headlamp BUICK REGAL 1997 Owners Manual

Security Feedback
Security Feedback provides audible and/or visible
feedback that a remote keyless entry lock or unlock
command has been received and executed. Your
vehicle’s ignition must be off for this feature to work.
You may select
one of four operating modes for
reception of a lock command. You may also select one
of four operating modes for reception
of an unlock
command. The selection and programming of the lock
and unlock operating modes are independent of each
other. The following modes are available for either lock
or unlock verification:
Mode
1: No Verification
Mode
2: Horn Chirp only
Mode
3: Headlamp Flash only
Mode
4: Horn Chirp and Headlamp Flash
The operating mode
of the Security Feedback lock
function will be changed when you
perform the following
sequence with your vehicle’s doors closed and the ignition
key in
RUN:
Press and hold the power door lock switch. While
holding the door lock switch, press and release the
remote keyless entry
(RKE) transmitter lock switch.
This will initialize the customization mode. While in the
customization mode, the chime will sound the number
of chimes corresponding to the current Security
Feedback lock mode. Each additional press of the
RKE
transmitter lock switch will cause your vehicle to
advance the lock mode by
one, starting from the current
lock mode. If cycled beyond lock Mode
4, the vehicle
will enter lock Mode
1. During this procedure, the
chime will sound the number of chimes corresponding
to the current lock mode, providing you with feedback.
When the door lock switch is released, the vehicle will
remain in the most recent lock mode.
The operating mode of the Security Feedback unlock
function will be changed when you perform the
following sequence with your vehicle’s doors closed and
the ignition key in
RUN:
2-11
ProCarManuals.com

Press and hold the power door unlock switch. While
holding the door unlock switch, press and release the
RKE transmitter unlock switch. This will initialize the
customization mode. While in the customization mode,
the chime will sound the number of chimes
corresponding to the current Security Feedback unlock
mode. Each additional press
of the RKE transmitter
unlock switch will cause your vehicle to advance the
unlock mode by one, starting from the current unlock
mode. If cycled beyond unlock Mode
4, the vehicle will
enter unlock Mode
1. During this procedure, the chime
will sound the number of chimes corresponding to the
current unlock mode, providing you with feedback.
When the door unlock switch is released, the vehicle
will remain in the most recent unlock mode.
Both the lock and unlock
Security Feedback functions will
be in operating Mode
4 when the vehicle is shipped from
the factory.
Disconnecting the vehicle’s battery for up to a year will
not change the programmed mode of the lock and
unlock Security Feedback functions.
Illumination on Remote Activation
This feature provides interior illumination when a remote
keyless entry door unlock command
is received and
executed by
your vehicle. Your vehicle’s ignition must be
off for the Illumination on Remote Activation feature to
work. The interior lamps will illuminate until your
vehicle’s ignition is turned to the RUN position or until
an illumination period of 40 seconds has elapsed. If a
door
is opened during the illumination period, the timed
illumination will be canceled, and the interior lamps will
remain on since a door
is open.
Instant Alarm
This feature allows you to activate an alarm by pressing
a switch on the remote keyless entry transmitter. Your
vehicle’s ignition must be off for the Instant Alarm to
work. When you press the special horn button on the
remote keyless entry transmitter, your vehicle’s
headlamps will flash, the
horn will honk repeatedly, and
your interior lamps will illuminate, attracting attention if
you need
it. The alarm will continue until:
1. You press the alarm button on the RISE transmitter a
second time.
2. The vehicle’s ignition is turned to the RUN position.
3. An alarm period of about two minutes has elapsed.
ProCarManuals.com

Turn SignaVMultifunction Lever
The lever on the left side of the steering column
includes your:
0 Turn Signal and Lane Change Indicator
Headlamp High/Low Beam
0 Windshield Wipers
0 Windshield Washer
0 Cruise Control
0 Flash-to-Pass
Turn Signal and Lane Change Indicator
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow
you to signal a turn or
a lane change.
To signal a turn, move the lever all the way up or down.
When the turn
is finished, the lever will return
automatically.
An arrow on the instrument
panel will flash in
the
direction of the turn or
lane change.
To signal a lane change, just raise or lower the lever
until
the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release
it.
ProCarManuals.com

