set clock BUICK RANDEZVOUS 2002 Owner's Manual

2-124
To adjust the HUD so you can see it properly:
1. Start your engine and turn the dimmer knob to the
desired HUD image brightness.
The brightness of the HUD image is determined by
the ambient light conditions in the direction your
vehicle is facing and where you have the HUD
dimmer knob set. If you are facing a dark object or a
heavily shaded area, your HUD may anticipate that
you are entering a dark area and may begin to dim.
2. Adjust the driver's seat. If you change your seat
position later, you may have to readjust your HUD.
3. Press the UP or DN buttons until the HUD image is
easy to see and then press the DN button until the
HUD image is as low as possible, but, remains in full
view straight ahead near the front bumper.
The HUD image can only be adjusted up and down,
not side
-to-side.
4. To turn the image off, turn the dimmer knob
counterclockwise to OFF.
If the sun comes out or it becomes cloudy, you may need
to adjust the HUD brightness again using the dimmer
knob. Polarized sunglasses could make the HUD image
harder to see.When you first start the vehicle the display will show
BUICK and the Buick logo for a few seconds. If it is
cold outside, this display may stay on for up to a minute.
Clean the inside of the windshield as needed to remove
any dirt or film that reduces the sharpness or clarity of
the HUD image.
To clean the HUD, spray household glass cleaner on a
soft, clean cloth. Wipe the HUD lens gently, then dry it.
Do not spray cleaner directly on the lens because the
cleaner could leak into the unit.
If the ignition is on and you can't see the HUD image,
check one of the following:

The HUD unit is covered,

the HUD dimmer knob is adjusted correctly,

the HUD image is adjusted to the proper height,

ambient light (in the direction your vehicle is facing)
is low, or

a fuse is blown. See ªFuses and Circuit Breakersº in
the Index.
Keep in mind that your windshield is part of the HUD
system. If you ever have to have your windshield
replaced, be sure to get one that is designed for HUD or
your HUD image may look blurred and out of focus.

3-
3-1
Section 3 Comfort Controls and Audio Systems
In this section, you'll find out how to operate the comfort control and audio systems offered with your vehicle.
Be sure to read about the particular systems supplied with your vehicle.
3
-2 Comfort Controls
3
-2 Dual Manual Comfort Control
3
-5 Dual Automatic ComforTemp
Climate
Control (If Equipped)
3
-9 Rear Window Defogger
3
-10 Ventilation System
3
-11 Audio Systems
3
-11 Setting the Clock
3
-11 AM-FM Stereo with Compact Disc Player
with Automatic Tone Control and Radio
Data Systems (RDS)
3
-19 AM-FM Stereo with Cassette Tape and
Compact Disc Player with Automatic Tone
Control and Radio Data Systems (RDS)
(If Equipped)3
-28 AM-FM Stereo with Six-Disc Compact Disc
Player with Programmable Equalization and
Radio Data System (RDS) (If Equipped)
3
-38 Rear Seat Audio (RSA) (If Equipped)
3
-40 Theft-Deterrent Feature
3
-41 Audio Steering Wheel Controls (If Equipped)
3
-42 Understanding Radio Reception
3
-42 Tips About Your Audio System
3
-43 Care of Your Cassette Tape Player
3
-44 Care of Your Compact Discs
3
-44 Care of Your Compact Disc Player
3
-44 Integrated Windshield Antenna

3-2
Comfort Controls
This section tells you how to make your air system work
for you.
With this system, you can control the heating, cooling
and ventilation in your vehicle. Your vehicle also has
a flow
-through ventilation system described later in
this section.
Dual Manual Comfort Control
Fan Knob
The left knob is used to select the force of air you want.
Turn the knob clockwise to increase fan speed and
counterclockwise to decrease fan speed. The fan must be
turned on for the air conditioning compressor to operate.Temperature Knob
The center knob controls the temperature of the air
coming through the system. Turn the knob clockwise
(toward the red area) for warmer air. Turn the knob
counterclockwise (toward the blue area) for cooler air.
Mode Knob
The right knob is used to select and determine the
direction of the air flowing into the vehicle.
(Upper): This setting directs air through the
instrument panel outlets and the rear console outlets.
(Bi-Level): This setting directs air into your
vehicle in two ways. Cooler air is directed toward your
upper body through the front instrument panel outlets
and the rear console outlets, while warmed air is
directed through the heater ducts at your feet.
(Lower): This setting brings in most of the air
through the floor ducts. It is also used to send air to the
rear of the vehicle. Keep the area under the front seats
free of objects that could obstruct airflow to the rear of
the vehicle.

