turn signal CADILLAC CTS 2003 1.G Owner's Manual

4-21
City Driving
One of the biggest problems with city streets is the
amount of traffic on them. You'll want to watch out for
what the other drivers are doing and pay attention to
traffic signals.Here are ways to increase your safety in city driving:

Know the best way to get to where you are
going. Get a city map and plan your trip into an
unknown part of the city just as you would for a
cross
-country trip.

Try to use the freeways that rim and crisscross most
large cities. You'll save time and energy. See the
next part, ªFreeway Driving.º

Treat a green light as a warning signal. A traffic light
is there because the corner is busy enough to need it.
When a light turns green, and just before you start
to move, check both ways for vehicles that have
not cleared the intersection or may be running the
red light.

4-22
Freeway Driving
Mile for mile, freeways (also called thruways, parkways,
expressways, turnpikes or superhighways) are the safest
of all roads. But they have their own special rules.
The most important advice on freeway driving is: Keep
up with traffic and keep to the right. Drive at the same
speed most of the other drivers are driving. Too
-fast or
too
-slow driving breaks a smooth traffic flow. Treat the
left lane on a freeway as a passing lane.At the entrance, there is usually a ramp that leads to the
freeway. If you have a clear view of the freeway as you
drive along the entrance ramp, you should begin to
check traffic. Try to determine where you expect to
blend with the flow. Try to merge into the gap at close to
the prevailing speed. Switch on your turn signal, check
your mirrors and glance over your shoulder as often as
necessary. Try to blend smoothly with the traffic flow.
Once you are on the freeway, adjust your speed to the
posted limit or to the prevailing rate if it's slower. Stay
in the right lane unless you want to pass.
Before changing lanes, check your mirrors. Then use
your turn signal.
Just before you leave the lane, glance quickly over your
shoulder to make sure there isn't another vehicle in your
ªblindº spot.
Once you are moving on the freeway, make certain you
allow a reasonable following distance. Expect to move
slightly slower at night.
When you want to leave the freeway, move to the proper
lane well in advance. If you miss your exit, do not,
under any circumstances, stop and back up. Drive on to
the next exit.
The exit ramp can be curved, sometimes quite sharply.

4-39 Making Turns
NOTICE:
Making very sharp turns while trailering could
cause the trailer to come in contact with the
vehicle. Your vehicle could be damaged. Avoid
making very sharp turns while trailering.
When you're turning with a trailer, make wider
turns than normal. Do this so your trailer won't
strike soft shoulders, curbs, road signs, trees or other
objects. Avoid jerky or sudden maneuvers. Signal well
in advance.
Turn Signals When Towing a Trailer
When you tow a trailer, your vehicle may need a
different turn signal flasher and/or extra wiring. Check
with your dealer. The arrows on your instrument panel
will flash whenever you signal a turn or lane change.
Properly hooked up, the trailer lamps will also flash,
telling other drivers you're about to turn, change lanes
or stop.
When towing a trailer, the arrows on your instrument
panel will flash for turns even if the bulbs on the trailer
are burned out. Thus, you may think drivers behind you
are seeing your signal when they are not. It's important
to check occasionally to be sure the trailer bulbs are
still working.
Driving On Grades
Reduce speed and shift to a lower gear before you start
down a long or steep downgrade. If you don't shift
down, you might have to use your brakes so much that
they would get hot and no longer work well.
On a long uphill grade, shift down and reduce your
speed to around 45 mph (70 km/h) to reduce the
possibility of the engine and the transmission
overheating.

5-2
Hazard Warning Flashers
Your hazard warning flashers let you warn others. They
also let police know you have a problem. Your front and
rear turn signal lamps will flash on and off.
The hazard warning button
is located in the center of
the instrument panel,
between the two air vents.
Your hazard warning flashers work no matter what
position your key is in, and even if the key isn't in.
Press the button to make the front and rear turn signal
lamps flash on and off. The light in the center of the
button will flash, indicating that the hazard warning
flashers are on. Press the button again to turn the
flashers off.
When the hazard warning flashers are on, neither your
turn signals nor your Daytime Running Lamps (DRL)
will work.

