reset BUICK LESABRE 2002 User Guide

2-85 DIC Warnings and Messages
Other messages or warnings may appear in the DIC
display. For Canadian drivers, in addition to the DIC
message your DIC will display EXP with a number after
it which reflects the following messages:
EXP (Export ID) Warning Message
20 TURN SIGNAL STILL ON?. . . . . . . . . . . . . . . .
24 TRUNK AJAR. . . . . . . . . . . . . . . . . . . . . . . . . . .
25 WINDSHIELD WASHER FLUID LOW. . . . . . .
27 BATTERY SAVER ACTIVE. . . . . . . . . . . . . . . .
36 ENGINE OIL LOW
- CHECK LEVEL . . . . . . . .
40 THEFT ATTEMPT DETECTED. . . . . . . . . . . . .
54 SERVICE STABILITY SYSTEM. . . . . . . . . . . .
55 STABILITY SYSTEM ACTIVE. . . . . . . . . . . . .
61 GAS CAP LOOSE
- CHECK CAP . . . . . . . . . . .
81 CHANGE ENGINE OIL SOON. . . . . . . . . . . . .
91 TRACTION CONTROL SYSTEM ACTIVE. . .
102 CHECK CHARGE SYSTEM. . . . . . . . . . . . . . .
139 DOOR AJAR. . . . . . . . . . . . . . . . . . . . . . . . . . .
144 CHECK TIRE PRESSURES. . . . . . . . . . . . . . . The EXP codes are used to make translation from
English to other languages easier.
Pressing any of the DIC control buttons will remove
the messages or warnings from the DIC display.
SERVICE STABILITY SYSTEM
- 54 : If you ever
see the SERVICE STABILITY SYSTEM message,
it means there may be a problem with your stability
enhancement system. If you see this message, try to
reset the system (stop; turn off the engine; then start the
engine again). If the SERVICE STABILITY SYSTEM
message still comes on, it means there is a problem.
You should see your dealer for service. Reduce your
speed and drive accordingly.
STABILITY SYSTEM ACTIVE
- 55 : You may see
the STABILITY SYSTEM ACTIVE message on the
Driver Information Center. It means that an advanced,
computer
-controlled system has come on to help your
vehicle continue to go in the direction in which you're
steering. This stability enhancement system activates
when the computer senses that your vehicle is just
starting to spin, as it might if you hit a patch of ice or
other slippery spot on the road. When the system is on,
you may hear a noise or feel a vibration in the brake
pedal. This is normal.

2-87
Use the following steps for personal choice
programming instructions.
1. Turn the ignition on and keep the transaxle
in PARK (P).
2. Inform the DIC which driver you are by pressing
the button with the unlock symbol on your remote
keyless entry transmitter or the appropriate memory
seat control.
3. Press and hold the ENG/MET button for five
seconds. WELCOME TO BUICK OPTION
FEATURE will appear in the display.
4. The first choice to be made will be DRIVER ID 1
or 2. Press the ENG/MET button to toggle between
your selections within a display and RESET to
choose the current selection and move on to the
next personal choice feature.
If you would like to exit the selection mode without
moving through each of the personal choice features,
simply press a different button on the DIC or turn off the
ignition. Whatever personal choices you made will still
be retained, even without passing through each of the
features. In order for your personal choices to save, you
must press RESET after making your selections.If you happen to move past a selection you would like
to make a personal choice for, press the button with the
unlock symbol on your remote keyless entry transmitter
or press the appropriate driver number on the seat
control. This will return you to the beginning of the
option feature programming mode.
Automatic Door Locks
The door lock modes when shifting in and out of
PARK (P), can be changed through the DIC. You
can change these modes by different selections of the
following DIC displays:

AUTO DOOR LOCKS
-- OFF/ON

UNLOCK
-- OFF/ON

UNLOCK
-- KEY OFF/PARK

DOOR TO UNLOCK
-- DRIVER/ALL
If you choose OFF for AUTO DOOR LOCKS,
your door locks will operate normally with no
automatic feature.
If you choose ON for AUTO DOOR LOCKS, ON for
UNLOCK and KEY OFF, your doors will lock every
time you shift out of PARK (P), and the doors will
unlock every time you stop and turn the ignition to OFF.