3-3
(Defog): This setting directs air to the windshield
and through the floor ducts. This mode is particularly
useful during cold or inclement weather because of your
vehicle's larger windshield area.
(Defrost): This setting directs most of the air to the
windshield and side window vents.
Mode Buttons
(Recirculation): Press this button (the light will
glow) to recirculate the air inside of your vehicle and to
limit the amount of outside air and/or odors entering
the vehicle.
Press this button again (the light will go off) to send
outside air into your vehicle. Using this setting while
trying to defrost or defog the windows will help clear
the vents of moisture. When the defog, defrost or lower
setting is selected, the system will automatically go to
outside air mode.
Operating the Heating/Ventilation/Air Conditioning
(HVAC) system in the recirculation mode may cause
fogging of the vehicle's windows when the weather
is cold and damp. To clear the fog, switch the HVAC
system to either the defog or defrost mode and increase
the fan speed. To avoid refogging of the windows,
operate the HVAC system in the outside air mode.Air Conditioning
On very hot days, your vehicle will cool down more
quickly and economically if you open the windows long
enough to let hot, inside air escape. For all settings,
adjust the temperature knob and fan speed as desired.
To get maximum cooling or a quick cool
-down on
very hot days, press the A/C and recirculation buttons
(the lights will glow) and turn the temperature knob
counterclockwise (toward the blue area). Then, adjust
the mode knob to direct the air to the desired location.
This setting should not be used for long periods of time
because the air may become too cold and dry.
Push the A/C button again (the light will go off) to turn
off the air conditioning.
When the air conditioner compressor is on, you may
sometimes notice slight changes in your vehicle's engine
performance and power. This is normal. The system is
designed to help fuel economy while it maintains the
desired cooling level.
The air conditioner removes moisture from the air, so
you may sometimes notice water dripping from under
your vehicle's engine compartment when it is idling or
after it has been turned off. This is normal.

3-4
Heating
Turn the temperature knob clockwise (toward the red
area) to warm the air.
In the lower mode, outside air will be brought in and
sent through the floor outlets. The heater works best if
you keep your windows closed while using it.
The bi
-level setting is designed for use on sunny days
when the air is only moderately warm or cool. On days
like these, the sun may adequately warm your upper
body, but your lower body may not be warm enough.
For the best results, move the temperature knob to the
middle position, and then adjust it for comfort.
Your vehicle has a computer controlled transaxle
designed to warm up the engine faster when the outside
temperature is 35
F (2
C) or colder. You may notice
that the transaxle will shift at a higher vehicle speed
until the engine is warmed up. This is a normal
condition designed to provide heat to the passenger
compartment and defrost the windows more quickly.
If your vehicle is equipped with an engine coolant heater
and you use it during cold weather, 0
F (
-18
C) or
lower, your heating system will provide heat more
quickly because the engine coolant is already warmed.
See ªEngine Coolant Heaterº in the Index.Defogging and Defrosting
Your system has two settings for clearing the front and
side windows.
To rapidly defrost the windshield, turn the temperature
knob all the way clockwise (to the red area) and turn the
mode knob to defrost. Adjust the fan to the highest speed.
To keep the windshield clear and bring in heated air
through the heater ducts, turn the mode knob to defog.
When the temperature outside is above freezing, the air
conditioner compressor will run in these settings to help
remove moisture from the air.
Your vehicle is equipped with side window defogger
vents located on the top of the instrument panel. For
additional side window defogging, turn the mode knob
to the bi
-level setting and adjust the fan to the highest
speed. Aim the side vents on the instrument panel
toward the side windows. For increased airflow to the
side vents, close the center vents.
Operating the HVAC system in the recirculation mode may
cause fogging of the vehicle's windows when the weather is
cold and damp. To clear the fog, switch the HVAC system to
either the defog or defrost mode and increase the fan speed.
To avoid re
-fogging of the windows, operate the HVAC
system in the outside air mode.
For additional information, refer to ªRecirculationº
earlier in this section.

