warning CADILLAC DEVILLE 1999 7.G User Guide

yellowblue
2-71 Anti-Lock Brake System Warning Light
Digital Cluster Analog Cluster
With the anti
-lock brake system, the light(s) will come
on when you start your engine and may stay on for
several seconds. That's normal.If the light stays on, turn the ignition to OFF. Or, if the
light comes on when you're driving, stop as soon as
possible and turn the ignition off. Then start the engine
again to reset the system. If the light still stays on, or
comes on again while you're driving, your vehicle needs
service. If the regular brake system warning light isn't
on, you still have brakes, but you don't have anti
-lock
brakes. If the regular brake system warning light is also
on, you don't have anti
-lock brakes and there's a
problem with your regular brakes. See ªBrake System
Warning Lightº earlier in this section.
The anti
-lock brake system warning light should come
on briefly when you turn the ignition key to RUN. If the
light doesn't come on then, have it fixed so it will be
ready to warn you if there is a problem.

yellowblue
2-72 Traction Control System Warning Light
This warning light should
come on briefly as you start
the engine. If the warning
light doesn't come on then,
have it fixed so it will be
ready to warn you if there's
a problem.
If it stays on, or comes on when you're driving, there
may be a problem with your traction control system and
your vehicle may need service. When this warning light
is on, the system will not limit wheel spin. Adjust your
driving accordingly.
The traction control system warning light may come on
for the following reasons:

If there's a brake system problem that is specifically
related to traction control, the traction control system
will turn off and the warning light will come on.

If the traction control system is affected by an
engine
-related problem, the system will turn off and
the warning light will come on.If the traction control system warning light comes on
and stays on for an extended period of time when the
system is turned on, your vehicle needs service.
Engine Coolant Temperature
Warning Light
This light tells you that your
engine has overheated. You
should stop your vehicle
and turn the engine off as
soon as possible. A warning
chime should also sound if
this light comes on.
As a check, the light should come on for a few seconds
when you start your engine. See ªEngine Overheatingº
in the Index.

yellowblue
2-73 Engine Coolant Temperature Gage
This gage shows the engine
coolant temperature. If
the gage pointer moves into
the red area, the engine is
too hot.
Analog Cluster
That reading means the same thing as the warning
light
-- the engine coolant has overheated. See
ªEngine Overheatingº in the Index.
Malfunction Indicator Lamp
(Service Engine Soon Light)
Your vehicle is equipped
with a computer which
monitors operation of the
fuel, ignition and emission
control systems.
This system is called OBD II (On
-Board
Diagnostics
-Second Generation) and is intended to
assure that emissions are at acceptable levels for the life
of the vehicle, helping to produce a cleaner
environment. The SERVICE ENGINE SOON light
comes on and a chime will sound to indicate that there is
a problem and service is required. Malfunctions often
will be indicated by the system before any problem is
apparent. This may prevent more serious damage to
your vehicle. This system is also designed to assist
your service technician in correctly diagnosing
any malfunction.

yellowblue
2-79
Driver Information Center (DIC)
This display gives you the status of many of your
vehicle's systems. The DIC is also used to display driver
personalization features and warning/status messages.
DIC Controls and Displays
Digital Control Buttons (DeVille and DeVille
d'Elegance Only)
DISPLAY ON/OFF: Pressing this button will turn off
the DIC, Electronic Climate Control (ECC), fuel data
center, the fuel gage, trip odometer and odometer. While
the displays are off, pressing the INFORMATION SKIP
button will only turn on the DIC. If the TRIP YES
button is pressed or the fuel level falls below four
gallons (15.2 L), all of the displays will come back on.
ENG/MET: You can change the display from English
(miles) to metric (kilometers) by pressing this button.
The same button also changes other readings (like
temperature, fuel and odometer).
TRIP YES: By using this button, you can tell how far
you've gone since you last set the trip display back to
zero. To reset, press and hold the button until zeros
appear. If your vehicle is domestic, the trip odometer
will return to zero after 999.9 miles (1 609 km). If your
vehicle is Canadian, the trip odometer will return to zero
after 1 999.9 km (1,242 miles).
INFORMATION SKIP: Pressing this button
repeatedly will display the MPG AVG, GAL FUEL
USED, AVG MPH, ENGINE RPM, BATTERY
VOLTS, COOLANT TEMP and OIL LIFE LEFT.

