start stop button BUICK RANDEZVOUS 2002 Owner's Manual

2-88
Anti-Lock Brake System Warning Light
United States Canada
The anti
-lock brake system warning light should come
on for a few seconds when you turn the ignition key to
ON. If the anti
-lock brake system warning light stays on
longer than normal after you've started your engine, turn
the ignition off. Or, if the light comes on and stays on
when you're driving, stop as soon as possible and turn
the ignition off. Then start the engine again to reset the
system. If the light still stays on, or comes on again
while you're driving, the anti
-lock brake system needs
service and you don't have anti
-lock brakes.
The anti
-lock brake system warning light should come
on briefly when you turn the ignition key to ON. If the
light doesn't come on then, have it fixed so it will be
ready to warn you if there is a problem.
Traction Control System Warning Light
(If Equipped)
United States Canada
The traction control system warning light may come on
for the following reasons:

If you turn the system off by pressing the TRAC
OFF button located in the center console switchbank
the warning light will come on and stay on. To turn
the system back on, press the button again. The
warning light should go off. See ªTraction Control
Systemº in the Index for more information.

If there's an engine
-related and brake system problem
that is specifically related to traction control, the
traction control system will turn off and the warning
light will come on. If the brake system problem is
caused by the brakes beginning to overheat, the
brakes will need to cool down before the traction
control system warning light will turn off.

3-17
TRAF (Traffic): Press this button to receive traffic
announcements. The traffic announcement brackets will
appear on the display. TRAF will appear on the display
if the tuned station broadcasts traffic announcements.
If the current tuned station does not broadcast traffic
announcements, the radio will seek to a station that
does. When the radio finds a station that broadcasts
traffic announcements, it will stop. If no station is
found, NO TRAFFIC will appear on the display.
When a traffic announcement comes on the current radio
station or a related network station, you will hear it,
even if the volume is muted or a CD is playing. If the
CD player was being used, the CD will stay in the player
and resume play at the point where it stopped.Radio Messages
CAL (CALIBRATE): Your audio system has been
calibrated for your vehicle from the factory. If this
message appears on the display it means that your radio
has not been configured properly for your vehicle and
must be returned to the dealership for service.
Playing a Compact Disc
Insert a disc partway into the slot, label side up. The
player will pull it in. The disc should begin playing.
If you want to insert a CD while the ignition or the
radio is off, first press the eject button or DISP.
If you turn off the ignition or radio with a disc in the
player, it will stay in the player. When you turn on the
ignition or system, the disc will start playing where it
stopped, if it was the last selected audio source.

3-26
Cassette Tape Messages
If an error message appears while trying to play
a cassette tape, it could be for one of the
following reasons:
TIGHT TAPE: The tape is tight and the player can't
turn the tape hubs. Remove the tape. Hold the tape with
the open end down and try to turn the right hub
counterclockwise with a pencil. Turn the tape over and
repeat. If the hubs do not turn easily, your tape may be
damaged and should not be used in the player. Try a new
tape to make sure your player is working properly.
BROKEN TAPE: The tape is broken. Try a new tape.
CLEAN PLAYER: If this message appears on the
display, the cassette tape player needs to be cleaned. It
will still play tapes, but you should clean it as soon as
possible to prevent damage to the tapes and player. See
ªCare of Your Cassette Tape Playerº in the Index.
If any error occurs repeatedly or if an error can't be
corrected, contact your dealer. If your radio displays an
error number, write it down and provide it to your dealer
when reporting the problem.Playing a Compact Disc
Insert a disc partway into the slot, label side up. The
player will pull it in. The disc should begin playing. If
you want to insert a CD while the ignition or the radio is
off, first press the eject button or DISP.
If you turn off the ignition or radio with a disc in the
player, it will stay in the player. When you turn on the
ignition or system, the disc will start playing where it
stopped, if it was the last selected audio source.
If an error appears on the display, see ªCompact Disc
Messagesº later in this section.
1
(Reverse): Press and hold this pushbutton to
quickly reverse within a track. You will hear sound.
2
(Forward): Press and hold this pushbutton to
quickly advance within a track. You will hear sound.
4 RDM (Random): Press this button to hear the tracks
in random, rather than sequential, order. Press RDM
again to turn off random play.