2-88
If you choose ON for AUTO DOOR LOCKS, ON for
UNLOCK and PARK, your doors will lock every time
you shift out of PARK (P), and the doors will unlock
every time you stop and shift into PARK (P).
If you choose ON for AUTO DOOR LOCKS, and OFF
for UNLOCK, your doors will lock every time you shift
out of PARK (P), and there will be no automatic door
unlock when shifting back into PARK (P).
If you choose ON for UNLOCK and DRIVER for
DOOR TO UNLOCK, only the driver's door will
automatically unlock when shifting into PARK or
turning the key to OFF.
If you choose ON for UNLOCK and ALL for DOOR
TO UNLOCK, all doors will automatically unlock when
shifting into PARK or turning the key to OFF.
To change modes, do the following:
1. Move the arrow on the display between the
selections by pressing the ENG/MET button.
2. Once you have made your selection, press the
RESET button and your choice will be retained
in memory.
See ªAutomatic Door Locksº in the Index for more
information about this feature.Window Lockout
The number of passenger windows locked out by
the window LOCK switch can be programmed through
the DIC.
If you choose R + PASS, all three passenger window
switches will be inactive when the window LOCK
switch is enabled.
If you choose REAR, only the two rear passenger
window switches will be locked out when the window
LOCK switch is enabled.
To change modes, do the following:
1. Move the arrow on the display between R + PASS
and REAR by pressing the ENG/MET button.
2. Once you have made your selection, press
the RESET button. Your choice will be retained
in memory.
For more information on this feature, see ªWindow
Lockº in the Index.

2-89
Security Feedback
By choosing different combinations of these selections,
you can choose the type of transmitter activated
feedback when locking and unlocking your vehicle with
your transmitter. Each time you make a selection by
pressing the ENG/MET button, press the RESET
button to record your choice.

KEYLESS FEEDBACK
-- OFF/ON

LIGHTS FEEDBACK
-- OFF/ON

HORN FEEDBACK
-- OFF/ON
If you choose ON for KEYLESS FEEDBACK you will
also need to choose LIGHTS and/or HORN FEEDBACK.
You can select the following modes:

If you choose OFF for KEYLESS FEEDBACK,
you will receive no security feedback when locking
or unlocking your vehicle.

If you choose ON for KEYLESS FEEDBACK
and ON for LIGHTS FEEDBACK, the exterior
lamps will flash twice when unlocking your vehicle
and once when locking your vehicle.
If you choose ON for KEYLESS FEEDBACK
and ON for HORN FEEDBACK, your horn will
chirp when all doors are unlocked and when locking
your vehicle.

If you choose ON for KEYLESS, LIGHTS and
HORN FEEDBACK, your exterior lamps will flash
twice at the first unlock button press, your exterior
lamps will flash twice and the horn will chirp once at
the second unlock button press, and the exterior
lamps will flash and the horn will chirp once when
locking your vehicle.
For more information on this feature, see ªSecurity
Feedbackº in the Index.
Delayed Locking
This feature, which delays the actual locking of the
vehicle, can be made active or inactive through the DIC.
When DELAYED LOCKING
-- OFF/ON appears on
the display, use the ENG/MET button to toggle the
arrow between OFF and ON. When you have made your
choice, press the RESET button to record your selection.
For more information on this feature, see ªDelayed
Lockingº in the Index.

2-90
Perimeter Lighting
When the button with the unlock symbol on the remote
keyless entry transmitter is pressed, the DRL
(high
-beams at reduced intensity), parking lamps and
back
-up lamps will turn on if it is dark enough
according to the Twilight Sentinel.
You can control activation of this feature by choosing
OFF or ON when the PERIMETER LIGHTS choice is
displayed on the DIC. Make your choice by pressing the
ENG/MET button and record your choice by pressing
the RESET button. You will then be prompted to choose
a TIMEOUT period. See ªExterior Lightsº following for
more information.
For more information on this feature, see ªPerimeter
Lightingº in the Index.
Exterior Lights
The EXTERIOR LIGHTS/TIMEOUT feature can be
changed to a desired setting by using the ENG/MET to
toggle from 5 to 30 seconds. Each toggle will increase
the time by five seconds. Once the desired timeout is
displayed, press RESET to record your choice and move
on to the next personal choice feature.Memory Seat Recall (If Equipped)
This feature recalls the position of your seat. When this
feature is active, the memory seat and mirror positions
will be recalled for the identified driver when the remote
keyless entry transmitter is used to enter the vehicle.
You can program this feature to be active by choosing
ON when the SEAT RECALL choice appears, or
inactive by choosing OFF when the SEAT RECALL
choice appears on the DIC. Make your choices by
pressing the ENG/MET button and store them to
memory by pressing the RESET button.
You can also program this feature to recall your memory
seat position or the exit seat position.
MEMORY: Choose ON when the SEAT RECALL
choice appears, and then choose MEMORY when the
RECALL POSITION choice appears.

