mirror CADILLAC CTS 2003 1.G Owners Manual

1-3 Memory Seat and Mirrors (If Equipped)
This feature allows you to program and recall memory
settings for the driver's seating and outside rearview
mirror driving positions for up to two drivers.
The buttons for this feature
are located on the driver's
door armrest.
Use the following steps to program the buttons:
1. Adjust the driver's seat including the seatback
recliner and both outside mirrors.
2. Press and hold button 1 for at least three seconds.
Two beeps will sound to confirm that the seat and
mirror positions have been saved.
3. Repeat the procedure for a second driver
using button 2.If your vehicle has an automatic transmission, the
vehicle must be in PARK (P) to recall the stored driving
positions. If your vehicle has a manual transmission and
the engine is running, the parking brake must be set to
recall the memory seat driving positions. The stored
driving positions can be recalled without setting the
parking brake if the vehicle is off.
Press one of the numbered memory buttons to recall the
stored setting. Each time a memory button is pressed, a
single beep will sound.
Three chimes will sound and the setting will not be
recalled if you press button 1 or 2 while the engine is
running and the vehicle is not in PARK (P) on an
automatic transmission or the parking brake is not
set on a manual transmission.
If you would like the stored driving positions to be
recalled when unlocking your vehicle with the remote
keyless entry transmitter or when you place the key in
the ignition, see ªVehicle Programming and
Personalization Featuresº in the Index.
To stop recall movement of the memory feature at any
time, press one of the power seat or mirror controls.

1-4
Two personalized exit positions can also be
programmed. Use the following steps to program
exit positions:
1. Press memory seat button 1 or the button with
the unlock symbol on the remote keyless entry
transmitter with the number 1 on the back to recall
the drive position.
2. Adjust the driver's seat to the desired exit position.
3. Press and hold the exit button located above
buttons 1 and 2 on the driver's door armrest for
at least three seconds.
Two beeps will sound to confirm that the exit
position has been saved.
4. Repeat the procedure for a second driver using
memory seat button 2 or the remote keyless entry
transmitter with the number 2 on the back.To recall the stored exit positions, press and release the
exit button. One beep will sound, and the seat will move
to the previously stored exit position for the currently
identified driver. If an exit position has not been stored
for this driver, the seat will move all the way back. The
position of the outside mirrors is not stored or recalled
for the exit position.
If your vehicle has an automatic transmission, the
vehicle must be in PARK (P) to recall the exit positions.
For a manual transmission, the parking brake must
be set if the engine is running to recall the stored
exit positions.
Three chimes will sound and the exit setting will not be
recalled if you press the exit button while the engine is
running and the vehicle is not in PARK (P) on an
automatic transmission or the parking brake is not set on
a manual transmission.
If you would like your stored exit position to be recalled
when unlocking the vehicle with the remote keyless
entry transmitter or when the ignition is turned off and
the driver's door is opened, see ªVehicle Programming
and Personalization Featuresº in the Index.

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Windows
2
-5 Keys
2
-7 Door Locks
2
-10 Remote Keyless Entry System
2
-16 Trunk Lid
2
-19 Theft
2
-21 Immobilizer
2
-24 New Vehicle ªBreak-Inº
2
-24 Ignition Positions
2
-27 Starting Your Engine
2
-28 Engine Coolant Heater (If Equipped)
2
-30 Automatic Transmission Operation
2
-37 Manual Transmission Operation
2
-38 Parking Brake
2
-40 Shifting Into PARK (P)
(Automatic Transmission Only)
2
-42 Shifting Out of PARK (P)
(Automatic Transmission Only)
2
-42 Parking Your Vehicle
(Manual Transmission Only)2
-43 Parking Over Things That Burn
2
-44 Engine Exhaust
2
-44 Running Your Engine While You're Parked
(Automatic Transmission)
2
-46 Turn Signal/Multifunction Lever
2
-56 Exterior Lamps
2
-59 Interior Lamps
2
-60 Mirrors
2
-70 OnStar
System (If Equipped)
2
-74 Sunroof (Option)
2
-75 HomeLink
Transmitter (If Equipped)
2
-80 The Instrument Panel -- Your
Information System
2
-85 Warning Lights, Gages and Indicators
2
-99 Driver Information Center (DIC)
2
-130 Vehicle Programming and
Personalization Features
2
-153 Navigation (Option)

