lock BUICK LESABRE 2002 Repair Manual

3-19 AM-FM Stereo with Compact Disc Player
with Automatic Tone Control and Radio
Data Systems (RDS) (If Equipped)
Playing the Radio
PWR (Power): Push this knob to turn the system on
and off.
VOL (Volume): Turn this knob clockwise to
increase volume. Turn it counterclockwise to
decrease the volume.DISP (Display): Press this button to display the station
being played or to display the clock. The clock can be
displayed with the ignition on or off.
Finding a Station
AM FM: Press this button to switch between AM,
FM1 and FM2. The display shows your selection.
TUNE: Turn this knob clockwise to tune to the
next station. Turn it counterclockwise to tune to the
previous station.
SEEK : Press the right or left arrow to go to the
next or previous station and stay there. The sound will
mute while seeking. The radio will seek to stations with
a strong signal only.
To scan stations, press and hold one of the SEEK arrows
for two seconds until SCAN appears on the display. The
radio will go to a station, play for a few seconds, then go
on to the next station. Press one of the SEEK arrows
again to stop scanning. The sound will mute while
scanning. The radio will seek to stations with a strong
signal only.

3-20
To scan preset stations, press and hold one of the SEEK
arrows for more than four seconds until PSCAN and the
preset number appear on the display. You will hear a double
beep. The radio will go to the first preset station stored on
your pushbuttons, play for a few seconds, then go on to
the next preset station. Preset scan will only scan the six
presets that are in the band selected. Press one of the SEEK
arrows again to stop scanning your preset stations. The
radio will seek to stations with a strong signal only.
Setting Preset Stations
The six numbered pushbuttons let you return to your
favorite stations. You can set up to 18 stations (six AM,
six FM1 and six FM2) by performing the following steps:
1. Turn the radio on.
2. Press AM FM to select AM, FM1 or FM2.
3. Tune in the desired station.
4. Press EQ to select the EQ setting. It will be stored
with the preset station.
5. Press and hold one of the six numbered pushbuttons.
When you hear the radio produce one beep, release
the pushbutton. Whenever you press that numbered
pushbutton, the station you set will return.
6. Repeat the steps for each pushbutton.Setting the Tone (Bass/Treble)
AUDIO: Push and release AUDIO until BASS appears
on the display. Then turn the AUDIO knob clockwise to
increase bass. BASS and a positive number will appear
on the display. Turn the AUDIO knob counterclockwise
to decrease bass. BASS and a negative number will
appear on the display. BASS and a zero will appear on
the display when the bass level is set to the middle
position. Stop turning the knob when you find the bass
level you want or when the maximum or minimum level
is reached.
Push and release AUDIO until MID appears on the
display. Then turn the AUDIO knob clockwise to
increase treble. MID and a positive number will appear on
the display. Turn the AUDIO knob counterclockwise to
decrease treble. MID and a negative number will appear
on the display. MID and a zero will appear on the display
when the treble level is set to the middle position. Stop
turning the knob when you find the treble level you want
or when the maximum or minimum level is reached.

3-21
Push and release AUDIO until TREBLE appears on the
display. Then turn the AUDIO knob clockwise to
increase treble. TREBLE and a positive number will
appear on the display. Turn the AUDIO knob
counterclockwise to decrease treble. TREBLE and a
negative number will appear on the display. TREBLE
and a zero will appear on the display when the treble
level is set to the middle position. Stop turning the knob
when you find the treble level you want or when the
maximum or minimum level is reached. If a station is
weak or noisy, you may want to decrease the treble.
To adjust bass, midrange or treble to the middle
position, select BASS, MID or TREBLE. Then push and
hold AUDIO for more than two seconds until you hear a
beep. BASS and a zero, MID and a zero or TREBLE
and a zero will appear on the display. To adjust both
tone controls and both speaker controls to the middle
position, end out of audio mode by pushing the AUDIO
knob until the display goes blank. Then push and hold
AUDIO for more than two seconds until you hear a
beep. ALL CENTERED will appear on the display.Adjusting the Speakers (Balance/Fade)
AUDIO: To adjust the balance between the right and
left speakers, push and release AUDIO until BAL
appears on the display. Then turn the AUDIO knob
clockwise to move the sound to the right speakers or
counterclockwise to move the sound to the left speakers.
A bar graph with indicators will show how the sound is
balanced between the right and left speakers. Stop
turning the AUDIO knob when you find the speaker
balance you want or when the maximum or minimum
level is reached.
To adjust the fade between the front and rear speakers,
push and release AUDIO until FADE appears on the
display. Then turn the AUDIO knob clockwise to move
the sound to the front speakers or counterclockwise to
move the sound to the rear speakers. A bar graph with
indicators will show how the sound is balanced between
the front and rear speakers. Stop turning the AUDIO
knob when you find the speaker balance you want or
when the maximum or minimum level is reached.

3-26
Compact Disc Errors
CHECK CD: If this message appears on the radio
display, it could be due to one of the following reasons:

The road is too rough. The disc should play when the
road is smoother.