2-91
EXIT: Choose ON when the SEAT RECALL choice
appears, and then choose EXIT when the RECALL
POSITION choice appears. The seat will move when
you enter the vehicle after unlocking it with a remote
keyless entry transmitter. This will allow for easy entry.
For more information on this feature, see ªMemory
Seatsº in the Index.
Parallel Park Assist (If Equipped)
The parallel park assist mirror, which tips the passenger
mirror down while the vehicle is in REVERSE (R), can
be made active or inactive through the DIC. When TILT
MIRRORS
-- OFF/ON appears on the display, use the
ENG/MET button to toggle the arrow between OFF and
ON. When you have made your choice, press the
RESET button to record your selection. For more
information on this feature, see ªParallel Park Assist
Mirrorº in the Index.Driver ID
This feature displays the DRIVER ID, as identified by
the DIC. If this feature is ON, the DRIVER ID will
be displayed every time the ignition is turned on. If the
DRIVER ID is OFF, the DRIVER ID can be displayed
by pressing either a button on the remote keyless entry
transmitter or a memory seat button.
Language Selection
After DRIVER ID has been selected, ªLanguage
Englishº will be displayed. Pressing the RESET
button selects English as the DIC language and ends
programming. Pressing the ENG/MET button will bring
up the display ªLangue Fran†ais.º Pressing the RESET
button selects French as the DIC language. Pressing the
ENG/MET button will bring up the display ªIdioma
Espanol.º Pressing the RESET button selects Spanish
as the DIC language. Pressing the ENG/MET button
will return you to the ªLanguage Englishº display
and allows you to start the process of language
selection again.

3-14
Finding a Station
AM FM: Press this button to switch between AM, FM1
and FM2. The display shows your selection.
TUNE: Turn this knob clockwise to tune to the next station.
Turn it counterclockwise to tune to the previous station.
SEEK : Press the right or left arrow to go to the
next or previous station and stay there. The sound will
mute while seeking. The radio will seek to stations with
a strong signal only.
To scan stations, press and hold one of the SEEK arrows
for two seconds and SCN will appear on the display.
The radio will go to a station, play for a few seconds,
then go on to the next station. Press one of the SEEK
arrows again to stop scanning. The sound will mute
while scanning. The radio will seek to stations with a
strong signal only.
To scan preset stations, press and hold one of the SEEK
arrows for more than four seconds until PSCAN and the
preset number appear on the display. You will hear a double
beep. The radio will go to the first preset station stored
on your pushbuttons, play for a few seconds, then go on to
the next preset station. Preset scan will only scan the
six presets that are in the band selected. Press one of the
SEEK arrows again to stop scanning your preset stations.
The radio will seek to stations with a strong signal only.Setting Preset Stations
The six numbered pushbuttons let you return to
your favorite stations. You can set up to 18 stations
(six AM, six FM1 and six FM2) by performing the
following steps:
1. Turn the radio on.
2. Press AM FM to select AM, FM1 or FM2.
3. Tune in the desired station.
4. Press EQ to select the EQ setting. It will be stored
with the preset station.
5. Press and hold one of the six numbered pushbuttons.
When you hear the radio produce one beep, release
the pushbutton. Whenever you press that numbered
pushbutton, the station you set will return.
6. Repeat the steps for each pushbutton.

