steering BUICK LACROSSE 2007 User Guide

The main components of the instrument panel are the following:
A. Air Outlets. SeeOutlet Adjustment on
page 177.
B. Interior Lamps Control. SeeInterior Lamps on
page 161.
C. Exterior Lamps Control. SeeExterior Lamps on
page 158. Fog Lamp Control. SeeFog
Lamps on page 160.
D. Turn Signal/Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 152.
E. Cruise Controls. SeeCruise Control on
page 154.
F. Instrument Panel Cluster. SeeInstrument
Panel Cluster on page 180.
G. DIC Buttons (If Equipped) and Hazard Warning
Flasher Button. SeeDIC Operation and
Displays on page 200andHazard Warning
Flashers on page 150.
H. Passenger Airbag Status Indicator. See
Passenger Airbag Status Indicator on page 183.
I. Audio System Controls. SeeAudio System(s)
on page 238.J. Hood Release. SeeHood Release on
page 349.
K. Parking Brake. SeeParking Brake on
page 117.
L. Tilt Lever (If Equipped). SeeTilt Wheel on
page 151. Telescoping Column Lever
(If Equipped). SeeTilt Wheel on page 151.
M. Horn. SeeHorn on page 150.
N. Audio Steering Wheel Controls (If Equipped).
SeeAudio Steering Wheel Controls on
page 280.
O. Shift Lever. SeeShifting Into Park (P) on
page 118.
P. Accessory Power Outlet. SeeAccessory Power
Outlet(s) on page 167.
Q. Climate Controls. SeeClimate Control System
on page 168orDual Automatic Climate
Control System on page 172.
R. Glove Box. SeeGlove Box on page 141.
149

Hazard Warning Flashers
Your hazard warning ashers let you warn others.
They also let police know you have a problem.
Your front and rear turn signal lamps will ash on
and off.
The hazard warning
asher button is located
in the center of the
instrument panel.
Your hazard warning ashers work no matter what
position your key is in, and even if the key is
not in the ignition switch.Press the button to make the front and rear turn
signal lamps ash on and off. Press the button
again to turn the ashers off.
When the hazard warning ashers are on, your
turn signals will not work.
Other Warning Devices
If you carry reective triangles, you can set them
up at the side of the road about 300 feet
(100 m) behind your vehicle.
Horn
Press near or on the horn symbols on your
steering wheel pad to sound the horn.
150

Tilt Wheel
If the vehicle has a tilt wheel it lets you adjust the
steering wheel before you drive. The steering
wheel can be raised to the highest level to give the
driver’s legs more room when you enter and exit
the vehicle.
The lever that allows
you to tilt the steering
wheel is located on
the left side of the
steering column.
To tilt the wheel, pull the lever down. Then move
the wheel to a comfortable position and pull
the lever up to lock the wheel in place.
Telescoping Column
If the vehicle has a telescoping column on the
steering wheel that adjusts the distance of
the steering wheel to the driver without moving
the driver’s seat.
The lever that makes
this adjustment is
located on the left side of
the steering column and
behind the tilt lever, if the
vehicle has this feature.
To adjust the steering wheel, pull the steering wheel
column lever down and push or pull the steering
wheel to a comfortable position. Then pull the lever
up to lock the wheel in place.
Do not drive the vehicle unless the telescoping
column is locked.
151

Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
GTurn and Lane Change Signals. See
Turn and Lane-Change Signals on page 152.
2Headlamp High/Low-Beam Changer.
SeeHeadlamp High/Low-Beam Changer
on page 153.
Flash-to-Pass. SeeFlash-to-Pass on page 153.
NWindshield Wipers. SeeWindshield Wipers
on page 153.
LQWindshield Washer. SeeWindshield
Washer on page 154.
For information on the headlamps, seeExterior
Lamps on page 158.
Turn and Lane-Change Signals
To signal a turn, move the lever up or down.
The lever returns to its original position when the
turn is completed.
An arrow on the
instrument panel
cluster will ash in the
direction of the turn or
lane change.
To signal a lane change, raise or lower the lever
until the arrow starts to ash. Hold it there until the
lane change is completed. The lever will return
to its original position when released.
Arrows that ash rapidly when signaling for a turn
or lane change, or that fail to work, may indicate
a burned-out signal bulb or fuse. Other drivers will
not see the signal. SeeFront Turn Signal and
Parking Lamps on page 397andTaillamps, Turn
Signal, Sidemarker, Stoplamps and Back-up
Lamps on page 398for turn signal bulb
replacement procedures. Also seeFuses and
Circuit Breakers on page 450for location of fuses.
A chime will sound if the turn signal is left on
for more than 3/4 mile (1.2 km).
152

