keyless CADILLAC CTS 2003 1.G User Guide

2-16
Trunk Lid
CAUTION:
It can be dangerous to drive with the trunk lid
open because carbon monoxide (CO) gas can
come into your vehicle. You can't see or smell
CO. It can cause unconsciousness and even death.
If you must drive with the trunk lid open or if
electrical wiring or other cable connections must
pass through the seal between the body and the
trunk lid:

Make sure all other windows are shut.

Turn the fan on your heating or cooling
system to its highest speed and select the
control setting that will force outside air
into your vehicle. See ªComfort Controlsº
in the Index.

If you have air outlets on or under the
instrument panel, open them all the way.
See ªEngine Exhaustº in the Index.
Remote Trunk Release Button
The remote trunk release
button is located on the
lower portion of the
driver's door.
To use this feature, an automatic transmission must
be in PARK (P) or NEUTRAL (N) and your manual
transmission must be in NEUTRAL with the parking
brake set.
Press the button to open the trunk. You can also press
the button with the trunk symbol on the remote keyless
entry transmitter to open the trunk.
When the trunk lid opens, a light inside the trunk
will come on. The light will go out when the trunk
lid is closed.

2-20
Theft-Deterrent System
The security light is located
on the instrument panel
cluster.
If the ignition is off and a door is open, the security light
will flash, reminding you to arm the theft
-deterrent
system.
To arm the system, do the following:
1. Open the door.
2. Lock the door using the remote keyless entry
transmitter or the power door lock switch. The
security light should come on and stay on.
3. Close all the doors. The security light should go off
within approximately 30 seconds.
If a door or a trunk is opened without a key or a remote
keyless entry transmitter, the horn will sound and the
lamps will flash for up to 30 seconds.The theft
-deterrent system won't arm if you lock the
doors with a key or use the manual door lock. It
activates only if you use the remote keyless entry
transmitter.
To avoid activating the alarm by accident do the
following:

The vehicle should be locked with the door key or
the manual door lock after the doors are closed if
you don't want to arm the theft
-deterrent system.

Always unlock a door with a key or use the remote
keyless entry transmitter. Pressing the unlock button
on the remote keyless entry transmitter disables the
theft
-deterrent system. Unlocking a door any other
way will activate the alarm when a door or the trunk
is opened.
If you activate the alarm by accident, unlock the driver's
door with your key. You can also turn off the alarm by
using the unlock button on the remote keyless entry
transmitter, or by starting the vehicle with a valid key.

2-21
Testing the Alarm
1. From inside the vehicle, roll down the window, then
get out of the vehicle, keeping the door open.
2. From outside of the vehicle, with the door open, lock
the vehicle using the power door lock switch or the
remote keyless entry transmitter and close the door.
Wait approximately 30 seconds until the security
light goes off.
3. Reach in and unlock the door using the manual lock
and open the door. The horn will sound and the
exterior lamps will flash.
You can turn off the alarm by unlocking the driver's
door with your key, using the unlock button on the
remote keyless entry transmitter or by starting the car
with a valid key.
If the alarm does not sound when it should, check to see
if the horn works. The horn fuse may be blown. To
replace the fuse, see ªFuses and Circuit Breakersº in the
Index. If the fuse does not need to be replaced, you may
need to have your vehicle serviced.
To reduce the possibility of theft, always arm the
theft
-deterrent system when leaving your vehicle.
Immobilizer
Your vehicle is equipped
with a passive
theft
-deterrent system.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.

2-59
Interior Lamps
Instrument Panel Brightness Lever
This feature controls the brightness of the instrument
panel lights.
The lever for this feature
is located on the
overhead console.
Slide the lever toward the symbol to brighten the lights
or away from it to dim them.
If you slide the lever all the way toward the symbol past
the resistance point, the interior lamps will come on. To
turn them off, slide the lever back toward the minimum
brightness setting.
Illuminated Entry
The illuminated entry system turns on the reading and
dome lamps and the backlighting to the exterior lamp
control when a door is opened or if you press the remote
keyless entry transmitter unlock button. If activated by
the transmitter, the lighting will remain active for about
25 seconds. The illuminated entry system uses the light
sensor, it must be dark outside in order for the lamps to
turn on. The lamps turn off approximately 25 seconds
after the last door is closed. They will dim to off if the
ignition key is placed in ON, or immediately deactivate
if the power locks are activated.
Parade Dimming
This feature prohibits dimming of the instrument panel
displays and backlighting during daylight hours when
the key is in the ignition and the headlamps are on.
This feature operates with the light sensor and is fully
automatic. When the light sensor reads darkness outside
and the parking lamps are active, the instrument panel
displays can be adjusted by sliding the instrument panel
brightness lever toward the symbol to brighten or away
from the symbol to dim the lighting.

2-115
Passenger Door Ajar
This symbol appears
with the Passenger Door
Ajar message.
When this message appears on the display, it means
that the passenger's side front door was not closed
completely. You should make sure that the door is
closed completely.Personalization Off/Driver Identification
(Navigation System Only)
This symbol appears
with the Personalization
Off message.
When this message appears, the personalization features
previously stored are turned off. If you want your
customized settings to be automatically recalled when
you use the remote keyless entry transmitter or when
you remove the key from the ignition, you must enable
them in the DIC. See ªVehicle Programming and
Personalization Featuresº later in this section for more
information.
This message is also used to identify the
driver (1, 2 or 3) on the Navigation system.