yellowblue
2-80
TIMER: This feature is like a stopwatch, in that
you can clock the time it takes to get from one point
to another.
To operate, press the TIMER button until TIMER OFF
00:00:00 is displayed on the DIC. Each of the fields for
the hours, minutes and seconds are two numeric digits.
Once TIMER OFF 00:00:00 is displayed, press the
TIMER button to start the timing feature. Press the
TIMER button again to stop it. If you will be starting and
stopping your vehicle
-- during a trip for instance -- the
TIMER feature will automatically start timing where it left
off when you last stopped. To reset it, press and hold the
RESET NO button until the display reads TIMER
00:00:00. Press the INFORMATION SKIP button to
exit from the TIMER function.
RESET NO: Pressing this button will reset the MPG
AVG, GAL FUEL USED, AVG MPH and OIL LIFE
LEFT. Pressing RESET NO when a non
-resettable
display appears will cause a ªrecallº mode to occur.
When this happens, all DIC warning messages that have
been displayed since the ignition key was turned to
RUN will redisplay. If no messages were displayed, a
MONITORED SYSTEMS OK message will appear.MPG AVG (Reset): Press the INFORMATION SKIP
button to display the MPG AVG (Average Fuel
Economy), then press and hold the RESET NO
button until 0.0 MPG AVG is displayed.
GAL FUEL USED (Reset): Press the INFORMATION
SKIP button to display the GAL FUEL USED on the
DIC, then press and hold the RESET NO button
until 0.0 GAL FUEL USED is displayed.
AVG MPH (Reset): Press the INFORMATION
SKIP button to display the AVG MPH (Average Speed),
then press and hold the RESET NO button until
0.0 AVG MPH is displayed.
OIL LIFE LEFT (Reset): Press the INFORMATION
SKIP button to display the OIL LIFE LEFT, then press
and hold the RESET NO button until 100% OIL LIFE
LEFT is displayed. (This only needs to be reset after you
have had the oil changed.)

yellowblue
2-81
Analog Control Buttons (DeVille Concours Only)
YES TRIP RESET: By using this button, you can tell
how far you've gone since you last set the trip display
back to zero. To reset, press and hold the button until
zeros appear. If your vehicle is domestic, the trip
odometer will return to zero after 999.9 miles
(1 609 km). If your vehicle is Canadian, the trip
odometer will return to zero after 1 999.9 km
(1,242 miles).
NO INFO RESET: Pressing this button will reset the
MPG AVG, GAL FUEL USED, AVG MPH and OIL
LIFE LEFT. Pressing NO INFO RESET when a
non
-resettable display appears will cause a ªrecallº
mode to occur. When this happens, all DIC warning
messages that have been displayed since the ignition key
was turned to RUN will redisplay. If no messages were
displayed, a MONITORED SYSTEMS OK message
will appear.SKIP INFO: Pressing this button repeatedly will
display the RANGE, MPG AVG, MPG INST, GAL
FUEL USED, AVG MPH, BATTERY VOLTS and
OIL LIFE LEFT.
TIMER: This feature is like a stopwatch, in that
you can clock the time it takes to get from one point
to another.
To operate, press the TIMER button until TIMER OFF
00:00:00 is displayed on the DIC. Each of the fields for
the hours, minutes and seconds are two numeric digits.
Once TIMER OFF 00:00:00 is displayed, press the
TIMER button to start the timing feature. Press the
TIMER button again to stop it. If you will be starting
and stopping your vehicle
-- during a trip for
instance
-- the TIMER feature will automatically start
timing where it left off when you last stopped. To reset
it, press and hold the NO INFO RESET button until the
display reads TIMER 00:00:00. Press the NO INFO
RESET button to exit from the TIMER function.
ENG/MET: You can change the display from English
(miles) to metric (kilometers) by pressing this button.
The same button also changes other readings (like
temperature, fuel and odometer).