2-12
(Unlock): When you press this symbol on the
remote keyless entry transmitter, the driver's door will
unlock. This also disarms the theft
-deterrent system.
Press the button again to unlock the rest of the doors.
You can program your vehicle so that the exterior lamps
will flash when you unlock the doors with the remote
keyless entry transmitter. See ªVehicle Programming
and Personalization Featuresº in the Index for more
information on programming this feature.
If your vehicle is programmed for remote confirmation,
the doors must be closed for this feature to work. If a
door is open, remote confirmation will be canceled.
(Panic Alarm): The remote keyless entry
transmitter comes equipped with an instant panic alarm.
To use the alarm, press the horn symbol when the
ignition is turned off. The horn will sound and the
exterior lamps will flash for up to 30 seconds. To stop
the instant panic alarm, press the symbol again or turn
the ignition to ON.
(Trunk): Press this button to open the trunk.
The remote keyless entry transmitter can be used to
recall the memory settings for up to two drivers. For
more information, see ªVehicle Programming and
Personalization Featuresº and ªMemory Seat and
Mirrorsº in the Index.
Matching Transmitter(s) to Your Vehicle
Each remote keyless entry transmitter is coded to
prevent another transmitter from unlocking your vehicle.
If a transmitter is lost or stolen, a replacement can be
purchased through your dealer. Remember to bring any
remaining transmitters with you when you go to your
dealer. When the dealer matches the replacement
transmitter to your vehicle, any remaining transmitters
must also be matched. Once your dealer has coded the
new transmitter, the lost transmitter will not unlock your
vehicle. Each vehicle can have a maximum of four
transmitters matched to it.

2-60
Reading Lamps
The reading lamps are located on the overhead console.
These lamps come on automatically when any door
is opened.
For manual operation, press the button next to each
lamp to turn them on. Press it again to turn them off.
If the reading lamps are left on, they automatically shut
off 10 minutes after the ignition has been turned off.
Mirrors
Electrochromic Day/Night Rearview Mirror
with OnStar
System
Your vehicle has an electrochromic inside rearview
mirror. The mirror also contains OnStar controls.
For more information about OnStar, see ªOnStarº in
the Index.
(On/Off): This is the on/off button, located on the
lower left side of the mirror for the electrochromic
functions of the rearview mirror.Mirror Operation
The automatic dimming feature is active each time the
vehicle is started.
To turn the automatic dimming feature on or off, press
and hold the on/off button for about three seconds. The
indicator light will illuminate when this feature is active.
Cleaning the Mirror
When cleaning the mirror, use a paper towel or similar
material dampened with glass cleaner. Do not spray
glass cleaner directly on the mirror as that may cause the
liquid cleaner to enter the mirror housing.

2-61
Electrochromic Day/Night Rearview
Mirror with Compass and OnStar
System
(If Equipped)
Your vehicle may have an electrochromic inside
rearview mirror with a compass. The mirror also
contains OnStar controls. For more information about
OnStar, see ªOnStarº in the Index.
The mirror has an eight
-point compass display in the
upper right corner of the mirror face. When on, the
compass automatically calibrates as the vehicle is
driven.
(On/Off): This is the on/off button, located on the
lower left side of the mirror for the electrochromic
functions of the rearview mirror.
Mirror Operation
The electrochromic feature on the mirror functions
exactly the same as the base electrochromic mirror.
See ªElectrochromic Day/Night Rearview Mirror with
OnStar

Systemº listed previously in this section for
more information.Compass Operation
Press the on/off button once to turn the compass on
or off.
When the ignition and the compass feature are on,
the compass will show two character boxes for
approximately two seconds. After two seconds, the
mirror will display the current compass heading.
Compass Calibration
If after two seconds the display does not show a
compass heading (N for North for example), there may
be a strong magnetic field interfering with the compass.
Such interference may be caused by a magnetic antenna
mount, note pad holder or similar object. If the letter C
should ever appear in the compass window, the compass
may need calibration.
The mirror can be calibrated by driving the vehicle in
circles at 5 mph (8 km/h) or less until the display reads
a direction.
The compass can be placed in calibration mode by
pressing and holding the on/off button until a C is
shown in the compass display.

