BUICK LESABRE 2002 Owner's Manual

2-88
If you choose ON for AUTO DOOR LOCKS, ON for
UNLOCK and PARK, your doors will lock every time
you shift out of PARK (P), and the doors will unlock
every time you stop and shift into PARK (P).
If you choose ON for AUTO DOOR LOCKS, and OFF
for UNLOCK, your doors will lock every time you shift
out of PARK (P), and there will be no automatic door
unlock when shifting back into PARK (P).
If you choose ON for UNLOCK and DRIVER for
DOOR TO UNLOCK, only the driver's door will
automatically unlock when shifting into PARK or
turning the key to OFF.
If you choose ON for UNLOCK and ALL for DOOR
TO UNLOCK, all doors will automatically unlock when
shifting into PARK or turning the key to OFF.
To change modes, do the following:
1. Move the arrow on the display between the
selections by pressing the ENG/MET button.
2. Once you have made your selection, press the
RESET button and your choice will be retained
in memory.
See ªAutomatic Door Locksº in the Index for more
information about this feature.Window Lockout
The number of passenger windows locked out by
the window LOCK switch can be programmed through
the DIC.
If you choose R + PASS, all three passenger window
switches will be inactive when the window LOCK
switch is enabled.
If you choose REAR, only the two rear passenger
window switches will be locked out when the window
LOCK switch is enabled.
To change modes, do the following:
1. Move the arrow on the display between R + PASS
and REAR by pressing the ENG/MET button.
2. Once you have made your selection, press
the RESET button. Your choice will be retained
in memory.
For more information on this feature, see ªWindow
Lockº in the Index.

2-89
Security Feedback
By choosing different combinations of these selections,
you can choose the type of transmitter activated
feedback when locking and unlocking your vehicle with
your transmitter. Each time you make a selection by
pressing the ENG/MET button, press the RESET
button to record your choice.

KEYLESS FEEDBACK
-- OFF/ON

LIGHTS FEEDBACK
-- OFF/ON

HORN FEEDBACK
-- OFF/ON
If you choose ON for KEYLESS FEEDBACK you will
also need to choose LIGHTS and/or HORN FEEDBACK.
You can select the following modes:

If you choose OFF for KEYLESS FEEDBACK,
you will receive no security feedback when locking
or unlocking your vehicle.

If you choose ON for KEYLESS FEEDBACK
and ON for LIGHTS FEEDBACK, the exterior
lamps will flash twice when unlocking your vehicle
and once when locking your vehicle.
If you choose ON for KEYLESS FEEDBACK
and ON for HORN FEEDBACK, your horn will
chirp when all doors are unlocked and when locking
your vehicle.

If you choose ON for KEYLESS, LIGHTS and
HORN FEEDBACK, your exterior lamps will flash
twice at the first unlock button press, your exterior
lamps will flash twice and the horn will chirp once at
the second unlock button press, and the exterior
lamps will flash and the horn will chirp once when
locking your vehicle.
For more information on this feature, see ªSecurity
Feedbackº in the Index.
Delayed Locking
This feature, which delays the actual locking of the
vehicle, can be made active or inactive through the DIC.
When DELAYED LOCKING
-- OFF/ON appears on
the display, use the ENG/MET button to toggle the
arrow between OFF and ON. When you have made your
choice, press the RESET button to record your selection.
For more information on this feature, see ªDelayed
Lockingº in the Index.

2-90
Perimeter Lighting
When the button with the unlock symbol on the remote
keyless entry transmitter is pressed, the DRL
(high
-beams at reduced intensity), parking lamps and
back
-up lamps will turn on if it is dark enough
according to the Twilight Sentinel.
You can control activation of this feature by choosing
OFF or ON when the PERIMETER LIGHTS choice is
displayed on the DIC. Make your choice by pressing the
ENG/MET button and record your choice by pressing
the RESET button. You will then be prompted to choose
a TIMEOUT period. See ªExterior Lightsº following for
more information.
For more information on this feature, see ªPerimeter
Lightingº in the Index.
Exterior Lights
The EXTERIOR LIGHTS/TIMEOUT feature can be
changed to a desired setting by using the ENG/MET to
toggle from 5 to 30 seconds. Each toggle will increase
the time by five seconds. Once the desired timeout is
displayed, press RESET to record your choice and move
on to the next personal choice feature.Memory Seat Recall (If Equipped)
This feature recalls the position of your seat. When this
feature is active, the memory seat and mirror positions
will be recalled for the identified driver when the remote
keyless entry transmitter is used to enter the vehicle.
You can program this feature to be active by choosing
ON when the SEAT RECALL choice appears, or
inactive by choosing OFF when the SEAT RECALL
choice appears on the DIC. Make your choices by
pressing the ENG/MET button and store them to
memory by pressing the RESET button.
You can also program this feature to recall your memory
seat position or the exit seat position.
MEMORY: Choose ON when the SEAT RECALL
choice appears, and then choose MEMORY when the
RECALL POSITION choice appears.