The disc is dirty, scratched, wet or upside down.

The air is very humid. If so, wait about an hour and
try again.
If the CD is not playing correctly, for any other reason,
try a known good CD.
If any error occurs repeatedly or if an error can't be
corrected, contact your dealer. If your radio displays an
error number, write it down and provide it to your dealer
when reporting the problem.AM-FM Stereo with Cassette Tape and
Compact Disc Player with Automatic Tone
Control and Radio Data Systems (RDS)
(If Equipped)
Playing the Radio
PWR (Power): Push this knob to turn the system on
and off.
VOL (Volume): Turn this knob clockwise to increase
volume. Turn it counterclockwise to decrease the volume.

3-27
DISP (Display): Press this button to display the station
being played or to display the clock. The clock can be
displayed with the ignition on or off.
Finding a Station
AM FM: Press this button to switch between AM, FM1
and FM2. The display shows your selection.
TUNE: Turn this knob clockwise to tune to the
next station. Turn it counterclockwise to tune to the
previous station.
SEEK : Press the right or left arrow to go to the
next or previous station and stay there. The sound will
mute while seeking. The radio will seek to stations with
a strong signal only.
To scan stations, press and hold one of the SEEK arrows
for two seconds until SCAN appears on the display. The
radio will go to a station, play for a few seconds, then go
on to the next station. Press one of the SEEK arrows
again to stop scanning. The sound will mute while
scanning. The radio will seek to stations with a strong
signal only.
To scan preset stations, press and hold one of the SEEK
arrows for more than four seconds until PSCAN and the
preset number appear on the display. You will hear a
double beep. The radio will go to the first preset stationstored on your pushbuttons, play for a few seconds, then
go on to the next preset station. Preset scan will only
scan the six presets that are in the band selected. Press
one of the SEEK arrows again to stop scanning your
preset stations. The radio will seek to stations with a
strong signal only.
Setting Preset Stations
The six numbered pushbuttons let you return to
your favorite stations. You can set up to 18 stations
(six AM, six FM1 and six FM2) by performing the
following steps:
1. Turn the radio on.
2. Press AM FM to select AM, FM1 or FM2.
3. Tune in the desired station.
4. Press EQ to select the EQ setting. It will be stored
with the preset station.
5. Press and hold one of the six numbered pushbuttons.
When you hear the radio produce one beep, release
the pushbutton. Whenever you press that numbered
pushbutton, the station you set will return.
6. Repeat the steps for each pushbutton.

3-28
Setting the Tone (Bass/Treble)
AUDIO: Push and release AUDIO until BASS appears
on the display. Then turn the AUDIO knob clockwise to
increase bass. BASS and a positive number will appear
on the display. Turn the AUDIO knob counterclockwise
to decrease bass. BASS and a negative number will
appear on the display. BASS and a zero will appear on
the display when the bass level is set to the middle
position. Stop turning the knob when you find the bass
level you want or when the maximum or minimum level
is reached.
Push and release AUDIO until MID appears on the
display. Then turn the AUDIO knob clockwise to
increase treble. MID and a positive number will appear
on the display. Turn the AUDIO knob counterclockwise
to decrease treble. MID and a negative number will
appear on the display. MID and a zero will appear on the
display when the treble level is set to the middle
position. Stop turning the knob when you find the treble
level you want or when the maximum or minimum level
is reached.Push and release AUDIO until TREBLE appears on
the display. Then turn the AUDIO knob clockwise to
increase treble. TREBLE and a positive number will
appear on the display. Turn the AUDIO knob
counterclockwise to decrease treble. TREBLE and a
negative number will appear on the display. TREBLE
and a zero will appear on the display when the treble
level is set to the middle position. Stop turning the knob
when you find the treble level you want or when the
maximum or minimum level is reached. If a station is
weak or noisy, you may want to decrease the treble.
To adjust bass, midrange or treble to the middle
position, select BASS, MID or TREBLE. Then push and
hold AUDIO for more than two seconds until you hear a
beep. BASS and a zero, MID and a zero or TREBLE
and a zero will appear on the display. To adjust both
tone controls and both speaker controls to the middle
position, end out of audio mode by pushing the AUDIO
knob until the display goes blank. Then push and hold
AUDIO for more than two seconds until you hear a
beep. ALL CENTERED will appear on the display.