3-5 Dual Automatic ComforTemp Climate
Control (If Equipped)
With this system, you set a temperature. You can then
either let the system automatically control airflow
direction and force to maintain the temperature, or you
can manually adjust it. The system works best if you
keep your windows closed while using it.
The vehicle's interior will warm up or cool down at the
same rate no matter which temperature you choose. For
example, if you set the system at 90
F (32
C) it will not
heat any faster than if you had set it at 70
F (21
C).
It will just continue to heat longer.Automatic Control
For the most efficient operation, you should set the
system temperature and push the driver's temperature
knob for automatic operation. The word AUTO will be
shown in the display. The system will select the best fan
speed and airflow settings to keep you comfortable.
The air conditioning compressor will run if the outside
temperature is above 32
F (0
C). You may notice a
delay of two to three minutes before the fan comes on
when you start your vehicle in cool weather.
Driver's Temperature Control
The driver's temperature knob sets the temperature for
the system when the passenger's temperature setting is
in neutral. If the passenger's temperature setting is not in
neutral, the driver's temperature knob sets the
temperature for the driver only.
Turn the knob clockwise to raise the temperature and
counterclockwise to lower the temperature. The display
will show the temperature briefly, then the outside
temperature will be displayed.
If you push the temperature knob for automatic
operation, the system will control the fan speed and
air temperature.

3-6
Passenger's Temperature Control
The passenger's temperature knob adjusts the
temperature on the passenger's side of the vehicle so
it is warmer or cooler than the temperature set by the
driver. The passenger temperature setting is shown
under the words PASS TEMP in the display.
Turn the knob clockwise to raise the temperature and
counterclockwise to lower the temperature. The display
will not show the passenger's temperature
-- only that
of the driver. Indicators under the words PASS TEMP in
the display will show passenger temperature relative
driver's set temperature.
The large single bar in the center of the + and
- symbols
(neutral) indicates the same temperature as the driver.
The bars between the center bar and the + symbol
indicate a warmer temperature setting than the driver.
The bars between the center bar and the
- symbol
indicate a cooler temperature setting than the driver.
Manual Control
You can also manually control the heating, cooling
and ventilation in your vehicle. You can select airflow
direction, fan speed, outside or recirculated air and air
compressor operation by using the following:Mode Button
This button has several settings to control direction of
airflow when the system is not in AUTO. To access the
various modes available, continue to press MODE until
the desired mode appears in the display.
(Defog): This setting directs half of the air to
the floor ducts and half to the defroster and side
window vents.
(Bi-Level): This setting directs half of the air
through the instrument panel outlets. Most of the
remaining air is directed through the floor ducts and
a little to the defroster and side window vents.
(Upper): This setting directs air through the
instrument panel outlets.
(Lower): This setting brings in most of the air
through the floor ducts. The rest comes out of the
defroster and side window vents.
(Defrost): This setting brings in outside air and
directs most of the air through the defrost vent. Some of
the air also goes to the floor ducts and the side window
defogger outlets. The air conditioning compressor will
run automatically in this setting unless the outside
temperature is below 32
F (0
C).