As you signal a turn or a lane change, if the arrow
flashes faster than normal, a signal bulb may be
burned out and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to
help avoid an
accident. If the arrows don’t go on at all when you
signal a turn, check for burned-out bulbs and then check
the fuse (see “Fuses and Circuit Breakers” in the Index).
A chime will sound if you leave your turn signal on for
more than
3/4 mile (1.2 km).
Headlamp HigWLow Beam
To change your headlamps
from low beams to high
beams, or high to low, pull
the multifunction lever all
the way toward you. Then
release it. When the high
beams are on, a light on the
instrument panel also will
be on.
Flash-to-Pass Feature
This feature lets you use your high-beam headlamps to
signal
the driver in front of you that you want to pass. It
works even if your headlamps are off.
To use it, pull the turn signal lever toward you a little,
but not
so far that you hear a click.
If your headlamps are off or on low beam, your
high-beam headlamps will turn
on. They’ll stay on as
long as
you hold the lever toward you and the
high-beam indicator on the dash will come on. Release
the lever to turn
the high-beam headlamps off.
2-36
ProCarManuals.com

Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness
of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift
to a lower gear
to keep your speed down.
Of course, applying the brake
takes
you out of cruise control. Many drivers find this to
be too much trouble and don’t use cruise control on
steep hills.
Ending Cruise Control
There are two ways to turn off the cruise control:
0 Step lightly on the brake pedal; OR
0 Move the cruise switch to OFF.
Erasing Cruise Speed Memory
When you turn off the cruise control or the ignition, or
shift into
PARK (P) or NEUTRAL (N), your cruise
control set speed memory is erased.
Exterior Lamps
The lamp controls are located on the instrument panel.
They control these systems:
Headlamps
Taillamps
Parklarnps
License Lamps
0 Sidemarker Lamps
0 Instrument Panel Lamps
Courtesy Lamps
Fog Lamps
0 Cornering Lamps
ProCarManuals.com

If you pull the knob out
halfway,
it will turn on only
your parklamps. If you pull
the knob all the way out,
your headlamps
will then
come on.
Push the knob
in all the way to turn off the lamps.
A warning chime will sound if you open the driver’s
door when you turn the ignition switch to
OFF, LOCK
or
ACC with the lamps on.
Daytime Running Lamps / Automatic
Headlamp Control
Daytime Running Lamps (DRL) can make it easier for
others to see the front
of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful
in the
short periods after dawn and before sunset.
A light sensor on top of the instrument panel makes the
DRL work,
so be sure it isn’t covered.
The DRL system will make your front turn signal lamps
come on when:
0 The ignition is on,
0 The headlamp switch is off and
0 The parking brake is released.
When the DRL are on, only your front turn signal lamps
will be on. The headlamps, taillamps, sidemarker and
other lamps won’t be on. Your instrument panel won’t
be lit up either.
When it’s dark enough outside, your front turn signal
lamps will turn off and your vehicle’s headlamps and
parklamps will turn
on. The other lamps that come on
with your headlamps will also come on.
When it’s bright enough outside, your headlamps will
go
off and your front turn signal lamps will come on.
To idle your vehicle with the DRL off, set the parking
brake while
the ignition is in OFF or LOCK. Then start
your vehicle. The DRL, headlamps and parklamps will
stay off until you release the parking brake.
As with any vehicle, you should turn on the regular
headlamp system when you need
it.
2-42
ProCarManuals.com

