heating BUICK RANDEZVOUS 2002 Owner's Manual

2-21 Exiting Programming Mode
To exit programming mode, do one of the following:

Press the odometer button, while in odometer mode,
for two seconds, or

turn the ignition key out of ON, or

do not program any commands for one minute while
in programming mode, or

shift out of PARK (P). See ªShifting Out of
PARK (P)º in the Index.
The programming mode message will turn off to let you
know that you are no longer in the programming mode.
Liftgate
CAUTION:
It can be dangerous to drive with the liftgate
open because carbon monoxide (CO) gas can
come into your vehicle. You can't see or smell
CO. It can cause unconsciousness and even death.
If you must drive with the liftgate open or if
electrical wiring or other cable connections
must pass through the seal between the body and
the liftgate:

Make sure all other windows are shut.

Turn the fan on your heating or cooling
system to its highest speed with the setting
on bi
-level (outside air button is pressed).
That will force outside air into your vehicle.
See ªComfort Controlsº in the Index.

If you have air outlets on or under the
instrument panel, open them all the way.
See ªEngine Exhaustº in the Index.

2-69
Ashtray and Cigarette Lighter
The ashtray is located on the floor console closest to the
instrument panel. Lift the lid to expose the ashtray. The
ashtray removes by lifting it up.
The cigarette lighter is located on the floor console in
the cell phone storage compartment closest to the
driver's seat. Lift the lid to expose the cigarette lighter.
To use the lighter, push it in all the way and let go.
When it's ready, it will pop back out by itself.
NOTICE:
Don't hold a cigarette lighter in with your hand
while it is heating. If you do, it won't be able to
back away from the heating element when it's
ready. That can make it overheat, damaging the
lighter and the heating element.
NOTICE:
Don't put papers and other things that burn
into your ashtrays. If you do, cigarettes or
other smoking materials could set them on fire,
causing damage.
Sun Visors
To block out glare you can swing down the visors.
You can also remove them from the center mount and
swing them to the side. There is an extension on the
inboard side of the sun visors. Pull the extension out to
block out glare.
Lighted Visor Vanity Mirrors
Pull down the sun visor. Flip up the cover to expose the
vanity mirror. The lamps will come on when you open
the cover.

2-89
If the traction control system warning light comes on
and stays on for an extended period of time when the
system is turned on, your vehicle needs service.
Engine Coolant Temperature Gage
United States Canada
This gage shows the engine coolant temperature. If the
gage pointer moves into the red area, your engine is
too hot!It means that your engine coolant has overheated. If you
have been operating your vehicle under normal driving
conditions, you should pull off the road, stop as soon
your vehicle and turn off the engine as soon as possible.
See ªEngine Overheatingº in the Index.

2-96
Traction Active Message (Option)
United States Canada
If your vehicle has the traction control system, the
TRACTION ACTIVE message will appear when the
traction control system is limiting wheel spin. You may
feel or hear the system working, but this is normal.
Slippery road conditions may exist if this message
appears, so adjust your driving accordingly. The
message will stay on for a few seconds after the traction
control system stops limiting wheel spin.
Engine Coolant Temperature
Warning Message
United States Canada
This message will come on when your engine gets
too hot.
If this message comes on, it means that your engine
coolant has overheated. If you have been operating your
vehicle under normal driving conditions, you should
pull off the road, stop your vehicle and turn off the
engine as soon as possible.
See ªEngine Overheatingº in the Index.

3-2
Comfort Controls
This section tells you how to make your air system work
for you.
With this system, you can control the heating, cooling
and ventilation in your vehicle. Your vehicle also has
a flow
-through ventilation system described later in
this section.
Dual Manual Comfort Control
Fan Knob
The left knob is used to select the force of air you want.
Turn the knob clockwise to increase fan speed and
counterclockwise to decrease fan speed. The fan must be
turned on for the air conditioning compressor to operate.Temperature Knob
The center knob controls the temperature of the air
coming through the system. Turn the knob clockwise
(toward the red area) for warmer air. Turn the knob
counterclockwise (toward the blue area) for cooler air.
Mode Knob
The right knob is used to select and determine the
direction of the air flowing into the vehicle.
(Upper): This setting directs air through the
instrument panel outlets and the rear console outlets.
(Bi-Level): This setting directs air into your
vehicle in two ways. Cooler air is directed toward your
upper body through the front instrument panel outlets
and the rear console outlets, while warmed air is
directed through the heater ducts at your feet.
(Lower): This setting brings in most of the air
through the floor ducts. It is also used to send air to the
rear of the vehicle. Keep the area under the front seats
free of objects that could obstruct airflow to the rear of
the vehicle.