2-130
Vehicle Programming and
Personalization Features
Your vehicle is equipped with personalization that
allows you to program certain features to a preferred
setting for up to two people. The number of
programmable features varies depending upon which
model of the vehicle is purchased.
On all vehicles, features such as climate control settings,
radio preset settings, exterior lighting at unlock, remote
lock and unlock confirmation, and automatic door locks
have already been programmed for your convenience.
Some vehicles are equipped with additional features that
can be programmed including the seat and outside
rearview mirror position. The optional navigation
system screen preferences will remain at the last set
position.
If your vehicle is equipped with the ability to program
additional personalization features, the driver's
preferences are recalled by pressing the unlock button
on the remote keyless entry transmitter, 1 or 2, or
by pressing the appropriate memory button, 1 or 2,
located on the driver's door. Certain features can be
programmed not to recall until the key is placed in the
ignition. To change feature preferences you must use
one of the following procedures.
Entering the Personalization Menu
To enter the feature programming mode, use one of the
following procedures:
Base Audio System
1. Turn the ignition to ON, but do not start the engine.
Make sure an automatic transmission is in PARK (P)
or a manual transmission has the parking brake set.
2. If your vehicle has memory settings, press the
appropriate memory button, 1 or 2, located on the driver's
door armrest. The DIC display will show either Driver 1
or 2 depending on which button was selected.
3. Press the TUNE/SEL knob once to access the main
menu of the DIC.
4. Turn the TUNE/SEL knob until SETUP is highlighted.
5. Press the TUNE/SEL knob once to access the
SETUP menu.
6. Scroll to the feature you want to change, and press
the TUNE/SEL knob to turn the feature on or off.
If the feature is turned on, a check mark will appear
next to the feature name.
If none of the personalization items are turned on,
turn on the personalization menu by pressing the
TUNE/SEL knob. The list of features will then
appear, and you can repeat Step 6.

2-131
Navigation System
1. Turn the ignition to ON without the engine running.
Make sure an automatic transmission is in PARK (P)
or a manual transmission has the parking brake set.
2. Turn on the Navigation/audio system by pressing the
PWR/VOL knob located to the lower left of the
display once.
3. Access the DIC main menu by pressing the MAIN
button located to the lower left of the display.
4. Press the multi
-function button next to Feat Prog to
access the Feature Programming menu.
5. Press the TUNE/SEL knob to turn on the
Personalization features. An X will appear in the box
to the left when Personalization is turned on.
Personalization Features
The following choices are available for programming
using both the Base audio and Navigation systems
unless otherwise indicated.
Personalization Name
This feature allows you to type in a name that will
appear on the DIC display whenever the corresponding
remote keyless entry transmitter is used or one of the
buttons on the driver's door armrest (1 or 2) is pressed.
If a customized name is not programmed, the system
will show Driver 1 or Driver 2 to correspond with the
numbers on the back of the remote keyless entry
transmitters.
To program a name, use one of the following
procedures:

2-133
Configure Display Keys (Base Audio System Only)
This feature allows you to customize the functions of
the four soft keys located to the left and right of the
audio display. Most of the available functions are
audio
-system related. See ªAudio Systemsº in the
Index for more information.
Remote Recall Memory/Recall Driving Positions
(If Equipped)
This feature recalls any previously programmed seat and
mirror controls when the unlock button on the remote
keyless entry transmitter is pressed.
Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 2. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.2. Scroll to REMOTE RECALL MEMORY to
highlight it.
3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, a check mark will
appear next to the feature name.
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Remote Keyless Options to highlight it.
3. Press the TUNE/SEL knob to view the modes.
4. Scroll to Recall Driving Positions and press the knob
once to select it.
When the mode is turned on, an X will appear in the
box to the left.
If Remote Exit Recall or Key In Recall Memory were turned
on previously, selecting Remote Recall Memory/Recall
Driving Positions will override that choice.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-134
Remote Exit Recall (If Equipped)
This feature allows any previously programmed exit
position for the driver's seat to be recalled when the
unlock button on the remote keyless entry transmitter is
pressed.
Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 2. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to REMOTE EXIT RECALL to highlight it.3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, a check mark will
appear next to the feature name.
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Remote Keyless Options to highlight it.
3. Press the TUNE/SEL knob to view the modes.
4. Scroll to Remote Exit Recall and press the knob once
to select it.
When the mode is turned on, an X will appear in the
box to the left.
If Remote Recall Memory/Recall Driving Positions was
turned on previously, selecting Remote Exit Recall will
override that choice.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-135
Key in Recall Memory (If Equipped)
This feature recalls any previously programmed seat
and mirror positions when the key is inserted into the
ignition.
Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 2. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to KEY IN RECALL MEMORY to
highlight it.3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, a check mark will
appear next to the feature name.
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Remote Keyless Options to highlight it.
3. Press the TUNE/SEL knob to view the modes.
4. Scroll to Key In Recall Memory and press the knob
once to select it.
When the mode is turned on, an X will appear in the
box to the left.
If Remote Recall Memory/Recall Driving Positions was
turned on previously, selecting Key In Recall Memory
will override that choice.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.