Twilight Sentinel
Twilight Sentinel provides a period of exterior
illumination as you leave the vicinity
of your vehicle.
The feature is activated when your vehicle’s headlamps
are on due to the automatic headlamp control feature
described previously in this section, and when your
vehicle’s ignition is turned
off. Your headlamps will
then remain on until the headlamp switch is moved from
OFF to the parklamp position or until a 90 second
illumination period has elapsed.
If you turn off the ignition with the headlamp switch in
the parklamp or headlamp position, the Twilight
Sentinel cycle will
not occur.
You can customize the vehicle to activate the Twilight
Sentinel when your vehicle’s ignition is turned off under
the conditions described above, or you may choose
not
to activate this feature under any conditions. The
enabledldisabled state of this feature will be toggled
when you perform the following sequence with the
doors closed and the ignition key in the
RUN position: Press
and hold the power door lock switch. While
holding the door lock switch, cycle the headlamp switch
on and then
off two times. Release the power door lock
switch. These operations must be carried out
in a time
period
of less than 10 seconds, followed by a delay
period
of no more than 10 seconds. Then, press and hold
the power door unlock switch. While holding the door
unlock switch, cycle the headlamp switch on and then
off two times. Release the courtesy door unlock switch.
These operations must be carried out in a time period of
less than 10 seconds.
After releasing the door unlock switch, a single chime
will be heard if the Twilight Sentinel function has been
disabled; two chimes will be heard if the feature has
been enabled. This feature will be enabled when your
vehicle is shipped from the factory. Disconnecting the
vehicle’s battery for up to a year will not change the
programmed operation of this feature.
2-43
ProCarManuals.com

Fog Lamps
To turn the fog lamps on,
press the fog lamps switch
located below the headlamp
switch
on the left side of the
steering column.
A light
will glow on the switch to
let you know that
they are
on. (Your parklamps must
be on or your fog lamps
won’t come on). Press the
switch again
to turn the fog
lamps off.
The fog lamps will go off whenever you change to
high-beam headlamps. When you return to low beams,
the fog lamps will come on again.
Cornering Lamps
The cornering lamps are designed to come on when you
signal a turn. This will provide more light for cornering
at night.
Interior Lamps
Instrument Panel Brightness Control
You can brighten or dim the instrument panel lights by
moving the LIGHTS dial. If you turn the dial past
MAX, your courtesy or interior lamps will come on.
Courtesy Lamps
When any door is opened, several lamps come on. These
lamps are courtesy lamps. They make it easy for you to
enter and leave your vehicle. You can also turn these
lamps on by moving the interior lamps dial all the way
to the right.
Illuminated Entry
Your courtesy lamps will come on and stay on for a set
time whenever you press
UNLOCK on the remote
keyless entry transmitter.
If
you open a door, the lamps will stay on while it’s open
and then turn off automatically about
25 seconds after
you close it. If you press
UNLOCK and don’t open a
door, the lamps will turn off after about
40 seconds.
2-44
ProCarManuals.com

Mirrors
Adjust all the mirrors so you can see clearly when YOU
are sitting in a comfortable driving position.
Inside Daymight Rearview Mirror Electrochromic
Daymight Rearview Mirror
(If Equipped)
To reduce glare from lamps behind you, pull the lever
toward
you (to the night position). To return the mirror
back to the day position, push the lever away from
you.
Your Buick may have an electrochromic dayhight
rearview mirror.
Push the button in the center of the
mirror to turn
this feature on. The mirror will darken
gradually
to reduce glare from headlamps behind you.
This may take
a few moments.
2-47
ProCarManuals.com

~ The mirror’s two outer buttons operate the lights on
~ the bottom sides of the mirror.
~ One photocell on the front of the mirror senses when
it is becoming dark outside. Another photocell, facing
rearward, senses headlamps behind you. To turn the electrochromic feature
off, press the button in the
center of the mirror again.
To keep the photocells operating well, occasionally
clean them with a cotton swab and glass cleaner.
Power Outside Mirrors
The power mirror control
switches are located near the
driver’s side window, on the
armrest.
To choose either the
left or right outside
mirror,
move the top switch from
left through neutral to right.
Press any of the four buttons
located below the top switch
to move the mirrors
in the
desired direction.
Heated Foldaway Outside Mirrors
The left and right outside mirrors are heated when you
activate the rear window defogger.
These mirrors can also be folded forward manually. This
feature
is particularly useful in automatic car washes and
when maneuvering your vehicle in narrow spaces.
Co-- -- - -: Outside Mirror
Your passenger’s side mirror is convex. A convex
mirror’s surface is curved
so you can see more from
the driver’s seat.
J I1U.
A convex mirror can make things (like other
vehicles) look farther away than they really are.
If you cut too sharply into the right lane, you
could hit
a vehicle on your right. Check your
inside mirror or glance over your shoulder
before changing lanes.
Adjust each mirror so you can see the side of your
vehicle and the area behind your vehicle.
2-48
ProCarManuals.com