yellowblue
2-84
CHANGE TRANS FLUID - 47: This message will
appear when it is time to replace the transaxle fluid. See
the Maintenance Schedule booklet for the proper fluid
and change intervals.
CHECK BRAKE FLUID
- 37: This message will
display if the ignition is in RUN to inform the driver that
the brake fluid level is low. Check the brake reservoir
level and add fluid as needed. Have the brake system
serviced by a technician as soon as possible. If the brake
warning light is on, follow the directions in that part.
CHECK COOLANT LEVEL
- 2: This message
will appear when there is a low level of engine coolant.
Have the cooling system serviced by a technician as
soon as possible.
CHECK FUEL GAUGE
- 39: This message will
appear when the fuel supply is less than four gallons
(15.2 L) and the display is turned off (digital clusters
only). A single chime will also sound when this message
is displayed.
CHECK GAS CAP
- 61: This message will appear if
the gas cap has not been fully tightened. You should
recheck your gas cap to ensure that it's fully tightened.CHECK OIL LEVEL
- 36: For correct operation of
the low oil sensing system, your vehicle should be on a
level surface. A false CHECK OIL LEVEL message
may appear if the vehicle is parked on grades. The oil
level sensing system does not check for actual oil level
if the engine has been off for a short period of time, and
the oil level is never sensed while the engine is running.
If the CHECK OIL LEVEL message appears, and your
vehicle has been parked on level ground with the engine
off for at least 30 minutes, the oil level should be
checked by observing the oil dipstick. Prior to checking
the oil level, be sure the engine has been off for five
minutes and your vehicle is on a level surface. Then
check the dipstick and add oil if necessary. See
ªEngine Oilº in the Index.
CHECK WASHER FLUID
- 25: This message will
appear for several seconds indicating that you need
washer solvent.
CRUISE ENGAGED
- 43: This message will appear for
a few seconds when you select a speed at which to cruise.
DOOR AJAR
- 141: A door other than the driver's
door is open or ajar when this message appears. The
vehicle's engine must be running and the transaxle not
in PARK (P) for this message to display. A chime
will also sound when the vehicle's speed is greater than
5 mph (8 km/h).

yellowblue
2-85
DRIVER DOOR AJAR - 140: This message
will display when the vehicle is being shifted out of
PARK (P) with the engine running to signal that the
driver's door is open or ajar. A chime will also sound
when the vehicle's speed is greater than 5 mph (8 km/h).
ENGINE COOLANT HOT, IDLE ENGINE
- 44:
This message will appear when the engine coolant
temperature is over 248
F (126
C). To avoid added
strain on a hot engine, turn off the climate control
system. Stop and allow your vehicle to idle until it cools
down or the message is removed. If it does not cool
down, turn off the engine and have it serviced before
driving it again. Severe engine damage can result from
an overheated engine. See ªEngine Overheatingº in
the Index.
ENGINE HOT
- A/C OFF - 16: This message
displays when the engine coolant becomes hotter than
the normal operating temperature. To avoid added strain
on a hot engine, the air conditioning compressor is
automatically turned off so that air conditioned air is not
delivered. If the coolant temperature returns to normal,
you must select AC to return to a normal A/C
compressor operation. If this message continues to
appear, have the system repaired as soon as possible to
avoid compressor damage.ENGINE MISFIRE, EASE OFF GAS PEDAL
- 114:
An engine misfire has occurred. You'll need to ease off
the gas pedal.
ENGINE OVERHEATED, STOP ENGINE
- 42:
This message will appear when the engine has
overheated. Stop and turn the engine off immediately to
avoid severe engine damage. See ªEngine Overheatingº
in the Index. A multiple chime will also sound when this
message is displayed.
ENGINE POWER REDUCED
- 41: This message
informs the driver that their vehicle is reducing engine
power because the transaxle is being placed in gear
under conditions that may cause damage to the vehicle
powertrain or vehicle acceleration.
FUEL LEVEL LOW
- 11 : This message serves as a
warning that the fuel level in the tank is critically low.
Stop for fuel soon.
HEADLAMPS SUGGESTED
- 23: If it's dark enough
outside and the Twilight Sentinel
control is off, a
HEADLAMPS SUGGESTED message will display on
the DIC. This message informs the driver that turning on
the exterior lamps is recommended even though the
Daytime Running Lamps (DRL) are still illuminated
(it's become dark enough outside to require the
headlamps and/or other exterior lamps).

