buttons CADILLAC CTS 2003 1.G Owners Manual
[x] Cancel search | Manufacturer: CADILLAC, Model Year: 2003, Model line: CTS, Model: CADILLAC CTS 2003 1.GPages: 435, PDF Size: 2.71 MB
Page 9 of 435
1-3 Memory Seat and Mirrors (If Equipped)
This feature allows you to program and recall memory
settings for the driver's seating and outside rearview
mirror driving positions for up to two drivers.
The buttons for this feature
are located on the driver's
door armrest.
Use the following steps to program the buttons:
1. Adjust the driver's seat including the seatback
recliner and both outside mirrors.
2. Press and hold button 1 for at least three seconds.
Two beeps will sound to confirm that the seat and
mirror positions have been saved.
3. Repeat the procedure for a second driver
using button 2.If your vehicle has an automatic transmission, the
vehicle must be in PARK (P) to recall the stored driving
positions. If your vehicle has a manual transmission and
the engine is running, the parking brake must be set to
recall the memory seat driving positions. The stored
driving positions can be recalled without setting the
parking brake if the vehicle is off.
Press one of the numbered memory buttons to recall the
stored setting. Each time a memory button is pressed, a
single beep will sound.
Three chimes will sound and the setting will not be
recalled if you press button 1 or 2 while the engine is
running and the vehicle is not in PARK (P) on an
automatic transmission or the parking brake is not
set on a manual transmission.
If you would like the stored driving positions to be
recalled when unlocking your vehicle with the remote
keyless entry transmitter or when you place the key in
the ignition, see ªVehicle Programming and
Personalization Featuresº in the Index.
To stop recall movement of the memory feature at any
time, press one of the power seat or mirror controls.
Page 10 of 435
1-4
Two personalized exit positions can also be
programmed. Use the following steps to program
exit positions:
1. Press memory seat button 1 or the button with
the unlock symbol on the remote keyless entry
transmitter with the number 1 on the back to recall
the drive position.
2. Adjust the driver's seat to the desired exit position.
3. Press and hold the exit button located above
buttons 1 and 2 on the driver's door armrest for
at least three seconds.
Two beeps will sound to confirm that the exit
position has been saved.
4. Repeat the procedure for a second driver using
memory seat button 2 or the remote keyless entry
transmitter with the number 2 on the back.To recall the stored exit positions, press and release the
exit button. One beep will sound, and the seat will move
to the previously stored exit position for the currently
identified driver. If an exit position has not been stored
for this driver, the seat will move all the way back. The
position of the outside mirrors is not stored or recalled
for the exit position.
If your vehicle has an automatic transmission, the
vehicle must be in PARK (P) to recall the exit positions.
For a manual transmission, the parking brake must
be set if the engine is running to recall the stored
exit positions.
Three chimes will sound and the exit setting will not be
recalled if you press the exit button while the engine is
running and the vehicle is not in PARK (P) on an
automatic transmission or the parking brake is not set on
a manual transmission.
If you would like your stored exit position to be recalled
when unlocking the vehicle with the remote keyless
entry transmitter or when the ignition is turned off and
the driver's door is opened, see ªVehicle Programming
and Personalization Featuresº in the Index.
Page 11 of 435
1-5 Heated Front Seats (If Equipped)
If your vehicle is equipped
with heated front seats, the
buttons are located on the
climate control panel.There is a button for the driver and one for the front
passenger. Each button has the following three settings:
LO, HI and off. The active setting appears on the
climate control panel display. The LO setting warms the
seatback and cushion until the seat approximates normal
body temperature. The HI setting has a slightly higher
temperature.
To turn on the heated seats, press the button once. The
seat will heat to the HI setting. Press the button again to
switch to the LO setting. Pressing the button a third time
turns the system off.
The heated seats can only be used when the ignition is
turned on. When the vehicle is turned off, the heated
seats automatically turn off. If you wish to have the
heated seats on once the vehicle is restarted, press the
button again.
Page 83 of 435
2-15
2. Scroll through the menu by turning the knob.
3. When SETUP appears on the display, press the knob
once to select it.