2-91
EXIT: Choose ON when the SEAT RECALL choice
appears, and then choose EXIT when the RECALL
POSITION choice appears. The seat will move when
you enter the vehicle after unlocking it with a remote
keyless entry transmitter. This will allow for easy entry.
For more information on this feature, see ªMemory
Seatsº in the Index.
Parallel Park Assist (If Equipped)
The parallel park assist mirror, which tips the passenger
mirror down while the vehicle is in REVERSE (R), can
be made active or inactive through the DIC. When TILT
MIRRORS
-- OFF/ON appears on the display, use the
ENG/MET button to toggle the arrow between OFF and
ON. When you have made your choice, press the
RESET button to record your selection. For more
information on this feature, see ªParallel Park Assist
Mirrorº in the Index.Driver ID
This feature displays the DRIVER ID, as identified by
the DIC. If this feature is ON, the DRIVER ID will
be displayed every time the ignition is turned on. If the
DRIVER ID is OFF, the DRIVER ID can be displayed
by pressing either a button on the remote keyless entry
transmitter or a memory seat button.
Language Selection
After DRIVER ID has been selected, ªLanguage
Englishº will be displayed. Pressing the RESET
button selects English as the DIC language and ends
programming. Pressing the ENG/MET button will bring
up the display ªLangue Fran†ais.º Pressing the RESET
button selects French as the DIC language. Pressing the
ENG/MET button will bring up the display ªIdioma
Espanol.º Pressing the RESET button selects Spanish
as the DIC language. Pressing the ENG/MET button
will return you to the ªLanguage Englishº display
and allows you to start the process of language
selection again.

2-92
Head-Up Display (HUD)
(If Equipped)
CAUTION:
If the HUD image is too bright, or too high in
your field of view, it may take you more time to
see things you need to see when it's dark outside.
Be sure to keep the HUD image dim and placed
low in your field of view.
If your vehicle is equipped with the Head-Up Display
(HUD), you can see some of the driver information
that appears on your instrument panel cluster.
The information may be displayed in English or metric
units and appears as a reflection in the windshield.
The HUD consists of the following information:

Speedometer Reading

Turn Signal Indicators

High
-Beam Headlamp Indicator

Check Gages Message
The HUD shows these images when they are lighted on
the instrument panel cluster.

2-93
Be sure to continue scanning your displays, controls and
driving environment just as you would in a vehicle
without HUD. If you never look at your instrument
panel cluster, you may not see something important,
such as a warning light.
NOTICE:
Although the HUD image appears to be near the
front of the vehicle, do not use it as a parking aid.
The HUD was not designed for that purpose. If
you try to use the display as a marker for the
front of your vehicle, such as in a parking lot, you
may misjudge distance and hit an obstacle or
another vehicle.
The HUD controls are located on the instrument panel to
the left of the steering wheel.
1. Start your engine and slide the HUD dimmer lever
all the way up.
The brightness of the HUD image is determined by
an internal photo
-cell, and where you have the HUD
dimmer control set.
2. Adjust the seat to your driving position. Press the
image height adjuster switch to raise the image as far
as possible.

2-94
3. Now press the image height adjuster switch to
position the image as low as possible, while still
keeping it in full view.
4. Slide the dimmer lever downward until the HUD
image is no brighter than necessary.
To turn the HUD display off, slide the dimmer lever
all the way down.
If the sun comes out and the sky becomes cloudy,
you may need to adjust the HUD brightness using
the dimmer lever. Polarized sunglasses could make
the HUD image harder to see.
To change the display from English to metric units,
push the ENG/MET button located to the left of the
steering column.
Clean the inside of the windshield as necessary to
remove any dirt or film that reduces the sharpness
or clarity of the HUD image.To clean the HUD lens, spray household glass cleaner
on a soft, clean cloth. Gently wipe and dry the HUD
lens. Do not spray cleaner directly on the lens to avoid
cleaner leaking inside the unit.
If the ignition is on and you can't see the HUD image,
check to see if:

Something is covering the HUD unit.

The HUD dimmer lever is adjusted properly.

The HUD image is adjusted to the proper height.

A fuse is blown. See ªFuses and Circuit Breakersº
in the Index.
Keep in mind that your windshield is part of the HUD
system. If you ever have to have your windshield
replaced, be sure to get one that is designed for HUD
or your HUD image may look blurred or out of focus.

