BUICK RANDEZVOUS 2002 Owner's Manual

2-13
Replacing the Battery in the Remote Transmitter
NOTICE:
When replacing the battery, use care not to
touch any of the circuitry. Static from your
body transferred to these surfaces may damage
the transmitter.
1. Insert a flat object, such as a coin, into the slot on the
side of the transmitter and twist to separate the halves.
2. Gently pry the battery out of the transmitter. Do not
use the metal flanges to ªpop outº the battery.
3. Replace the battery.
4. Reassemble the transmitter. Make sure the halves are
snapped together tightly so water will not get in.
5. Check the transmitter operation.
Center Console Switchbank
There is a center console switchbank located in the
instrument panel, below the comfort controls.
The switches will vary with the options that are
on your vehicle.
The center console switchbank consists of five switches.
The five possible switches are for the rear window
wiper/washer, the liftgate release, the traction disable,
the park aid disable, and the driver's and passenger's
heated seats. If your vehicle does not have some of the
options controlled by these switches, there will be a
blank button in its place.
For more information, see each of these features in
the Index.

2-14
Vehicle Customization
Some of your vehicle's features can be reset or
customized according to your preference. The features
you can program depend on the options that came with
your vehicle.
If your vehicle is equipped with the DIC, see ªDriver
Information Centerº in the Index to customize
your features.
The following features can be customized according to
the options that your vehicle has, if you do not have
the DIC.
Entering Programming Mode
To program features, your vehicle must be in the
programming mode. Follow these steps:
1. Turn the ignition key to ON. The gearshift must be
in PARK (P).
2. Press and hold the trip/reset button, located next to
the odometer for two seconds while the odometer is
in the odometer mode.
United States Canada

2-15
3. This message will appear in the message center,
located in the instrument panel cluster, as an
indication that your vehicle is ready to
begin programming.
If you have the optional remote keyless entry system,
you must press the LOCK button. This lets the
system know which transmitter is being
personalized. Each remote keyless entry transmitter
can be personalized differently.
You can now program your choices.
To exit the programming mode, follow the steps
listed under ªExiting Programming Modeº later
in this section.Headlamp Exit Delay
This feature allows you to customize the headlamps and
parking lamps.
Programmable Modes
Mode 1: Off (The headlamps and parking lamps
will turn off at the same time that the ignition is turned
to OFF.)
Mode 2: 15
-Second Activation (The headlamps and
parking lamps will stay on for 15 seconds when the
ignition is turned to OFF.)
Mode 3: 30
-Second Activation (The headlamps and
parking lamps will stay on for 30 seconds when the
ignition is turned to OFF.)
Mode 4: 60
-Second Activation (The headlamps and
parking lamps will stay on for 60 seconds when the
ignition is turned to OFF.)

2-16
Before your vehicle was shipped from the factory, it was
programmed in Mode 3. The mode to which the vehicle
has been programmed may have been changed since it
left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Turn the exterior lamp control from the off position
to the parking lamp position.
3. Count the number of chimes you hear. The number of
chimes indicates the vehicle's current programmed
mode. If you do not wish to change the current mode,
you can either exit the programming mode by
following the instructions later in this section or
program the next feature available on your vehicle.
4. Turn the exterior lamp control from the off position to
the parking lamp position to change the current mode.
5. Turn the exterior lamp control from the off position
to the parking lamp position until you hear the
number of chimes corresponding to the mode
selection you want.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.Automatic Door Lock/Unlock
This feature allows you to lock and unlock your
doors automatically.
Programmable Modes
Mode 1: Both Features Off (Automatic door locking
and unlocking is disabled. You will always need to
lock your doors manually before driving to increase
occupant safety.)
Mode 2: Automatic Door Locking Only

Shift out of PARK (P) with the ignition on and the
driver's door closed; all doors will lock automatically.

The automatic door unlock feature is turned off.
Mode 3: Automatic Door Locking with shift out
of PARK (P)/Driver's Door Unlocking with shift
into PARK (P)

Shift out of PARK (P) with the ignition on and the
driver's door closed; all doors will lock automatically.

Shift into PARK (P) with the ignition on; driver's
door only will unlock automatically.

2-17
Mode 4: Automatic Door Locking with shift out of
PARK (P)/All Door Unlocking with shift into PARK (P)

Shift out of PARK (P) with the ignition on and the
driver's door closed; all doors will lock automatically.

Shift into PARK (P) with the ignition on; all doors
will unlock automatically.
Mode 5: Automatic Door Locking with shift out of
PARK (P)/Driver's Door Unlocking with Key Removal

Shift out of PARK (P) with the ignition on and the
driver's door closed; all doors will lock automatically.

Remove the key; only the driver's door will
unlock automatically.
Mode 6: Automatic Door Locking with shift out of
PARK (P)/All Door Unlocking with Key Removal

Shift out of PARK (P) with the ignition on and the
driver's door closed; all doors will lock automatically.