6-36 Front Turn Signal and Fog Lamps
A. Turn Signal Lamp
B. Fog Lamp
To replace the front turn signal or fog lamps, use the
following procedure:
1. Remove the protection shield located on the
underside of the front of the vehicle by pulling out
the push
-pins located on the underside of the
protection shield.2. Reach up behind the front bumper area from under
the vehicle to access the lamp housing.
3. Remove the bulb socket from the housing by turning
the bulb socket one
-quarter turn counterclockwise.
4. Remove the electrical connector from the bulb by
lifting the two plastic clips.
5. Pull the old bulb from the bulb socket keeping the
bulb straight as you pull it out.
6. Install a new bulb.
7. Reverse the steps to reinstall the lamp assembly.
Center High-Mounted Stop
Lamp (CHMSL)
It is recommended that this component be replaced as a
unit. See your dealer.

6-37 Rear Tail/Stop/Turn Signal and
Side-Marker Lamps
A. Tail and Stop Lamps
B. Turn Signal Lamp
C. Side
-Marker Lamp
To replace the tail, stop, turn signal or side
-marker
lamps use the following procedure:
1. Open the trunk using the trunk button on the remote
keyless entry transmitter or the trunk release button
located on the lower part of the driver's door.2. Remove the compact spare tire cover by turning the
wing nut counterclockwise.
3. Remove the four convenience net wing nuts.
4. Pull the carpet back away from the body of the
vehicle on the side with the burned out bulb.
5. Remove the two mounting screws from the
lamp assembly.
6. Pull out the lamp assembly to expose the
bulb sockets.
7. Turn the bulb socket one
-quarter turn
counterclockwise and pull the bulb and socket out
of the lamp reflector.
8. Pull the old bulb from the bulb socket keeping the
bulb straight as you pull it out.
9. Install a new bulb.
10. Reverse the steps to reinstall the lamp assembly.

6-63
Mini Fuses Usage
LT HI BEAM Driver's Side High
-Beam
Headlamp
LT LOW BEAM Driver's Side Low
-Beam
Headlamp
RT LOW BEAM Passenger's Side Low
-Beam
Headlamp
RT HI BEAM Passenger's Side High
-Beam
Headlamp
SPARE Not Used
SPARE Not Used
THEFT ECM (Electronic Control
Module), TCM (Transmission
Control Module), PASS
-Key III+
Module
LT PARK Driver's Side Taillamp Assembly,
Front Sidemarker and Front
Parking Lamp Assembly
LIC/DIMMING Rear License Plate
Assembly, DIMMini Fuses Usage
DIM/ALDL DIM, ALDL (Assembly Line
Data Link)
FLASHER Turn Signal/Hazard Flasher
Module
MANIFOLD Manifold Flaps 1 and 2, Air Mass
Meter, Canister Purge Valve
STRG CTLS Steering Wheel Control Pad,
Headlamp Switch
HTR
VLV/CLTCHHeater Valve, Clutch Switch
(Normal Closed), Clutch Switch
(Normal Open), Jumper to Start
Relay Coil for Automatic
Transmission
WASH NOZ Driver's and Passenger's Side
Heated Washer Nozzles
ECM Electronic Control Module
TCM/IPC TCM, ECM and IPC
(Instrument Panel Cluster)
SPARE Not Used
IGN MOD Front Bank Ignition Modules

6-72
Replacement Bulbs
For any bulb not listed here contact your dealer.
Application Number
Front and Rear Turn Signal Lamps 3157K. . . . . . . . .
Fog Lamps 9145. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back
-Up Lamps 3157K. . . . . . . . . . . . . . . . . . . . . . . .
License Plate Lamps W5WLL. . . . . . . . . . . . . . . . . .
Taillamps 3157K. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stop Lamps 3157K. . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Sidemarker Lamps 3157K. . . . . . . . . . . . . . . . . .
Capacities and Specifications
The following approximate capacities are given in
English and metric conversions. Please refer to
ªRecommended Fluids and Lubricantsº Index
for more information.
Engine Specifications
Type 3.2 L V6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VIN Engine Code N. . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel Nut Torque
100 lb-ft (140 N´m)
Capacities
Automatic
Transmission (5L40
-E) 9.0 quarts (8.5 L). . . . . . . .
Manual Transmission (M35) 1.3 quarts (1.3 L). . . . .
Engine Oil with Filter 5.0 quarts (4.8 L). . . . . . . . . .
Engine Cooling System 10.4 quarts (9.8 L). . . . . . . .
Fuel Tank 17.5 U.S. gallons (66.2 L). . . . . . . . . . . . .
All capacities are approximate. When adding, be sure to
fill to the approximate level, as recommended in this
manual. Recheck fluid level after filling.