or a workshop that works according to BMW
repair procedures with correspondingly trained
personnel if the tire cannot be made ready for
driving with the M Mobility System.<
The tire inflation pressure must be at least
29 psi/200 kPa. Otherwise do not con-
tinue driving.<
ba5.book Seite 33 Mittwoch, 28. Februar 2007 1:09 13

Reference
At a glance
Controls
Driving tips
Mobility
43
Engine compartment28
Engine data38
Engine oil28
– adding29
– additives29
– alternative oil grades30
– approved engine oils29
– dipstick29
– indicator/warning lamp10
– oil grades, refer also to
Approved engine oils29
Engine oil level28
– checking29
– indicator/warning lamp10
Engine oil pressure28
– indicator/warning lamp10
Engine oil sensor
– indicator/warning lamp10
Engine oil temperature, refer
to Engine oil
thermometer17
Engine oil thermometer17
Engine output, refer to Engine
data38
Engine speed, refer to Engine
data38
ESP Electronic Stability
Program, refer to Dynamic
Stability Control DSC18
F
Fasten safety belts
– warning lamp11
Filling sealant into wheel33
Flat tire
– Flat Tire Monitor18
– M Mobility System31
– Tire Pressure Monitor18
Flat tire, refer to Repairing a
flat tire31
Flat Tire Monitor FTM18
– indicator/warning
lamp11,18
– snow chains27
FTM, refer to Flat Tire
Monitor18Fuel
– capacity, refer to
Capacities41
– display17
– quality26
Fuel, refer to Fuel
specifications26
Fuel display, refer to Fuel
gauge17
Fuel reserve indicator, refer to
Fuel gauge17
Fuel tank capacity, refer to
Capacities41
G
Gasoline, refer to Fuel
specifications26
Gross weight, refer to
Weights41
Ground clearance22
H
Hazard warning flashers12
Headlamp flasher
– indicator lamp10
Headlamp washer reservoir
– volume, refer to
Capacities41
Height, refer to
Dimensions39,40
High beams
– indicator lamp10
Hood28
Horn8
I
Indicator/warning lamp
– brakes11
– Flat Tire Monitor18
– Tire Pressure Monitor19
Indicator and warning lamps,
overview10
Inflation pressure monitoring,
refer to
– Flat Tire Monitor18
– Tire Pressure Monitor18Inspection, refer to Service
interval display17
Instrument cluster10
Instrument panel, refer to
Cockpit8
Instrument panel, refer to
Instrument cluster10
Interval
– display, service17
K
Knock control26
L
Length, refer to
Dimensions39,40
Longlife oils30
– alternative oils30
– approved engine oils29
Low-beam headlamps
– indicator lamp11
Low beams
– indicator lamp, defective
bulb11
Luggage compartment
capacity, refer to Cargo bay
capacity41
Luggage compartment lid
– indicator lamp11
M
M Mobility System31
– compressor32
– viscosity32
Maintenance
– refer to Service interval
display17
Manufacturer5
Measurements, refer to
Dimensions39,40
Mobility System31
O
Octane numbers, refer to Fuel
specifications26
ba5.book Seite 43 Mittwoch, 28. Februar 2007 1:09 13

Refueling
So that you have important specifications avail-
able to you when you stop to refuel, we recom-
mend that you fill out this table with the data
that apply to your vehicle. The index of this Sup-
plementary Owner's Manual, or the index of the
BMW Z4 Owner's Manual, directs you to the
respective information.Fuel
Engine oil
The oil volume between the two marks on the
oil dipstick corresponds to approx.
1.4 US quarts/1.3 liters.
Tire inflation pressures
Specifications
Please enter your preferred fuel here.
Preferred oil grade
Summer tires
FrontRearWinter tires
FrontRear
Up to 2 persons
2 persons plus luggage
ba5.book Seite 47 Mittwoch, 28. Februar 2007 1:09 13