3-3
(Defog): This setting directs air to the windshield
and through the floor ducts. This mode is particularly
useful during cold or inclement weather because of your
vehicle's larger windshield area.
(Defrost): This setting directs most of the air to the
windshield and side window vents.
Mode Buttons
(Recirculation): Press this button (the light will
glow) to recirculate the air inside of your vehicle and to
limit the amount of outside air and/or odors entering
the vehicle.
Press this button again (the light will go off) to send
outside air into your vehicle. Using this setting while
trying to defrost or defog the windows will help clear
the vents of moisture. When the defog, defrost or lower
setting is selected, the system will automatically go to
outside air mode.
Operating the Heating/Ventilation/Air Conditioning
(HVAC) system in the recirculation mode may cause
fogging of the vehicle's windows when the weather
is cold and damp. To clear the fog, switch the HVAC
system to either the defog or defrost mode and increase
the fan speed. To avoid refogging of the windows,
operate the HVAC system in the outside air mode.Air Conditioning
On very hot days, your vehicle will cool down more
quickly and economically if you open the windows long
enough to let hot, inside air escape. For all settings,
adjust the temperature knob and fan speed as desired.
To get maximum cooling or a quick cool
-down on
very hot days, press the A/C and recirculation buttons
(the lights will glow) and turn the temperature knob
counterclockwise (toward the blue area). Then, adjust
the mode knob to direct the air to the desired location.
This setting should not be used for long periods of time
because the air may become too cold and dry.
Push the A/C button again (the light will go off) to turn
off the air conditioning.
When the air conditioner compressor is on, you may
sometimes notice slight changes in your vehicle's engine
performance and power. This is normal. The system is
designed to help fuel economy while it maintains the
desired cooling level.
The air conditioner removes moisture from the air, so
you may sometimes notice water dripping from under
your vehicle's engine compartment when it is idling or
after it has been turned off. This is normal.

3-4
Heating
Turn the temperature knob clockwise (toward the red
area) to warm the air.
In the lower mode, outside air will be brought in and
sent through the floor outlets. The heater works best if
you keep your windows closed while using it.
The bi
-level setting is designed for use on sunny days
when the air is only moderately warm or cool. On days
like these, the sun may adequately warm your upper
body, but your lower body may not be warm enough.
For the best results, move the temperature knob to the
middle position, and then adjust it for comfort.
Your vehicle has a computer controlled transaxle
designed to warm up the engine faster when the outside
temperature is 35
F (2
C) or colder. You may notice
that the transaxle will shift at a higher vehicle speed
until the engine is warmed up. This is a normal
condition designed to provide heat to the passenger
compartment and defrost the windows more quickly.
If your vehicle is equipped with an engine coolant heater
and you use it during cold weather, 0
F (
-18
C) or
lower, your heating system will provide heat more
quickly because the engine coolant is already warmed.
See ªEngine Coolant Heaterº in the Index.Defogging and Defrosting
Your system has two settings for clearing the front and
side windows.
To rapidly defrost the windshield, turn the temperature
knob all the way clockwise (to the red area) and turn the
mode knob to defrost. Adjust the fan to the highest speed.
To keep the windshield clear and bring in heated air
through the heater ducts, turn the mode knob to defog.
When the temperature outside is above freezing, the air
conditioner compressor will run in these settings to help
remove moisture from the air.
Your vehicle is equipped with side window defogger
vents located on the top of the instrument panel. For
additional side window defogging, turn the mode knob
to the bi
-level setting and adjust the fan to the highest
speed. Aim the side vents on the instrument panel
toward the side windows. For increased airflow to the
side vents, close the center vents.
Operating the HVAC system in the recirculation mode may
cause fogging of the vehicle's windows when the weather is
cold and damp. To clear the fog, switch the HVAC system to
either the defog or defrost mode and increase the fan speed.
To avoid re
-fogging of the windows, operate the HVAC
system in the outside air mode.
For additional information, refer to ªRecirculationº
earlier in this section.