3-
3-1
Section 3 Comfort Controls and Audio Systems
In this section, you'll find out how to operate the comfort control and audio systems offered with your vehicle.
Be sure to read about the particular systems supplied with your vehicle.
3
-2 Comfort Controls
3
-2 Electronic Touch Climate Control
3
-4 Dual Automatic ComforTemp
Climate
Control (If Equipped)
3
-6 Passenger Climate Control (If Equipped)
3
-7 Personal Choice Comfort Controls
(If Equipped)
3
-8 Air Conditioning
3
-9 Heating
3
-10 Defogging and Defrosting
3
-10 Rear Window Defogger
3
-11 Ventilation System
3
-12 Steering Wheel Controls for Climate Control
(If Equipped)
3
-13 Audio Systems
3
-13 Setting the Clock
3
-13 AM-FM Stereo with Cassette Tape Player
(If Equipped)3
-19 AM-FM Stereo with Compact Disc
Player with Automatic Tone Control and
Radio Data Systems (RDS) (If Equipped)
3
-26 AM-FM Stereo with Cassette Tape and
Compact Disc Player with Automatic Tone
Control and Radio Data Systems (RDS)
(If Equipped)
3
-35 Trunk-Mounted CD Changer (Option)
3
-39 Personal Choice Radio Controls (If Equipped)
3
-40 Theft-Deterrent Feature (If Equipped)
3
-40 Audio Steering Wheel Controls (If Equipped)
3
-41 Understanding Radio Reception
3
-41 Tips About Your Audio System
3
-42 Care of Your Cassette Tape Player
3
-43 Care of Your Compact Discs
3
-43 Care of Your Compact Disc Player
3
-44 Diversity Antenna System
3
-44 Chime Level Adjustment

3-2
Comfort Controls
This section describes how to operate your climate
control system. With this system, you can control the
heating, cooling and ventilation in your vehicle.
Your vehicle also has a flow
-through ventilation system
described later in this section.
Electronic Touch Climate Control
Fan Lever
The FAN lever is used to select the speed of the fan.
Moving the lever between LOW and HIGH will
decrease or increase the fan speed. The fan will be
off when the system is off.Temperature Lever
This lever is used to adjust the temperature of the air
coming through the system. Move the TEMPERATURE
lever between COOL and WARM to change the
temperature of the air coming through your outlets.
Mode Controls
The buttons on your system allow you to choose settings
to deliver air through the floor ducts, instrument panel
outlets or windshield outlets.
RECIRC (Recirculation): Press this button to limit the
amount of outside air entering your vehicle. This is
helpful when you are trying to cool the interior of the
vehicle quickly, or limit the amount of outside air
entering your vehicle. To turn off RECIRC, press the
button again. If you select FRONT defrost or BLEND
while RECIRC is selected, the system will automatically
turn off RECIRC to prevent fogging. If you select
RECIRC while in FRONT defrost, the RECIRC light
will flash three times to let you know this is not allowed.

3-3
VENT: This setting directs outside air through the
instrument panel outlets. The air conditioning
compressor is not working when VENT is selected. If
you select VENT while in FRONT defrost, the VENT
light will flash three times to let you know this is not
allowed. This is to prevent fogging.
HTR (Heater): This setting directs most of the air
out of the floor ducts while some air will flow through
the windshield and side window outlets. The air
conditioning compressor is not working when
HTR is selected.
BLEND: When BLEND is selected, the airflow will be
split between the windshield outlets and the floor ducts.
The air conditioning compressor will be operating.
FRONT: This setting directs most of the airflow
toward the windshield.
OFF: The ventilation system always allows fresh air to
flow through your vehicle when it is moving. The
system will try to keep the air at a previously chosen
temperature. When the system is off, the blower fan is
also off.MAX (Maximum Air Conditioning): This setting
directs airflow through the instrument panel outlets. The
amount of outside air entering your vehicle is limited
with this setting. The air conditioning compressor is on
in this mode.
Also in this mode, the RECIRC function is activated
to create the maximum cooling effect in the vehicle. If
RECIRC was active before selecting MAX, the light in
the RECIRC button will go off. If RECIRC is selected
after MAX, the light in the RECIRC button will not
come on.
NORM (Normal): This setting cools the outside
air entering your vehicle and directs it through the
instrument panel outlets. The air conditioning
compressor is on in this mode.
BI
-LEV (Bi-Level): This setting directs warmer air
to the floor ducts and cooler air to the instrument panel
outlets. The air conditioning compressor is on in
this mode.