3-20
To scan preset stations, press and hold one of the SEEK
arrows for more than four seconds until PSCAN and the
preset number appear on the display. You will hear a double
beep. The radio will go to the first preset station stored on
your pushbuttons, play for a few seconds, then go on to
the next preset station. Preset scan will only scan the six
presets that are in the band selected. Press one of the SEEK
arrows again to stop scanning your preset stations. The
radio will seek to stations with a strong signal only.
Setting Preset Stations
The six numbered pushbuttons let you return to your
favorite stations. You can set up to 18 stations (six AM,
six FM1 and six FM2) by performing the following steps:
1. Turn the radio on.
2. Press AM FM to select AM, FM1 or FM2.
3. Tune in the desired station.
4. Press EQ to select the EQ setting. It will be stored
with the preset station.
5. Press and hold one of the six numbered pushbuttons.
When you hear the radio produce one beep, release
the pushbutton. Whenever you press that numbered
pushbutton, the station you set will return.
6. Repeat the steps for each pushbutton.Setting the Tone (Bass/Treble)
AUDIO: Push and release AUDIO until BASS appears
on the display. Then turn the AUDIO knob clockwise to
increase bass. BASS and a positive number will appear
on the display. Turn the AUDIO knob counterclockwise
to decrease bass. BASS and a negative number will
appear on the display. BASS and a zero will appear on
the display when the bass level is set to the middle
position. Stop turning the knob when you find the bass
level you want or when the maximum or minimum level
is reached.
Push and release AUDIO until MID appears on the
display. Then turn the AUDIO knob clockwise to
increase treble. MID and a positive number will appear on
the display. Turn the AUDIO knob counterclockwise to
decrease treble. MID and a negative number will appear
on the display. MID and a zero will appear on the display
when the treble level is set to the middle position. Stop
turning the knob when you find the treble level you want
or when the maximum or minimum level is reached.

3-22
To adjust balance or fade to the middle position, select
BAL or FADE. Then push and hold AUDIO for more
than two seconds until you hear a beep. The indicator
will be centered on the display To adjust both tone
controls and both speaker controls to the middle
position, end out of audio mode by pushing the AUDIO
knob until the display goes blank. Then press and hold
AUDIO for more than two seconds until you hear a
beep. ALL CENTERED will appear on the display.
EQ (Equalizer): This feature allows you to choose
preset bass, mid and treble equalization settings
designed for different program types. Press EQ to select
the desired preset equalization setting. Each time you
press EQ, another setting will appear on the display.Using RDS
Your audio system is equipped with a Radio
Data System (RDS). With RDS, the radio can
do the following:

Seek only to stations with the types of programs you
want to listen to,

seek to stations with traffic announcements,

receive announcements concerning local and
national emergencies, and

receive and display messages from radio stations.
RDS features are only available for use on FM stations
which broadcast RDS information. The RDS features of
your radio rely upon receiving specific RDS information
from these stations. These features will only work when
the RDS information is available. In rare cases, a radio
station may broadcast incorrect information that will
cause the radio features to work improperly. If this
happens, contact the radio station.
When you are tuned to an RDS station, the station
name will appear on the display, instead of the
frequency. Most RDS stations provide their station
name, the time of day and a Program Type (PTY)
for their current programming.

3-23
Finding a PTY Station
P
-TYP (Program Type): This button is used to turn
on and off Program Type (PTY) select. The P
-TYPE
symbol will appear on the display and the SELECT
LED indicator next to the P
-TYP button will light.
The last selected PTY will appear on the display for five
seconds. Turn the AUDIO knob to select the PTY you
want to listen to. Press the SEEK arrows to find radio
stations of the PTY you want to listen to. The last
PTY selected will be used for seek. If a station with the
selected PTY is not found, NOT FOUND will appear on
the display. If both P
-TYP and TRAF are on, the radio
will search for stations with traffic announcements and
the selected PTY.
To use the PTY interrupt feature, press and hold this
button until you hear a beep on the PTY you want to
interrupt. An asterisk will appear next to the PTY name,
example (CLASSICAL*). When you are listening to a
CD, the last selected RDS FM station will interrupt play
if that selected PTY format is broadcast.AM FM (Alternate Frequency): Alternate frequency
allows the radio to switch to a stronger station with the
same program type. Press and hold AM FM for two
seconds to turn alternate frequency on. AF ON will appear
on the display. The radio may switch to stronger stations.
Press and hold AM FM again for two seconds to turn
alternate frequency off. AF OFF will appear on the
display. The radio will not switch to other stations. When
you turn the ignition off and then on again, the alternate
frequency feature will automatically be turned on.
Setting PTY Preset Stations
The six numbered pushbuttons let you return to your
favorite Program Types (PTYs). These pushbuttons have
factory PTY presets. You can set up to 12 PTYs (six FM1
and six FM2) by performing the following steps:
1. Press AM FM to select FM1 or FM2.
2. Press P
-TYP to activate program type mode.
3. Turn the AUDIO knob to select a PTY.
4. Press and hold one of the six numbered pushbuttons
until you hear a beep. Whenever you press that
numbered pushbutton, the PTY you set will return.
5. Repeat the steps for each pushbutton.