manual radio set BUICK LACROSSE 2008 Owner's Manual
[x] Cancel search | Manufacturer: BUICK, Model Year: 2008, Model line: LACROSSE, Model: BUICK LACROSSE 2008Pages: 440
Page 204 of 440
TRUNK AJAR
This message displays when the trunk is not closed
completely. Make sure that the trunk is closed
completely. SeeTrunk on page 2-14.
This message displays while the ignition is in ON/RUN.
A chime sounds when the gear position is shifted out of
PARK (P). Press any of the DIC buttons to acknowledge
this message and to clear it from the screen.
This message continues to display for two seconds if it
has not been acknowledged when the engine is
turned off. It also re-displays for two seconds if the
message has been acknowledged, but the condition still
exists when the engine is turned off.
If the condition still exists, the message re-appears
when the engine is turned on.
TURN SIGNAL ON
This message displays as a reminder to turn off the turn
signal if you drive your vehicle for more than about
0.75 mile (1.2 km) with a turn signal on. SeeTurn
Signal/Multifunction Lever on page 3-7.
This message displays and a chime sounds only when
the ignition is in ON/RUN. This message clears from
the DIC if the turn signal is manually turned off, a turn is
completed, or the message is acknowledged.
DIC Vehicle Personalization
Your vehicle may have customization capabilities that
allow you to program certain features to one preferred
setting. Customization features can only be programmed
to one setting on the vehicle and cannot be programmed
to a preferred setting for two different drivers. The
customization features include the following:
Exterior lighting delay
Interior lighting delay
Delayed locking
Content theft
Remote keyless entry feedback
Remote start
Your vehicle may also have personalization capabilities
that allow you to program certain features to a
preferred setting for up to two drivers. The rst
personalized key corresponds to driver 1 and the second
personalized key corresponds to driver 2. The
personalization features include the following:
Radio station presets
Auto door unlock preferences
Remote keyless entry unlock preferences
3-76
Page 216 of 440
To scan preset stations, press and hold either arrow for
more than four seconds. PSCAN or PSC displays
and the radio beeps twice. The radio goes to a preset
station, plays for a few seconds, then goes to the
next preset station. Press either arrow again or one of
the pushbuttons to stop scanning presets.
The radio seeks and scans stations only with a strong
signal that are in the selected band.
SCAN:Press until SC displays. The radio goes to a
station, plays for a few seconds, and then goes to
the next station. Press again to stop scanning stations.
The radio scans stations only with a strong signal
that are in the selected band.
INFO (Information) (XM™ Satellite Radio Service
Only):Your vehicle’s radio may have an INFO button.
If the current station on the radio has a message,
the information symbol displays. Press to see the
message. If the entire message is not displayed, parts
of the message appears every three seconds. To
manually scroll through the message, press and release
the INFO button.
When a message is not available from a station, NO
INFO displays.Setting Preset Stations
Up to 30 stations (six FM1, six FM2, six AM, six XM1™
and six XM2™ (if equipped)) can be programmed on
the six numbered pushbuttons.
To program either radio:
1. Turn the radio on.
2. Press BAND to select FM1, FM2, AM, or XM1™ or
XM2™ (if equipped).
3. Tune to the desired station.
4. Press EQ to select the equalization.
5. Press and hold one of the six numbered
pushbuttons until the radio beeps once. When that
numbered pushbutton is pressed again, the
station and equalization that were stored, returns.
6. Repeat the steps for each pushbutton.
Setting the Tone (Bass/Treble)
e
(Bass/Treble):Press and release until BASS or
TREBLE displays. Turn this knob to increase or to
decrease the bass or treble.
Press and hold to adjust the bass and treble to the
middle position. The radio beeps once.
3-88
Page 217 of 440
To adjust all tone and speaker controls to the middle
position, press and hold when no tone or speaker control
displays. ALL CENTERED displays and the radio
beeps once.
EQ (Equalization):Press to select customized
equalization settings.
To return the bass and treble to the manual mode,
press and release until BASS or TREBLE displays.
Adjusting the Speakers (Balance/Fade)
e
(Balance/Fade):To adjust the balance between
the right and the left speakers, press and release until
BAL (balance) displays. Turn this knob to move the
sound toward the right or the left speakers.
To adjust the fade between the front and the rear
speakers, press and release until FAD (fade) displays.
Turn this knob to move the sound toward the front
or the rear speakers.
To adjust the balance and the fade to the middle position,
press, then press and hold until the radio beeps once.
To adjust all tone and speaker controls to the middle
position, press and hold when no tone or speaker control
displays. ALL CENTERED displays and the radio
beeps once.
Finding a Category (CAT) Station
(XM™ Satellite Radio Service Only)
To select and nd a desired category, perform
the following:
1. Press the CAT button to enter the category select
mode. The current category displays.
2. Turn the
eknob to select a category.
3. Once the desired category is displayed, press either
SEEK arrow to go to the category’s rst station.
4. Press either SEEK arrow again to go to another
station within that category. The category will
display. If CAT times out and is no longer on the
display, go back to Step 1.
5. Press CAT to exit the category select mode or wait
for CAT to time out.
If the radio cannot nd the desired category, NOT
FOUND displays and the radio returns to the last station
you were listening to.
3-89