ESP BUICK RANDEZVOUS 2007 Owner's Manual

Heated Seats
Your vehicle may have
heated seats. If it does,
the heated seat
switches are located in
the instrument panel
switchbank.
This feature will quickly heat the seat cushions
and lower back of the driver’s and front
passenger’s seat. The left switch is for the driver’s
seat and the right switch is for the front
passenger’s seat.
Press the top of the switch to turn the heater on.
Press the bottom of the switch to turn the
heater off. The heated seat switch will turn off
when the ignition is turned to OFF and will resume
operation when the ignition is turned to ON,
unless the switch is turned off.
Memory Seat and Mirrors
If your vehicle has this
feature, the controls are
located on the driver’s
door panel and are used
to store and recall the
driver’s seat position
and the outside rearview
mirror position.
The settings for these features can be
personalized for both driver 1 and driver 2.
Driver 1 and driver 2 correspond to the memory
buttons labeled 1 and 2 on the driver’s door and to
the numbers, 1 or 2, on the back of the remote
keyless entry transmitters.
11

To store the memory settings, do the following:
1. Adjust the driver’s seat and the outside
rearview mirrors to the position you would like
for driving.
2. Press and hold memory button 1 for more
than three seconds.
A double beep will sound when the memory seat
and mirror position have been stored.
To store the seat and outside rearview mirror
positions for a second driver, follow the previous
steps, but press button 2 instead.
To recall your stored positions, your vehicle must
be in PARK (P). Press and release the memory
button (1 or 2) corresponding to the desired driving
position. The seat and the outside rearview
mirrors will move to the position previously stored
for the identied driver. You will hear one beep.To store an exit position for each driver, do the
following:
1. Move the seat to the desired exit position.
2. Hold the button with the exit symbol, located
below the memory buttons, for more than
three seconds.
The exit position stored will be for the most
recently selected driving position (1 or 2). A double
beep will sound when the exit position is stored.
To use the exit feature, your vehicle must be
in PARK (P). Press and release the button with
the exit symbol and the seat will move to the exit
position stored for the most recently selected
driver. You will hear one beep.
To stop recall movement of the seat at any time,
press one of the three memory buttons or one
of the power seat controls located on the outboard
side of the driver’s seat.
If your vehicle is equipped with a Driver
Information Center (DIC), you can use it to
program certain functions of the memory seats.
SeeDIC Vehicle Personalization on page 240.
12

or the safety belts!
With safety belts, you slow down as the vehicle
does. You get more time to stop. You stop
over more distance, and your strongest bones
take the forces. That is why safety belts
make such good sense.
Questions and Answers About
Safety Belts
Q:Will I be trapped in the vehicle after an
accident if I am wearing a safety belt?
A:Youcouldbe — whether you are wearing a
safety belt or not. But you can unbuckle a
safety belt, even if you are upside down. And
your chance of being conscious during and
after an accident, so youcanunbuckle and get
out, ismuchgreater if you are belted.
Q:If my vehicle has airbags, why should I
have to wear safety belts?
A:Airbags are in many vehicles today and will be
in most of them in the future. But they are
supplemental systems only; so they workwith
safety belts — not instead of them. Every
airbag system ever offered for sale has
required the use of safety belts. Even if you
are in a vehicle that has airbags, you still have
to buckle up to get the most protection. That
is true not only in frontal collisions, but
especially in side and other collisions.
34

Doors and Locks
Door Locks
{CAUTION:
Unlocked doors can be dangerous.
Passengers, especially children, can
easily open the doors and fall out of a
moving vehicle. When a door is
locked, the handle will not open it.
You increase the chance of being
thrown out of the vehicle in a crash if
the doors are not locked. So, wear
safety belts properly and lock the
doors whenever you drive.
CAUTION: (Continued)
CAUTION: (Continued)

Young children who get into unlocked
vehicles may be unable to get out.
A child can be overcome by extreme
heat and can suffer permanent injuries
or even death from heat stroke.
Always lock your vehicle whenever
you leave it.
Outsiders can easily enter through an
unlocked door when you slow down
or stop your vehicle. Locking your
doors can help prevent this from
happening.
There are several ways to lock and unlock your
vehicle.
From the outside, use your key or the remote
keyless entry transmitter.
114

Windows
{CAUTION:
Leaving children, helpless adults, or pets
in a vehicle with the windows closed is
dangerous. They can be overcome by the
extreme heat and suffer permanent
injuries or even death from heat stroke.
Never leave a child, a helpless adult, or a
pet alone in a vehicle, especially with the
windows closed in warm or hot weather.
120

Sun Visors
To block out glare you can swing down the visors.
You can also remove them from the center
mount and swing them to the side. There may be
an extension on the inboard side of the sun
visors. Pull the extension out to block out glare.
Visor Vanity Mirror
Pull down the sun visor. Flip up the cover to
expose the vanity mirror.
Lighted Visor Vanity Mirrors
If your vehicle has this feature, pull down the sun
visor. Flip up the cover to expose the vanity
mirror. The lamps will come on when you open
the cover.
Theft-Deterrent Systems
Vehicle theft is big business, especially in some
cities. Although your vehicle has a number of
theft-deterrent features, we know that nothing we
put on it can make it impossible to steal.
Content Theft-Deterrent
Your vehicle may have a theft-deterrent alarm
system.
A security light, located
on top of the instrument
panel will ash slowly
to let you know that the
system has been
armed.
While armed, the doors will not unlock with the
power door lock switch.
Once armed, the alarm will go off if someone tries
to enter the vehicle without using the optional
remote keyless entry transmitter or the key, or tries
to turn the ignition on without using the correct
key. The horn will sound and the headlamps and
parking lamps will ash any time the alarm
sounds.
122