3-6
Passenger's Temperature Control
The passenger's temperature knob adjusts the
temperature on the passenger's side of the vehicle so
it is warmer or cooler than the temperature set by the
driver. The passenger temperature setting is shown
under the words PASS TEMP in the display.
Turn the knob clockwise to raise the temperature and
counterclockwise to lower the temperature. The display
will not show the passenger's temperature
-- only that
of the driver. Indicators under the words PASS TEMP in
the display will show passenger temperature relative
driver's set temperature.
The large single bar in the center of the + and
- symbols
(neutral) indicates the same temperature as the driver.
The bars between the center bar and the + symbol
indicate a warmer temperature setting than the driver.
The bars between the center bar and the
- symbol
indicate a cooler temperature setting than the driver.
Manual Control
You can also manually control the heating, cooling
and ventilation in your vehicle. You can select airflow
direction, fan speed, outside or recirculated air and air
compressor operation by using the following:Mode Button
This button has several settings to control direction of
airflow when the system is not in AUTO. To access the
various modes available, continue to press MODE until
the desired mode appears in the display.
(Defog): This setting directs half of the air to
the floor ducts and half to the defroster and side
window vents.
(Bi-Level): This setting directs half of the air
through the instrument panel outlets. Most of the
remaining air is directed through the floor ducts and
a little to the defroster and side window vents.
(Upper): This setting directs air through the
instrument panel outlets.
(Lower): This setting brings in most of the air
through the floor ducts. The rest comes out of the
defroster and side window vents.
(Defrost): This setting brings in outside air and
directs most of the air through the defrost vent. Some of
the air also goes to the floor ducts and the side window
defogger outlets. The air conditioning compressor will
run automatically in this setting unless the outside
temperature is below 32
F (0
C).

3-7
Mode Buttons
VENT: This button turns the air conditioning
compressor on and off and changes the mode to
upper. The words A/C OFF are shown in the display.
Recirculation is not permitted when the compressor
is off. The system will try to control the temperature
automatically, but without the compressor.
(Recirculation): Press this button
(the recirculation symbol in the display will be lit) to
recirculate the air inside of your vehicle and to limit the
amount of outside air and/or odors entering the vehicle.
Press this button again (the recirculation symbol will
go off) to send outside air into your vehicle. Using this
setting while trying to defrost or defog the windows will
help clear the vents of moisture. When the defog, defrost
or lower setting is selected, the system will
automatically go to outside air mode.
Operating the Heating/Ventilation/Air Conditioning
(HVAC) system in the recirculation mode may cause
fogging of the vehicle's windows when the weather
is cold and damp. To clear the fog, switch the HVAC
system to either the defog or defrost mode and increase
the fan speed. To avoid refogging of the windows,
operate the HVAC system in the outside air mode.Air Conditioning
On very hot days, your vehicle will cool down more
quickly and economically if you open the windows long
enough to let hot, inside air escape. For all settings,
adjust the temperature knob and fan speed as desired.
To get maximum cooling or a quick cool
-down on very
hot days, press the recirculation button (the recirculation
symbol in the display will be lit) and turn the
temperature knob to the desired interior temperature.
Then, select the mode to direct the air to the desired
location. This setting should not be used for long
periods of time because the air may become too cold
and dry.
Push the recirculation button again (the recirculation
symbol will go off) to turn off recirculation.
When the air conditioner compressor is on, you may
sometimes notice slight changes in your vehicle's engine
performance and power. This is normal. The system is
designed to help fuel economy while it maintains the
desired cooling level.
The air conditioner removes moisture from the air, so
you may sometimes notice water dripping from under
your vehicle's engine compartment when it is idling or
after it has been turned off. This is normal.

3-8
Heating
Turn the temperature knob to the desired interior
temperature to warm the air.
In the lower mode, outside air will be brought in and
sent through the floor outlets. The heater works best if
you keep your windows closed while using it.
The bi
-level setting is designed for use on sunny days
when the air is only moderately warm or cool. On days
like these, the sun may adequately warm your upper
body, but your lower body may not be warm enough.
For the best results, move the temperature knob to the
middle position, and then adjust it for comfort.
Your vehicle has a computer controlled transaxle
designed to warm up the engine faster when the outside
temperature is 35
F (2
C) or colder. You may notice
that the transaxle will shift at a higher vehicle speed
until the engine is warmed up. This is a normal
condition designed to provide heat to the passenger
compartment and defrost the windows more quickly.If your vehicle is equipped with an engine coolant heater
and you use it during cold weather, 0
F (
-18
C) or
lower, your heating system will provide heat more
quickly because the engine coolant is already warmed.
See ªEngine Coolant Heaterº in the Index.
Defogging and Defrosting
Your system has two settings for clearing the front and
side windows.
To defrost the windows quickly, press the defrost button
and set the temperature to 90
F (32
C) and select a high
fan speed.
To warm passengers while keeping the window clear,
select the defog mode with the mode button (the defog
symbol will be lit). Select the fan speed for comfort and
windshield clearing performance.