3-34
To load more than one disc but less than six, complete
Steps 1 through 3. When you have finished loading
discs, with the radio on or off, press the LOAD side of
the LOAD CD button to cancel the loading function.
The radio will begin to play the last CD loaded.
When a disc is inserted, the CD symbol will be
displayed. If more than one disc has been loaded, a
number for each disc will be displayed. If you select an
equalization setting for your disc, it will be activated
each time you play a disc.
If the radio is on or off, the last disc loaded will begin
to play automatically.
As each new track starts to play, the track number will
appear on the display.
Playing a Specific Loaded Compact Disc
For every CD loaded, a number will appear on the radio
display. To play a specific CD, first press the CD AUX
button to start playing a CD. Then press the numbered
pushbutton that corresponds to the CD you want to play.
A small bar will appear under the CD number that is
playing, and the track number will appear.
If an error appears on the radio display, see ªCompact
Disc Messagesº later in this section.LOAD CD(Eject): The CD eject side of this button
will eject a disc or discs, if you have multiple discs
loaded. To eject a disc or discs from the disc player,
perform one of the following steps:

Press and release the CD eject side of the LOAD CD
button to eject the disc that is currently playing, or

to eject all of the discs, press the CD eject side of the
LOAD CD button for two seconds, you will hear a
beep, and the light will flash to let you know when
a disc is being ejected.
When the CD eject side of the LOAD CD button is
pressed, the receiver will eject the disc and REMOVE
CD will be displayed. You can now remove the disc.
If the disc is not removed, after 25 seconds, the disc
will be automatically pulled back into the receiver. If
you try to push the disc back into the receiver, before
the 25 second time period is complete, the receiver will
sense an error and will try to eject the disc several times
before stopping.
Do not repeatedly press the CD eject side of the LOAD
CD eject button to eject a disc after you have tried to
push it in manually. The receivers 25
-second eject timer
will reset at each press of eject, which will cause the
receiver to not eject the disc until the 25
-second time
period has elapsed.

3-35
Once the player stops and the disc is ejected, remove
the disc. After removing the disc, press the PWR knob
off and then on again. This will clear the disc
-sensing
feature and enable discs to be loaded into the
player again.
<< REV (Reverse): Press and hold this button to
reverse quickly within a track. Release it to play the
passage. You will hear sound at a reduced volume.
The display will show elapsed time.
FWD >> (Forward): Press and hold this button to
advance quickly within a track. Release it to play the
passage. You will hear sound at a reduced volume.
The display will show elapsed time.
RPT (Repeat): With repeat, you can repeat one track
or an entire disc. To use repeat, do the following:

To repeat the track you are listening to, press and
release the RPT button. RPT will appear on the
display. Press RPT again to turn it off.

To repeat the disc you are listening to, press and hold
the RPT button for two seconds. RPT will appear on
the display. Press RPT again to turn if off.RDM (Random): With random, you can listen to
the tracks in random, rather than sequential order,
on all of the discs or on one disc. To use random,
do the following:

To play the tracks on the disc you are listening to in
random order, press and hold RDM for more than
two seconds. You will hear a beep and RDM will
appear on the display. Press RDM again to turn if
off. Or,

press and release the RDM button to play the tracks
on all of the discs that are loaded, in random order.
RDM will appear on the display. Press RDM to turn
it off.
AUTO EQ (Automatic Equalization): Press AUTO
EQ to select the desired preset equalization setting
while playing a compact disc. The equalization will be
automatically set whenever you play a compact disc.
For more information on AUTO EQ, see ªAUTO EQº
listed previously in this section.


SEEK: To seek, press the left arrow while playing
a CD to go to the start of the current track, if more than
ten seconds have passed. Press the right arrow to go to
the next track. If you press the button more than once,
the player will continue moving backward or forward
through the disc.

3-39
Rear Seat Radio Controls
The following functions are controlled by the RSA
system buttons:
PWR (Power): Press this button to turn RSA on or off.
VOL (Volume): Press this knob lightly so it extends.
Turn the knob clockwise to increase volume and
counterclockwise to decrease volume. Push the knob
back into its stored position when you're not using it.
The upper VOL knob controls the left headphone and
the lower VOL knob controls the right headphone.AM FM: Press this button to switch between AM, FM1
and FM2. If the front passengers are already listening to
AM or FM, the RSA controller will not switch between
the bands and cannot change the frequency. Press this
button to play a cassette tape or a compact disc when
listening to the radio.
SEEK : While listening to AM FM, press the up
or down arrow to tune to the next or previous station and
stay there. The sound will mute while seeking. The
SEEK button is inactive if the AM FM mode on the
front radio is in use.
While listening to a cassette tape, press the up arrow to
hear the next selection on the tape. Press the down arrow
to go back to the previous selection. The SEEK button is
inactive if the tape mode on the front radio is in use.
While listening to a CD, press the up arrow to hear the
next selection on the CD. Press the down arrow to go
back to the start of the current selection (if more than
eight seconds have played). The SEEK button is inactive
if the CD mode on the front radio is in use.
To scan stations, press and hold one of the SEEK arrows
until the radio goes into scan mode. The radio will scan
to a station, play for a few seconds, then go on to the
next station. Press SEEK again to stop scanning. The
scan function is inactive if the AM
-FM mode on the
front radio is in use.