{CAUTION:
Cruise control can be dangerous where
you cannot drive safely at a steady speed.
So, do not use your cruise control on
winding roads or in heavy traffic.
Cruise control can be dangerous on
slippery roads. On such roads, fast
changes in tire traction can cause
excessive wheel slip, and you could lose
control. Do not use cruise control on
slippery roads.
If your vehicle is in cruise control when the
Traction Control System (TCS), if your vehicle
has this feature, begins to limit wheel spin,
the cruise control will automatically disengage.
SeeTraction Control System (TCS) on page 294.
When road conditions allow you to safely use
it again, the cruise control can be turned back on.The cruise control
buttons are located on
left side of the
steering wheel.
T(On/Off):Press this button to turn cruise
control on and off. The indicator will be lit
when cruise control is on.
+ RES (Resume/Accelerate):Press this button
to make the vehicle accelerate or resume to
a previously set speed.
SET–:Press this button to set the speed or make
the vehicle decelerate.
[(Cancel):Press this button to cancel
cruise control.
155

Setting Cruise Control
Cruise control will not work if the parking brake is
set, or if the master cylinder brake uid level is low.
The cruise control light on the instrument panel
cluster will come on after the cruise control
has been set to the desired speed. SeeInstrument
Panel Cluster on page 180.
{CAUTION:
If you leave your cruise control on when
you are not using cruise, you might hit a
button and go into cruise when you do not
want to. You could be startled and even
lose control. Keep the cruise control switch
off until you want to use cruise control.
1. Press the cruise control on/off button.
2. Get up to the speed you want.
3. Press and release the SET– button located on
the steering wheel.
4. Take your foot off the accelerator.
Resuming a Set Speed
Suppose you set the cruise control at a desired
speed and then you apply the brake. This shuts
off the cruise control, but it does not need to
be reset.
Once you are driving about 25 mph (40 km/h) or
more, press the +RES button on the steering
wheel. The vehicle will go back to your chosen
speed and stay there.
Increasing Speed While Using Cruise
Control
To increase the cruise speed while using
cruise control:
Press and hold the +RES button on the
steering wheel until you reach your new
desired speed, then release it.
To increase vehicle speed in small increments,
press the +RES button.
156

Reducing Speed While Using Cruise
Control
To reduce your speed while using cruise control:
Press and hold the SET– button on the
steering wheel until you reach the lower speed
you want, then release it.
To slow down in very small amounts, press
the SET– button on the steering wheel
briey. Each time this is done, you will go
about 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase vehicle
speed. When you take your foot off the pedal, the
vehicle will slow down to the cruise speed you
set earlier.
Using Cruise Control on Hills
How well the cruise control will work on hills
depends upon the vehicle speed, load and the
steepness of the hills. When going up steep hills,
you may have to step on the accelerator pedal
to maintain your speed. When going downhill, you
may have to brake or shift to a lower gear to
keep your speed down. Of course, applying the
brake ends the cruise control. Many drivers
nd this to be too much trouble and do not use
cruise control on steep hills.
Ending Cruise Control
There are three ways to end cruise control:
Step lightly on the brake pedal.
Press the[(cancel) button on the
steering wheel.
Press theT(on/off) button on the
steering wheel.
Erasing Speed Memory
The cruise control set speed memory is erased by
turning off the cruise control or the ignition.
157