4. Scroll through the SETUP menu by turning
the knob.
5. When CONFIGURE SWC KEYS appears on the
display, press the knob once to select it.
6. Scroll through the buttons (1, 2, 3 or 4). When you
reach the control you wish to program, press the
knob once to select it.
7. Choose a new function for the control by scrolling
through the list of available functions.
8. Once you've highlighted your choice, press the knob
once to select it.
The control you selected is now programmed with
the function you selected.
9. Press the BACK button to exit each menu.
If you desire to program another control, repeat
the procedure.
If your vehicle is equipped with the Navigation system,
do the following:
1. Press the MAIN button located to the lower left of
the display.2. Press the multi-function button next to the Setup
prompt at the right of the display.
3. Turn the TUNE/SEL knob located to the lower right
of the display to scroll through the Setup menu.
4. When Program SWC appears on the display, press
the knob once to select it.
5. Turn the knob to scroll through the available
functions.
6. Once the function desired is highlighted, press and
hold the multi
-function button next to the control
you wish to program (1, 2, 3 or 4). The buttons are
located at the right of the display.
When a control is successfully programmed, the
function you selected will appear next to the number
of the control at the right of the display.
7. Press the multi
-function button next to the Back
prompt to exit each menu. If you desire to program
another control, repeat the procedure.
Each function can only be used once. When you
program a control with a function, that function is
removed from the list of functions available. It will
return to the list if you remove it from the SWC it is
programmed to by programming another function to
that control.
Page 121 of 435
2-53
Cruise Control
: On/Off
+: Resume/Accelerate, Set
-: Coast/Decelerate, Set
The buttons used to operate cruise control are located at
the bottom of the steering wheel.
With cruise control, you can maintain a speed of
approximately 25 mph (40 km/h) or more without
keeping your foot on the accelerator. This is helpful on
long trips. Cruise control does not work at speeds below
about 25 mph (40 km/h).When you apply your brakes, the cruise control
shuts off.
CAUTION:
Cruise control can be dangerous where you
can't drive safely at a steady speed. So,
don't use your cruise control on winding
roads or in heavy traffic.
Cruise control can be dangerous on
slippery roads. On such roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control. Don't
use cruise control on slippery roads.
If your vehicle is in cruise control when the traction
control system begins to limit wheel spin, the cruise
control will automatically disengage. See ªTraction
Control Systemº and ªStabilitrak Systemº in the Index.
When road conditions allow you to safely use it again,
you may turn the cruise control back on.
Page 123 of 435
2-55
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:
Use the accelerator pedal to get to the higher speed.
Press either the plus or minus button, then release the
button and the accelerator pedal. You will now cruise
at the higher speed.
Press the resume/accelerate button. Hold it there
until you get up to the speed that you want, and then
release the button. To increase your speed in very
small amounts, briefly press the resume/accelerate
button and then release it. Each time you do
this, your vehicle will speed up approximately
1 mph (1.6 km/h).
The accelerate feature will only work after you have
set the cruise control speed by pressing one of the
set buttons.Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:
Press the coast/decelerate button until you reach the
lower speed you want, then release it.
To slow down in very small amounts, push the
coast/decelerate button briefly. Each time you
do this, the vehicle will slow down approximately
1 mph (1.6 km/h).
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.
Page 135 of 435
2-67
Cigarette Lighter
NOTICE:
Don't hold a cigarette lighter in with your hand
while it is heating. If you do, it won't be able to
back away from the heating element when it's
ready. That can make it overheat, damaging the
lighter and the heating element.
The cigarette lighter is located next to the ashtray. The
vehicle does not have any cigarette lighters for the rear
seat passengers.
Press the lighter all the way in and release it. It will pop
back out by itself once the element has heated for use.
Cigarette lighters can be used to provide power to
accessories. See ªAccessory Power Outletsº in the
Index for more information.
Sun Visors
Swing down the primary visor to block out glare. It can
also be detached from the center mount and moved to
the side to block glare from that direction.
The driver's sunshade may also have buttons for a
built
-in garage door opener and a recording device. See
ªHomeLink Transmitterº and ªTravel Note Recorderº
later in this section for more information.