3-11
Audio Systems
Your audio system has been designed to operate easily
and give years of listening pleasure. You will get the most
enjoyment out of it if you acquaint yourself with it first.
Find out what your audio system can do and how to
operate all of it's controls, to be sure you're getting the
most out of the advanced engineering that went into it.
Your vehicle has a feature called Retained Accessory
Power (RAP). With RAP, you can play your audio
system even after the ignition is turned off. See
ªRetained Accessory Powerº in the Index.
Setting the Clock
Press and hold H until the correct hour appears. AM will
appear on the display for morning hours. Press and hold
M until the correct minute appears. The clock may be
set with the ignition on or off.
To set the clock to the time of an FM station
broadcasting Radio Data System (RDS) information.
Press and hold H and M at the same time until TIME
UPDATED appears on the display. If the time is not
available from the station, NO UPDATE will appear on
the display.
AM-FM Stereo with Compact Disc Player
with Automatic Tone Control and Radio
Data Systems (RDS)
Playing the Radio
PWR (Power): Push this knob to turn the system on
and off.
VOL (Volume): Turn this knob clockwise to
increase volume. Turn it counterclockwise to decrease
the volume.

3-12
DISP (Display): Press this button to display the station
being played or to display the clock. The clock can be
displayed with the ignition on or off.
Finding a Station
AM FM: Press this button to switch between AM, FM1
and FM2. The display shows your selection.
TUNE: Turn this knob clockwise to tune in to the next
station. Turn it counterclockwise to tune into the
previous station.
SEEK : Press the right or left arrow to go to the
next or previous station and stay there. The sound will
mute while seeking. The radio will seek to stations with
a strong signal only.
To scan stations, press one of the SEEK arrows for two
seconds and SCAN will appear on the display. The radio
will go to a station, play for a few seconds, then go on
to the next station. Press one of the SEEK arrows again
to stop scanning. The sound will mute while scanning.
The radio will seek to stations with a strong signal only.
To scan preset stations, press one of the SEEK arrows
for four seconds and PSCAN will appear on the display.The radio will go to a station, play for a few seconds,
then go on to the next station. Press one of the SEEK
arrows again to stop scanning your preset stations.
The sound will mute while scanning. The radio will
seek to stations with a strong signal only.
Setting Preset Stations
The six numbered pushbuttons let you return to your
favorite stations. You can set up to 18 stations
(six AM, six FM1 and six FM2) by performing the
following steps:
1. Turn the radio on.
2. Press AM FM to select the band.
3. Tune in the desired station.
4. Press EQ to select the equalization. It will be stored
with the preset station.
5. Press and hold one of the six numbered pushbuttons.
When you hear the radio produce one beep, release
the pushbutton. Whenever you press that numbered
pushbutton, the station you set will return.
6. Repeat the steps for each pushbutton.

3-13
Setting the Tone (Bass/Treble)
AUDIO: Push and release AUDIO until BASS appears
on the display. Then turn the AUDIO knob clockwise to
increase bass. BASS and a positive number will appear
on the display. Turn the AUDIO knob counterclockwise
to decrease bass. BASS and a negative number will
appear on the display. BASS and a zero will appear on
the display when the bass level is set to the middle
position. Stop turning the knob when you find the bass
level you want or when the maximum or minimum level
is reached.
Push and release AUDIO until MID appears on the
display. Then turn the AUDIO knob clockwise to
increase treble. MID and a positive number will appear
on the display. Turn the AUDIO knob counterclockwise
to decrease treble. MID and a negative number will
appear on the display. MID and a zero will appear on the
display when the treble level is set to the middle
position. Stop turning the knob when you find the treble
level you want or when the maximum or minimum level
is reached.Push and release AUDIO until TREBLE appears on the
display. Then turn the AUDIO knob clockwise to
increase treble. TREBLE and a positive number will
appear on the display. Turn the AUDIO knob
counterclockwise to decrease treble. TREBLE and a
negative number will appear on the display. TREBLE
and a zero will appear on the display when the treble
level is set to the middle position. Stop turning the knob
when you find the treble level you want or when the
maximum or minimum level is reached. If a station is
weak or noisy, you may want to decrease the treble.
To adjust bass, midrange or treble to the middle
position, select BASS, MID or TREBLE. Then push and
hold AUDIO for more than two seconds until you hear a
beep. BASS and a zero, MID and a zero or TREBLE
and a zero will appear on the display. To adjust both
tone controls and both speaker controls to the middle
position, end out of audio mode, by pushing the AUDIO
knob until the display goes blank. Then push and hold
AUDIO for more than two seconds until you hear a
beep. ALL CENTERED will appear on the display.