When it is dark enough outside, the DRL will turn
off and the vehicle’s headlamps and parking
lamps will turn on. The other lamps that come on
with the headlamps will also come on.
When it is bright enough outside, the headlamps
will go off and the DRL will come on.
To idle the vehicle with the DRL off, turn the
exterior lamp control off and then do one of the
following:
Turn the exterior lamp control to the parking
lamp position.
Turn the exterior lamp control to the
headlamp position.
Turn the exterior lamp control from AUTO to
off and back to AUTO.
This feature is not available for vehicles rst sold
in Canada.
To turn off the automatic headlamp feature when it
is dark outside, move the exterior lamp control
to the parking lamp position. The parking lamps
remain on and the headlamps turn off. The
fog lamps also go on if they were on previously.
As with any vehicle, the regular headlamp system
should be turned on when needed.
Fog Lamps
If your vehicle has fog
lamps, the button is
located in the center of
the exterior lamps
control on the left side
of the steering column.
Press the fog lamps button to turn the lamps
on or off.
While the high-beam headlamps are on, the fog
lamps are off.
Some localities have laws that require the
headlamps to be on along with the fog lamps.
Exterior Lighting Battery Saver
If the parking lamps or headlamps have been left
on after the ignition has been turned to off, the
exterior lamps will turn off after about 10 minutes.
This protects the battery from being drained.
Use the exterior lamp control to turn the lamps
back on, if they are still needed.
160

Interior Lamps
Your interior lamps
control is located next to
the exterior lamps
control and to the left of
the steering wheel on
the instrument panel.
9(Off):Turn the control to this position to
disable courtesy lamps, entry lighting, delayed
entry lighting, and delayed exit lighting.
1(Door):Turn the control to this position to turn
the interior lamps on when any door is open and
when the ignition key is removed from the ignition.
+(On):Turn the control to this position to turn
on the interior lamps.
The interior lamps can be controlled, or
automatically turned on or off under certain
conditions. They are explained in the following text.
Instrument Panel Brightness
The instrument panel lights can be brightened or
dimmed by pressing the center knob of the
interior lamp controls until it pops out. Turn the
knob clockwise to brighten the lights or
counterclockwise to dim them.
Courtesy Lamps
Courtesy lamps come on to make it easier to
enter and exit the vehicle. These lamps will come
on when the interior lamp control is in the door
position and any door is opened.
Entry Lighting
The courtesy lamps will come on and stay on for a
set time whenever the interior lamp control is in
the door position and the UNLOCK button on
the Remote Keyless Entry (RKE) transmitter is
pressed.
The lamps will stay on while a door is opened and
then turn off automatically about 25 seconds
after it is closed. If the UNLOCK button is pressed
and a door is not opened, the lamps will turn off
after about 25 seconds.
161

SERVICE VARIABLE EFFORT
STEERING
If your vehicle has variable effort steering, this
message displays when if this system is not
functioning properly. SeeSteering on page 297for
more information. Have the system serviced by
your dealer as soon as possible.
This message displays only while the ignition is in
RUN. Press any of the DIC buttons to acknowledge
this message and to clear it from the screen.
This message continues to display for two seconds
if it has not been acknowledged when the engine is
turned off. It also re-displays for two seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message re-appears
when the engine is turned on.
SERVICE VEHICLE SOON
This message displays when a non-emissions
related malfunction occurs. Have the vehicle
serviced by your dealer as soon as possible.This message displays only while the ignition is in
RUN. Press any of the DIC buttons to acknowledge
this message and to clear it from the screen.
This message continues to display for two seconds
if it has not been acknowledged when the engine is
turned off. It also re-displays for two seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message re-appears
when the engine is turned on.
STABILITY CONTROL ACTIVE
If your vehicle has StabiliTrak®, this message
displays when StabiliTrak®is actively assisting you
with directional control of the vehicle. Slippery
road conditions may exist when this message is
displayed, so adjust your driving accordingly.
SeeStabiliTrak
®System on page 296.
This message displays only while the ignition is in
RUN. This message stays on until road conditions
change and StabiliTrak
®is not active.
This message cannot be acknowledged and
cleared from the screen.
226