Lighted Visor Vanity Mirror
Pull the visor down and lift the cover. The light will
automatically come on. The light will go out when you
close the cover.
Page 138 of 435
2-70
OnStar System (If Equipped)
OnStar is a vehicle communications system that offers a
variety of services and provides a one
-touch hands-free
communication link between you and the OnStar Center.
To receive OnStar services, a service subscription
agreement is required and an additional fee may be
required. Services are available 24 hours a day, 7 days a
week. For more information, call 1
-888-ONSTAR-7
(1
-888-667-8277).
OnStar Services Button: Press this button once to
contact an advisor who will be able to assist you with
these services. If you are not quickly connected, the
system will automatically reset and redial. This ensures
connection to the center; there is no additional action
required. Press the Communication button to cancel the
automatic redial.
Emergency Button: In an emergency situation,
press the emergency service button. Upon receiving the
call, an advisor at the center will locate your vehicle and
assess the situation. If necessary, the advisor will alert
the nearest emergency service provider.
Communication Button: Press this button at
the end of a call. Also press this button to answer a
call from the center, or cancel a call if one of the other
buttons is accidentally pressed. This button is also used
to access OnStar Personal Calling and Virtual Advisor
services. See the OnStar owner package for more
information.
Volume Control: You can control the volume of the
OnStar System using the steering wheel controls.
Page 143 of 435
2-75
HomeLink Transmitter
(If Equipped)
A. HomeLink
Transmitter
Buttons
B. Travel Note
Recorder Buttons
(If Equipped)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
This device complies with RSS
-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference, including interference
that may cause undesired operation of the device.Changes and modifications to this system by other than
an authorized service facility could void authorization to
use this equipment.
Programming the HomeLink Transmitter
Do not use the HomeLink Transmitter with any garage
door opener that does not have the ªstop and reverseº
feature. This includes any garage door opener model
manufactured before April 1, 1982.
Be sure that people and objects are clear of the garage
door you are programming.
It is recommended that a new battery be installed in
your hand
-held transmitter for quicker and more
accurate transmission of the radio frequency.
Your vehicle's engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. Decide which one of the three channels (one of the
HomeLink buttons) you want to program.
2. Press and hold the desired button on HomeLink
through Step 3.
Page 144 of 435
2-76
3. When the HomeLink indicator light begins to blink
slowly (this may take up to 30 seconds), hold the
hand
-held transmitter about 1 to 3 inches (3 to 8 cm)
away from HomeLink and then press and hold the
transmit button on the hand
-held transmitter.
Continue to hold both buttons until the indicator
light on HomeLink begins to flash rapidly (this may
take up to 90 seconds).
If you have trouble programming HomeLink, make sure
that you have followed the directions exactly as
described and that the battery in the hand
-held
transmitter is not weak. If you still cannot program it,
move the hand
-held transmitter to the left or right or
forward or backward or flip it upside down. HomeLink
may not work with older garage door openers that do
not meet current Federal Consumer Safety Standards.
If you cannot program the transmitter after repeated
attempts, refer to ªTraining a Garage Door Opener with
a `Rolling Code' Featureº next in this section or contact
the manufacturer of HomeLink at 1
-800-355-3515, or
on the internet at www.homelink.com.
Be sure to keep the original hand
-held transmitter in
case you need to erase and reprogram HomeLink.
Training a Garage Door Opener with a
ªRolling Codeº Feature (If Equipped)
If you have not previously programmed the hand-held
transmitter to HomeLink, see ªProgramming the
HomeLink Transmitterº listed previously. If you have
completed this programming already, you now need to
train the garage door opener motor head unit to
recognize HomeLink.
1. Find the ªLearnº or ªSmartº button on the garage
door opener motor head unit. The exact location and
color will vary by garage door opener brand. If you
have difficulty finding the Learn or Smart button,
refer to your garage door opener owner's manual or
contact the manufacturer of HomeLink at
1
-800-355-3515, or on the internet at
www.homelink.com.
Because of the steps involved, it may be helpful to
have another person assist in programming the
transmitter.