Remove the ignition key; all doors will
unlock automatically.Before your vehicle was shipped from the factory, it was
programmed in Mode 4. The mode to which the vehicle
has been programmed may have been changed since it
left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the front of the power door lock switch.
3. Count the number of chimes you hear. The number
of chimes indicates the vehicle's current programmed
mode. If you do not wish to change the current mode,
you can either exit the programming mode by
following the instructions later in this section or
program the next feature available on your vehicle.
4. Press the front of the power door lock switch to
change the current mode.
5. Press the front of the power door lock switch until
you hear the number of chimes corresponding to the
mode selection you want.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-18
Delayed Locking
This feature allows you to delay the locking of
your doors.
Programmable Modes
Mode 1: Off (Doors will always lock immediately when
you lock the doors using the power door lock switch or
the optional remote keyless entry transmitter.)
Mode 2: Delayed Locking (If the power door lock
switch or the optional remote keyless entry transmitter is
used to lock the vehicle while any door is open, you will
hear three chimes. The doors will not lock. Five seconds
after the last door is closed, all doors will lock.)
Before your vehicle was shipped from the factory, it was
programmed in Mode 2. The mode to which the vehicle
has been programmed may have been changed since it
left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the back of the power door lock switch.
3. Count the number of chimes you hear. The
number of chimes indicates the vehicle's current
programmed mode. If you do not wish to change
the current mode, you can either exit the
programming mode by following the instructions
later in this section or program the next feature
available on your vehicle.
4. Press the back of the power door lock switch to
change the current mode.
5. Press the back of the power door lock switch until
you hear the number of chimes corresponding to the
mode selection you want.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-19 Remote Driver's Door Unlock
This feature allows you to customize the UNLOCK
button on the remote keyless entry transmitter.
Programmable Modes
Your vehicle can be programmed to one of the
following modes.
Mode 1: Remote All Doors Unlock (When you press
UNLOCK on your remote keyless entry transmitter, all
doors will unlock.)
Mode 2: Remote Driver's Door Unlock Only
(When you press UNLOCK on your remote keyless
entry transmitter once, the driver's door will unlock.
When you press UNLOCK on your remote keyless
entry transmitter again within five seconds, all doors
will unlock.)
Before your vehicle was shipped from the factory, it was
programmed in Mode 2. The mode to which the vehicle
has been programmed may have been changed since it
left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.2. Press UNLOCK on the remote keyless
entry transmitter.
3. Count the number of chimes you hear. The number of
chimes indicates the vehicle's current programmed
mode. If you do not wish to change the current mode,
you can either exit the programming mode by
following the instructions later in this section or
program the next feature available on your vehicle.
4. Press UNLOCK on the remote keyless entry
transmitter to change the current mode.
5. Press UNLOCK on the remote keyless entry
transmitter until you hear the number of chimes
corresponding to the mode selection you want.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
Remote Lock and Unlock Confirmation
This feature allows you to customize the feedback
received when locking or unlocking your vehicle with
the remote keyless entry transmitter.

2-20
Programmable Modes
Mode 1: Both Features Off (Remote lock and unlock
confirmation are disabled.)
Mode 2: Exterior Lamps Flash Only

When you use the remote keyless entry transmitter to
lock your vehicle, your headlamps and parking
lamps will flash briefly to let you know the
command has been received.

When you use the remote keyless entry transmitter to
unlock your vehicle, your headlamps and parking
lamps will flash briefly to let you know the
command has been received.
Mode 3: Exterior Lamps Flash and Horn Sound

When you use the remote keyless entry transmitter to
lock your vehicle, your headlamps and parking
lamps will flash briefly on each press and your horn
will sound briefly on the second or any other press to
let you know the command has been received.

When you use the remote keyless entry transmitter to
unlock your vehicle, your headlamps and parking
lamps will flash briefly to let you know the
command has been received.Before your vehicle was shipped from the factory, it was
programmed in Mode 3. The mode to which the vehicle
has been programmed may have been changed since it
left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the LOCK button on the remote keyless
entry transmitter.
3. Count the number of chimes you hear. The number of
chimes indicates the vehicle's current programmed
mode. If you do not wish to change the current mode,
you can either exit the programming mode by
following the instructions later in this section or
program the next feature available on your vehicle.
4. Press LOCK on the remote keyless entry transmitter
to change the current mode.
5. Press LOCK on the remote keyless entry transmitter
until you hear the number of chimes corresponding
to the mode selection you want.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-21 Exiting Programming Mode
To exit programming mode, do one of the following:

Press the odometer button, while in odometer mode,
for two seconds, or

turn the ignition key out of ON, or

do not program any commands for one minute while
in programming mode, or

shift out of PARK (P). See ªShifting Out of
PARK (P)º in the Index.
The programming mode message will turn off to let you
know that you are no longer in the programming mode.
Liftgate
CAUTION:
It can be dangerous to drive with the liftgate
open because carbon monoxide (CO) gas can
come into your vehicle. You can't see or smell
CO. It can cause unconsciousness and even death.
If you must drive with the liftgate open or if
electrical wiring or other cable connections
must pass through the seal between the body and
the liftgate:

Make sure all other windows are shut.

Turn the fan on your heating or cooling
system to its highest speed with the setting
on bi
-level (outside air button is pressed).
That will force outside air into your vehicle.
See ªComfort Controlsº in the Index.

If you have air outlets on or under the
instrument panel, open them all the way.
See ªEngine Exhaustº in the Index.

2-22
Liftgate Release
To open the liftgate do one of the following:

press the liftgate release
switch, which is located
on the center console
switchbank, or

press REAR on the optional remote keyless
entry transmitter.
Your vehicle must be in PARK (P) or NEUTRAL (N)
for the liftgate to release.
The liftgate will lock when closed. You will have to use
one of the previous options to open the liftgate again.
Theft
Vehicle theft is big business, especially in some cities.
Although your vehicle has a number of theft
-deterrent
features, we know that nothing we put on it can make
it impossible to steal. However, there are ways you
can help.
Key in the Ignition
If you leave your vehicle with the keys inside, it's an
easy target for joy riders or professional thieves
-- so
don't do it.
When you park your vehicle and open the driver's door,
you'll hear a chime reminding you to remove your key
from the ignition and take it with you. Always do this.
Your steering wheel will be locked, and so will your
ignition and transaxle. Also remember to lock the doors.