tire pressure reset BUICK LESABRE 2000 Owner's Manual
[x] Cancel search | Manufacturer: BUICK, Model Year: 2000, Model line: LESABRE, Model: BUICK LESABRE 2000Pages: 381, PDF Size: 2.59 MB
Page 139 of 381
yellowblue
2-82
GAGE INFO: Use this button to display oil pressure,
oil life, coolant temperature, tire pressure and
battery information.
Press the GAGE INFO button until OIL PRESSURE
appears in the display. If there are no problems
detected with the oil pressure, the display will show
OIL PRESSURE NORMAL. If a low oil pressure
condition is detected, the display will show OIL
PRESSURE LOW. If you see the OIL PRESSURE
LOW message, your vehicle could be low on oil or
the oil is not going through the engine properly.
See your dealer for service.
Press the GAGE INFO button until COOLANT
TEMP appears in the display. If there are no
problems detected with the temperature, COOLANT
TEMP NORMAL will appear in the display. If the
temperature is too high, COOLANT TEMP HOT
will appear in the display. If you see the COOLANT
TEMP HOT message, the engine is overheated. You
should pull off the road, stop your vehicle and turn
off your engine as soon as possible. This manual
explains what to do. See ªEngine Overheatingº in
the Index.Press the GAGE INFO button until the display
shows BATTERY STATE. If the voltage is normal
the display will show BATTERY STATE NORMAL.
If the voltage drops below 10.5 volts, the display will
show BATTERY STATE LOW. If the voltage is
above 16 volts, the display will show BATTERY
STATE HIGH. If the display shows the high or low
message, you need to have your battery and charging
system checked.
Press the GAGE INFO button until OIL LIFE
INDEX appears in the display. The OIL LIFE
INDEX NORMAL display will show an estimate of
the oil's remaining useful life. When the oil life
index is less than 10%, the display will show OIL
LIFE INDEX CHANGE OIL. When you have the
oil changed according to the maintenance schedule
(see ªMaintenance Scheduleº in the Index), you will
have to reset the oil life monitor. To reset the Oil
Life System (Index), see ªOil Life Systemº or
ªEngine Oil, When to Changeº in the Index.
Page 140 of 381
yellowblue
2-83
Press the GAGE INFO button until TIRE PRESSURE
appears in the display. TIRE PRESSURE NORMAL is
displayed when the Check Tire Pressure System
believes your vehicle's tire pressures are normal. If a
potential tire pressure problem is detected, the display
will show TIRE PRESSURE LOW: CHECK TIRES.
If you see the TIRE PRESSURE LOW: CHECK
TIRES message, you should stop as soon as you can
and check all your tires for damage. (If a tire is flat, see
ªIf a Tire Goes Flatº in the Index.) Also check the
tire pressure in all four tires as soon as you can.
See ªInflation
-- Tire Pressureº and ªCheck Tire
Pressure Systemº in the Index. There are times
when you will have to reset (calibrate) the Check
Tire Pressure System. See ªCheck Tire Pressure
Systemº in the Index.
RESET: This button, used along with other buttons,
will reset system functions.
ENG/MET: Use this button to change the display
between English and metric units.
DIC Warnings and Messages
Other messages or warnings may appear in the DIC
display. For Canadian drivers, in addition to the DIC
message your DIC will display EXP with a number after
it which reflects the following messages:EXP (Export ID) Warning Message
2 ENG COOLANT LOW
- CHECK LEVEL . . . . . .
20 TURN SIGNAL STILL ON?. . . . . . . . . . . . . . . .
24 TRUNK AJAR. . . . . . . . . . . . . . . . . . . . . . . . . . .
25 WINDSHIELD WASHER FLUID LOW. . . . . . .
27 BATTERY SAVER ACTIVE. . . . . . . . . . . . . . . .
36 ENGINE OIL LOW
- CHECK LEVEL . . . . . . . .
40 THEFT ATTEMPT DETECTED. . . . . . . . . . . . .
54 SERVICE STABILITY SYSTEM. . . . . . . . . . . .
55 STABILITY SYSTEM ACTIVE. . . . . . . . . . . . .
61 GAS CAP LOOSE
- CHECK CAP . . . . . . . . . . .