OnStar®service that involves location information
about your vehicle cannot work unless GPS
satellite signals are unobstructed and available in
that place as well.
Your vehicle must have a working electrical
system (including adequate battery power) for the
OnStar
®equipment to operate. There are other
problems OnStar®cannot control that may prevent
OnStar®from providing OnStar®service to you
at any particular time or place. Some examples are
damage to important parts of your vehicle in an
accident, hills, tall buildings, tunnels, weather
or wireless phone network congestion.
Your Responsibility
You may need to increase the volume of your
radio to hear the OnStar®advisor. If the light next
to the OnStar®buttons is red, this means that
your system is not functioning properly and should
be checked by a dealer. If the light appears
clear (no light is appearing), your OnStar
®
subscription has expired. You can always press
the blue OnStar®button to conrm that your
OnStar®equipment is active.
Universal Home Remote
System
Universal Home Remote System
(With Three Round LED)
The Universal Home Remote System provides a
way to replace up to three hand-held
Radio-Frequency (RF) transmitters used to
activate devices such as garage door openers,
security systems, and home lighting.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
The FCC Grant of Equipment Authorization
Certicate number is KOBGTE05A.
147

<(Parking Lamps):Turning the control to this
position turns on the parking lamps together
with the following:
Taillamps
Instrument Panel Lights
5(Headlamps):Turning the control to this
position turns on the headlamps together with the
previously listed lamps and lights.
Lamps on Reminder
If the driver’s door is opened and you turn the
ignition to OFF while leaving the lamps on, you will
hear a warning chime.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during
the day. DRL can be helpful in many different
driving conditions, but they can be especially
helpful in the short periods after dawn and before
sunset. Fully functional daytime running lamps
are required on all vehicles rst sold in Canada.A light sensor on top of the instrument panel
makes the DRL work, so be sure it is not covered.
The DRL system will make your reduced
intensity low-beam headlamps come on in daylight
when the following conditions are met:
The ignition is on.
The exterior lamps control is in AUTO.
The shift lever is not in PARK (P).
When the DRL are on, only your reduced intensity
high-beam headlamps will be on. Your instrument
panel will not be lit up.
When it is dark enough outside, the exterior lamps
will come on automatically. When it is bright
enough outside, the exterior lamps will go out and
the DRL will turn on. Of course, you may still
turn on the headlamps any time you need to.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
186

DIC Controls and Displays
When the ignition is turned to ON or START, the
DIC will display the following:
BUICK:BUICK will be displayed for three
seconds.
DRIVER #:This message will be displayed for
another three seconds after BUICK appears in the
display. The driver number corresponds to the
numbers, 1 or 2, on the back of the Remote
Keyless Entry (RKE) transmitters. This display lets
the driver know which driver’s RKE transmitter
is being used and the driver’s customization
features.
The DIC controls are
located to the left of the
steering column on
the instrument panel.The DIC will be in the last mode displayed when
the engine was turned off. To select a different
mode, press MODE. The display will cycle through
its options at each press of MODE.
MODE:This button lets you cycle through the
options on the display.
SET:This button is used to select and set the
options to your preference.
The DIC will always display the compass reading
and the outside temperature. If the temperature
is below 38°F (3°C), the temperature reading will
toggle between displaying the temperature and
the word ICE for two minutes.
AVG ECONOMY (Average Economy):Average
fuel economy is viewed as a long term
approximation of your overall driving conditions.
To learn the average fuel economy from a
new starting point, press and hold the SET button
while the average fuel economy is displayed on
the DIC. The average fuel economy will set
to zero.
236

DIC Vehicle Personalization
The DIC is used to program the choices of
two drivers. The drivers are recognized as
DRIVER 1 or DRIVER 2 in the DIC display. You
will let the DIC know which driver you are by using
your Remote Keyless Entry (RKE) transmitter.
Each RKE transmitter was pre-programmed
to belong to DRIVER 1 or DRIVER 2 and the
corresponding numbers, 1 or 2, appear on
the back of the transmitters. Each transmitter may
be programmed differently for each driver’s
preferences (lights, doors, horn, or activate the
programmed radio stations for driver 1 or driver 2)
using your RKE transmitter.
After you press the LOCK button on your RKE
transmitter and the ignition key is in ON, the DIC
will display the identied driver number. The
vehicle will also recall the vehicle customization
features that were last programmed to correspond
to your RKE transmitter.
If you unlock your vehicle using your key instead
of your RKE transmitter, the DIC will not change
drivers and your vehicle will recall the information
from the last transmitter used.If your vehicle does not have a DIC, you do not
have available the vehicle customization features
using the RKE transmitter.
Entering Programming Mode
To program features, your vehicle must be in the
programming mode. Do the following:
1. Turn the ignition key to ON with the vehicle in
PARK (P).
To avoid excessive drain on the battery, it is
recommended that the headlamps are
turned off.
2. Press and release the MODE button, scrolling
through the DIC messages, until
PERSONALIZATION PRESS SET TO BEGIN
is displayed.
3. Press the SET button and TO SELECT
DRIVER PRESS REMOTE LOCK will appear.
Press the LOCK button on the Remote Keyless
Entry (RKE) transmitter. This identies which
RKE transmitter is being programmed by
displaying PERSONALIZATION FOR
DRIVER 1 or DRIVER 2.
240