2-62
Compass Variance
Compass variance is the difference between earth's
magnetic north and true geographic north. If the mirror
is not adjusted for compass variance, your compass
could give false readings.
The mirror is set in zone eight upon leaving the factory.
It will be necessary to adjust the compass to compensate
for compass variance if you live outside zone eight.
Under certain circumstances, such as a long distance,
cross
-country trip, it will be necessary to adjust the
compass variance.
To adjust for compass variance, do the following:
1. Find your current location and variance zone number
on the zone map that follows.
2. Press and hold the on/off button until a zone number
appears on the display.
3. Once the zone number appears on the display, press
the on/off button quickly until you reach the correct
zone number. Stop pressing the button and the mirror
will return to normal operation. If C appears in the
compass window, the compass may need calibration.
See ªCompass Calibrationº listed previously.

2-63
Cleaning the Mirror
When cleaning the mirror, use a paper towel or similar
material dampened with glass cleaner. Do not spray
glass cleaner directly on the mirror as that may cause the
liquid cleaner to enter the mirror housing.
Power Outside Rearview Mirrors
The control on the driver's door armrest operates both
outside rearview mirrors.Press the left mirror symbol on the selector switch to
choose the driver's side mirror or the right mirror
symbol to choose the passenger's side mirror. The center
position is off and will not move the mirrors if the
control pad is touched.
Once you select the mirror you want to adjust, use the
arrows on the control pad to move the mirror in the
direction you want the mirror to go. Adjust each mirror
so you can see the side of your vehicle and the area
behind your vehicle.
The mirrors can be manually folded inward to prevent
damage when going through an automatic car wash. To
fold, push the mirror toward the vehicle. To return the
mirror to its original position, push outward. Be sure to
return both mirrors to their original unfolded position
before driving.
The mirrors can also be programmed for personalization
and the curb view assist feature if you have the optional
memory package. For more information, see ªMemory
Seat and Mirrorsº and ªVehicle Programming and
Personalization Featuresº in the Index.

2-64
Curb View Assist Mirror (If Equipped)
If your vehicle is equipped with the memory seat and
mirrors, it will also be capable of performing the curb
view assist mirror feature. This feature will cause the
passenger's mirror to tilt to a preselected position when
the vehicle is shifted into REVERSE (R). Use this
feature to view the curb when you are parallel parking.
When the vehicle is shifted out of REVERSE (R) and a
five
-second delay has occurred, the passenger's mirror
will return to its original position.
If further adjustment is needed after the mirror is
tilted, the mirror controls can be used. See ªPower
Outside Rearview Mirrorsº listed previously for
more information.
This feature can be enabled/disabled through the DIC.
See ªVehicle Programming and Personalization
Featuresº in the Index for more information.
Convex Outside Mirror
Your passenger's side mirror is convex. A convex
mirror's surface is curved so you can see more from the
driver's seat.
CAUTION:
A convex mirror can make things (like other
vehicles) look farther away than they really are.
If you cut too sharply into the right lane, you
could hit a vehicle on your right. Check your
inside mirror or glance over your shoulder before
changing lanes.
Heated Outside Rearview Mirrors
When you operate the rear window defogger, it also
warms both outside rearview mirrors to help clear them
of fog or ice. See ªRear Window Defoggerº in the Index
for more information.

2-67
Cigarette Lighter
NOTICE:
Don't hold a cigarette lighter in with your hand
while it is heating. If you do, it won't be able to
back away from the heating element when it's
ready. That can make it overheat, damaging the
lighter and the heating element.
The cigarette lighter is located next to the ashtray. The
vehicle does not have any cigarette lighters for the rear
seat passengers.
Press the lighter all the way in and release it. It will pop
back out by itself once the element has heated for use.
Cigarette lighters can be used to provide power to
accessories. See ªAccessory Power Outletsº in the
Index for more information.
Sun Visors
Swing down the primary visor to block out glare. It can
also be detached from the center mount and moved to
the side to block glare from that direction.
The driver's sunshade may also have buttons for a
built
-in garage door opener and a recording device. See
ªHomeLink
Transmitterº and ªTravel Note Recorderº
later in this section for more information.
Lighted Visor Vanity Mirror
Pull the visor down and lift the cover. The light will
automatically come on. The light will go out when you
close the cover.