81 CHANGE ENGINE OIL SOON. . . . . . . . . . . . .
91 TRACTION CONTROL SYSTEM ACTIVE. . .
102 CHECK CHARGE SYSTEM. . . . . . . . . . . . . . .
139 DOOR AJAR. . . . . . . . . . . . . . . . . . . . . . . . . . .
144 CHECK TIRE PRESSURE. . . . . . . . . . . . . . . .
The EXP codes are used to make translation from
English to other languages easier.
Pressing any of the DIC control buttons will remove the
messages or warnings from the DIC display.
Page 303 of 381
yellowblue
6-44
If the anti-lock brake system warning light comes on,
the check tire pressure system may not be working
properly. See your dealer for service. (Also, see
ªAnti
-Lock Brake System Warning Lightº in the Index.)
The check tire pressure system detects differences
in tire rotation speeds that are caused by changes in tire
pressure. The system can alert you about a low
tire
-- but it doesn't replace normal tire maintenance.
See ªTiresº in the Index.
When the TIRE PRESSURE LOW: CHECK TIRES
message appears on the Driver Information Center, you
should stop as soon as you can and check all your tires
for damage. (If a tire is flat, see ªIf a Tire Goes Flatº in
the Index.) Also check the tire pressure in all four tires
as soon as you can. See ªInflation
-Tire Pressureº
in the Index.
Any time you adjust a tire's pressure or have one or
more tires repaired or replaced, you'll need to reset
(calibrate) the check tire pressure system. You'll also
need to reset the system whenever you rotate the tires,
buy new tires, install or remove the compact spare, and
whenever the vehicle's battery has been disconnected.Don't reset the check tire pressure system without first
correcting the cause of the problem and checking and
adjusting the pressure in all four tires. If you reset the
system when the tire pressures are incorrect, the check
tire pressure system will not work properly and may not
alert you when a tire is low or high.
To reset (calibrate) the system:
1. Turn the ignition switch to RUN.
2. Press the GAGE INFO button on the DIC until
TIRE PRESSURE appears on the display.
3. Press and hold the DIC RESET button for about
five seconds. After five seconds, the display will
show TIRE PRESSURE RESET. If TIRE
PRESSURE RESET does not appear in the display
after about five seconds retry the process. If it does
not work after two tries, see your dealer for service.
After you release the DIC RESET button, TIRE
PRESSURE NORMAL will appear in the display.
The system completes the calibration process during
driving. Calibration time can take 45 to 90 minutes,
depending on your driving habits. After the system has
been calibrated, the system will alert the driver that a tire
is low, up to a maximum speed of 65 mph (105 km/h).
Page 304 of 381
yellowblue
6-45 Tire Inspection and Rotation
Tires should be rotated every 6,000 to 8,000 miles
(10 000 to 13 000 km). Any time you notice unusual wear,
rotate your tires as soon as possible and check wheel
alignment. Also check for damaged tires or wheels. See
ªWhen It's Time for New Tiresº and ªWheel
Replacementº later in this section for more information.
The purpose of regular rotation is to achieve more uniform
wear for all tires on the vehicle. The first rotation is the
most important. See ªScheduled Maintenance Servicesº in
the Index for scheduled rotation intervals.
When rotating your tires, always use the correct rotation
pattern shown here.Don't include the compact spare tire in your tire rotation.
After the tires have been rotated, adjust the front and
rear inflation pressures as shown on the Tire
-Loading
Information label. Reset the Make certain that all wheel
nuts are properly tightened. See ªWheel Nut Torqueº in
the Index.
CAUTION:
Rust or dirt on a wheel, or on the parts to which
it is fastened, can make wheel nuts become loose
after a time. The wheel could come off and cause
an accident. When you change a wheel, remove
any rust or dirt from places where the wheel
attaches to the vehicle. In an emergency, you can
use a cloth or a paper towel to do this; but be
sure to use a scraper or wire brush later, if
you need to, to get all the rust or dirt off.
(See ªChanging a Flat Tireº in the Index.)