3-29
Adjusting the Speakers (Balance/Fade)
AUDIO: To adjust the balance between the right and
left speakers, push and release AUDIO until BAL
appears on the display. Then turn the AUDIO knob
clockwise to move the sound to the right speakers or
counterclockwise to move the sound to the left speakers.
A bar graph with indicators will show how the sound is
balanced between the right and left speakers. Stop
turning the AUDIO knob when you find the speaker
balance you want or when the maximum or minimum
level is reached.
To adjust the fade between the front and rear speakers,
push and release AUDIO until FADE appears on the
display. Then turn the AUDIO knob clockwise to move
the sound to the front speakers or counterclockwise to
move the sound to the rear speakers. A bar graph with
indicators will show how the sound is balanced between
the front and rear speakers. Stop turning the AUDIO
knob when you find the speaker balance you want or
when the maximum or minimum level is reached.
To adjust balance or fade to the middle position, select
BAL or FADE. Then push and hold AUDIO for more
than two seconds until you hear a beep. The indicator
will be centered on the display To adjust both tone
controls and both speaker controls to the middle
position, end out of audio mode by pushing the AUDIOknob until the display goes blank. Then press and hold
AUDIO for more than two seconds until you hear a
beep. ALL CENTERED will appear on the display.
EQ (Equalizer): This feature allows you to choose
preset bass, mid and treble equalization settings
designed for different program types. Press EQ to select
the desired preset equalization setting. Each time you
press EQ, another setting will appear on the display.
Using RDS
Your audio system is equipped with a Radio Data System
(RDS). With RDS, the radio can do the following:

Seek only to stations with the types of programs you
want to listen to,

seek to stations with traffic announcements,

receive announcements concerning local and
national emergencies, and

receive and display messages from radio stations.
RDS features are only available for use on FM stations
which broadcast RDS information. The RDS features of
your radio rely upon receiving specific RDS information
from these stations. These features will only work when
the RDS information is available. In rare cases, a radio
station may broadcast incorrect information that will
cause the radio features to work improperly. If this
happens, contact the radio station.

3-33
CD TAPE: Press this button to play a cassette tape or a
CD when listening to the radio.
(Eject): Press this button to eject a tape.
Cassette Tape Messages
If an error message appears while trying to play
a cassette tape, it could be for one of the
following reasons:

TIGHT TAPE: The tape is tight and the player can't
turn the tape hubs. Remove the tape. Hold the tape
with the open end down and try to turn the right hub
counterclockwise with a pencil. Turn the tape over
and repeat. If the hubs do not turn easily, your tape
may be damaged and should not be used in the
player. Try a new tape to make sure your player is
working properly.

BROKEN TAPE: The tape is broken. Try a
new tape.
CLEAN PLAYER: If this message appears on the
display, the cassette tape player needs to be cleaned. It
will still play tapes, but you should clean it as soon as
possible to prevent damage to the tapes and player. See
ªCare of Your Cassette Tape Playerº in the Index.If any error occurs repeatedly or if an error can't be
corrected, contact your dealer. If your radio displays an
error number, write it down and provide it to your dealer
when reporting the problem.
CD Adapter Kits
It is possible to use a portable CD player adapter kit
with your cassette tape player after activating the bypass
feature on your tape player.
To activate the bypass feature, use the following steps:

Turn the ignition to RUN or ACCESSORY.

Turn the radio off.

Insert the adapter into the cassette slot.

Press and hold the CD TAPE button until READY
is displayed.
This override routine will remain active until the eject
button is pressed.

3-36
You must first load the magazine with discs before
you can play a compact disc. Each of the 12 trays
holds one disc. Slide the button on the top of the
magazine and gently pull out one of the trays. Load the
trays from top to bottom, placing a disc on the tray label
side up. If you load a disc with the label side down, the
disc will not play and an error will occur. Gently push
the tray back into the magazine slot until it locks into
place. Repeat this procedure for loading up to 12 discs
in the magazine.Once you have loaded the discs in the magazine, slide
open the door of the compact disc (CD) changer. Push
the magazine into the changer in the direction of the
arrow marked on top of the magazine.

3-39
Compact Disc Changer Errors
E (Error): If this message and a number appear on the
display, an error has occurred.
If the error occurred while trying to play a CD in the
compact disc player or changer, the following conditions
may have caused the error:

E30: The road is too rough. The disc should play
when the road is smoother.

E30: The disc is dirty, scratched, wet or
upside down.

E30: The air is very humid. If so, wait about an hour
and try again.

E34: The CD changer door is open. Completely
close the door to restore normal operation.

E35: An empty magazine is inserted in the CD
changer. Try the magazine again with a disc loaded
on one of the trays.
If any error occurs repeatedly or if an error cannot be
corrected, contact your dealer. If your radio displays
an error number other than the error codes listed
previously, write it down and provide it to your dealer
when reporting the problem.Personal Choice Radio Controls
(If Equipped)
This feature enables two drivers to store and recall personal
settings for AM and FM presets, last tuned station, volume,
tone and audio source (radio, cassette or CD).
The memory buttons (1 or 2) for this feature are located
on the driver's door panel and correspond to the
numbers (1 or 2) found on the back of each remote
keyless entry transmitter.
To recall audio sources, press the unlock button on the
remote keyless entry transmitter and put the ignition in
RUN. The source last listened to will be recalled for the
identified driver (1 or 2).
To program this feature, do the following:
1. Set all radio preferences. For more information see
ªSetting Preset Stationsº and ªSetting the Toneº
listed for your particular radio.
2. Locate the memory buttons on the driver's door panel.
3. Press one of the memory buttons (1 or 2) until you
hear two beeps. The beeps confirm that your
selection has been saved and can now be recalled.
Follow these steps each time you want to change the
stored settings.