yellowblue
2-86
ICE POSSIBLE - 13: This message appears when
the outside air temperature is cold enough to create icy
road conditions.
LOW
-REFRIG A/C OFF - 12: This message means
that the air conditioning system detects a refrigerant
level that is low enough to cause damage to the air
conditioning compressor. To avoid damage, the air
conditioning compressor automatically turns off and the
electronic climate control system will automatically
switch from AUTO to ECON and remain there.
Have the air conditioning system serviced if this
message appears.
MONITORED SYSTEMS OK
- 1: This message only
appears in the ªrecallº mode by pressing the RESET NO
(NO INFO RESET) button. It lets you know that no
other messages are stored or currently active.
OIL PRESSURE LOW STOP ENGINE
- 35: If this
message appears while the engine is running, stop the
engine and do not operate it until the cause of low oil
pressure is corrected. Severe damage to the engine can
result. A multiple chime will also sound when this
message is displayed.
OPTIONS NOT SET
- 99: This message will display if
a fault has occurred in your vehicle's memory. See your
dealership for service.PROGRAM PASS KEY
- 31: This warning message
displays when the PASS
-Key
II pellet information has
not been programmed into your vehicle. See your
dealership for service.
PHONE NOT PRESENT
- 126: This message will
appear when the steering wheel controls for the optional
phone system are activated but the phone is not plugged
into the vehicle. Make sure your phone is plugged in. If
your phone appears to be connected, see your dealership
for service.
REMOVE KEY
- 70: This message will appear when
the Personalized Automotive Security System
(PASS
-Key
II) is unable to read the pellet on the
ignition key or an improper key pellet has been inserted.
This message typically appears following the display of
STARTING DISABLED, REMOVE KEY. The
instrument panel cluster will then run a timer and
change the messages to WAIT 3 MINUTES, WAIT 2
MINUTES, WAIT 1 MINUTE and then START CAR.
When the REMOVE KEY message is displayed, remove
the ignition key. Check the ignition key for damage. If it
is damaged, it may need to be replaced. If you see no
damage, clean the pellet contacts with a soft cloth or
napkin before inserting the key back into the ignition.
Have your vehicle serviced if the message still appears.

yellowblue
4-7
Avoid needless heavy braking. Some people drive in
spurts
-- heavy acceleration followed by heavy
braking
-- rather than keeping pace with traffic.
This is a mistake. Your brakes may not have time to
cool between hard stops. Your brakes will wear out
much faster if you do a lot of heavy braking. If you
keep pace with the traffic and allow realistic following
distances, you will eliminate a lot of unnecessary
braking. That means better braking and longer
brake life.
If your engine ever stops while you're driving, brake
normally but don't pump your brakes. If you do, the
pedal may get harder to push down. If your engine
stops, you will still have some power brake assist. But
you will use it when you brake. Once the power assist is
used up, it may take longer to stop and the brake pedal
will be harder to push.
Anti-Lock Brakes (ABS)
Your vehicle has anti-lock brakes (ABS). ABS is an
advanced electronic braking system that will help
prevent a braking skid.
When you start your engine and begin to drive away,
your anti
-lock brake system will check itself. You may
hear a momentary motor or clicking noise while this test
is going on, and you may even notice that your brake
pedal moves a little. This is normal.
If there's a problem with the
anti
-lock brake system, this
warning light will stay on.
See ªAnti
-Lock Brake
System Warning Lightº in
the Index.